SIST EN IEC 61010-2-130:2021
(Main)Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-130: Particular requirements for equipment intended to be used in educational establishments by children (IEC 61010-2-130:2021)
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-130: Particular requirements for equipment intended to be used in educational establishments by children (IEC 61010-2-130:2021)
EN-IEC 61010-2-130 specifies particular safety requirements for the following types of equipment a), b) or c) and their accessories intended to be used in educational establishments by children under the supervision of the RESPONSIBLE BODY. It specifies general safety requirements for equipment intended to be used in educational establishments by persons between the age of 3 years and the age of 16 years under the supervision of a RESPONSIBLE BODY.Children are considered as persons between the age of 3 years and 16 years.It is recognized that pupils with additional educational or physical support needs may have needs beyond the level addressed in this document (see Clause 17 risk assessment).It is possible that all or part of the equipment falls within the scope of one or more IEC 61010 Part 2 standards as well as within the scope of this document. In that case the requirements of those other Part 2 standards apply.
Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2-130: Besondere Anforderungen an Geräte, die für den Gebrauch in Bildungseinrichtungen durch Kinder vorgesehen sind (IEC 61010-2-130:2021)
Exigences de sécurité pour appareils électriques de mesurage, de régulation et de laboratoire - Partie 2-130: Exigences particulières pour appareils destinés à une utilisation dans les établissements scolaires par des enfants (IEC 61010-2-130:2021)
L'IEC 61010-2-130:2021 spécifie les exigences spécifiques de sécurité pour les types suivants d'appareils a), b) ou c) et leurs accessoires, destinés à être utilisés dans les établissements scolaires par des enfants sous la supervision de l'autorité responsable. Elle spécifie les exigences générales de sécurité pour les appareils destinés à être utilisés dans les établissements scolaires par des personnes âgées entre 3 et 16 ans sous la supervision de l’autorité responsable.
Cette première édition annule et remplace l’IEC TS 62850 parue en 2013.
Cette édition inclut les modifications techniques majeures suivantes par rapport à l’IEC TS 62850:
a) exigences de marquage et de documentation;
b) exigences de stabilité et de manipulation.
Varnostne zahteve za električno opremo za meritve, nadzor in laboratorijsko uporabo - 2-130. del: Posebne zahteve za opremo, ki jo uporabljajo otroci v izobraževalnih ustanovah (IEC 61010-2-130:2021)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 61010-2-130:2021
01-september-2021
Varnostne zahteve za električno opremo za meritve, nadzor in laboratorijsko
uporabo - 2-130. del: Posebne zahteve za opremo, ki jo uporabljajo otroci v
izobraževalnih ustanovah (IEC 61010-2-130:2021)
Safety requirements for electrical equipment for measurement, control, and laboratory
use - Part 2-130: Particular requirements for equipment intended to be used in
educational establishments by children (IEC 61010-2-130:2021)
Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2
-130: Besondere Anforderungen an Geräte, die für den Gebrauch in
Bildungseinrichtungen durch Kinder vorgesehen sind (IEC 61010-2-130:2021)
Exigences de sécurité pour appareils électriques de mesurage, de régulation et de
laboratoire - Partie 2-130: Exigences particulières pour appareils destinés à une
utilisation dans les établissements scolaires par des enfants (IEC 61010-2-130:2021)
Ta slovenski standard je istoveten z: EN IEC 61010-2-130:2021
ICS:
19.080 Električno in elektronsko Electrical and electronic
preskušanje testing
71.040.10 Kemijski laboratoriji. Chemical laboratories.
Laboratorijska oprema Laboratory equipment
SIST EN IEC 61010-2-130:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 61010-2-130:2021
---------------------- Page: 2 ----------------------
SIST EN IEC 61010-2-130:2021
EUROPEAN STANDARD EN IEC 61010-2-130
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2021
ICS 19.080
English Version
Safety requirements for electrical equipment for measurement,
control, and laboratory use - Particular requirements for
equipment intended to be used in educational establishments by
children
(IEC 61010-2-130:2021)
Exigences de sécurité pour appareils électriques de Sicherheitsbestimmungen für elektrische Mess-, Steuer-,
mesurage, de régulation et de laboratoire - Partie 2-130: Regel- und Laborgeräte - Teil 2-130: Besondere
Exigences particulières pour appareils destinés à une Anforderungen an Geräte, die für den Gebrauch in
utilisation dans les établissements scolaires par des enfants Bildungseinrichtungen durch Kinder vorgesehen sind
(IEC 61010-2-130:2021) (IEC 61010-2-130:2021)
This European Standard was approved by CENELEC on 2021-04-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61010-2-130:2021 E
---------------------- Page: 3 ----------------------
SIST EN IEC 61010-2-130:2021
EN IEC 61010-2-130:2021 (E)
European foreword
The text of document 66/724/FDIS, future edition 1 of IEC 61010-2-130, prepared by IEC/TC 66
"Safety of measuring, control and laboratory equipment" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN IEC 61010-2-130:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-01-27
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-04-27
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 61010-2-130:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60086-1 NOTE Harmonized as EN 60086-1
IEC 61010-031 NOTE Harmonized as EN 61010-031
IEC 61439-1 NOTE Harmonized as EN 61439-1
IEC 62368-1 NOTE Harmonized as EN IEC 62368-1
ISO 13857:2019 NOTE Harmonized as EN ISO 13857:2019 (not modified)
2
---------------------- Page: 4 ----------------------
SIST EN IEC 61010-2-130:2021
EN IEC 61010-2-130:2021 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Annex ZA of EN 61010-1:2010/A1:2019 is applicable with the following changes:
Delete the following:
Publication Year Title EN/HD Year
IEC 61010-031 2002 Safety requirements for electrical EN 61010-031 2002
equipment for measurement, control and
+ A1 2008 + A1 2008
laboratory use – Part 031: Safety
requirements for hand-held probe
assemblies for electrical measurement
and test
3
---------------------- Page: 5 ----------------------
SIST EN IEC 61010-2-130:2021
EN IEC 61010-2-130:2021 (E)
Annex ZZ
(informative)
Relationship between this European standard and the safety
objectives of Directive 2014/35/EU [2014 OJ L96] aimed to be
covered
This European standard has been prepared under a Commission’s standardization request relating to
harmonized standards in the field of the Low Voltage Directive, M/511, to provide one voluntary means
of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of the
Council of 26 February 2014 on the harmonization of the laws of the Member States relating to the
making available on the market of electrical equipment designed for use within certain voltage limits
[2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding safety objectives of
that Directive, and associated EFTA regulations.
Table ZZ.1 — Correspondence between this European standard and Annex I of Directive
2014/35/EU [2014 OJ L96]
Clause(s) / sub-
Safety objectives of Directive
clause(s)
Remarks / Notes
2014/35/EU (Annex I)
of this EN
1. General conditions
1 (a) the essential characteristics, the 5.1
recognition and observance of which will
5.2
ensure that electrical equipment will be
5.3
used safely and in applications for which it
5.4
was made, shall be marked on the
electrical equipment, or, if this is not
possible, on an accompanying document
1 (b) the electrical equipment, together 5.4
with its component parts, shall be made in
6.6
such a way as to ensure that it can be
6.10
safely and properly assembled and
6.11
connected
Annex F
1 (c) the electrical equipment shall be so 5.4
designed and manufactured as to ensure
Annex F
that protection against the hazards set out
17 (for hazards
in points 2 and 3 is assured, providing that
not covered by
the equipment is used in applications for
clauses 6-16)
which it was made and is adequately
See also the
maintained
details in points 2
and 3
2. Protection against hazards arising from the electrical equipment
Measures of a technical nature shall be laid down in accordance with point 1, in order to ensure that:
4
---------------------- Page: 6 ----------------------
SIST EN IEC 61010-2-130:2021
EN IEC 61010-2-130:2021 (E)
Clause(s) / sub-
Safety objectives of Directive
clause(s)
Remarks / Notes
2014/35/EU (Annex I)
of this EN
2 (a) persons and domestic animals are 4, 6.1 – 6.11, 9.6,
adequately protected against the danger 11.6, 14.4
of physical injury or other harm which
Annex D
might be caused by direct or indirect
Annex F, Annex
contact
K
2 (b) temperatures, arcs or radiation which 4, 4.4.4.2,
would cause a danger, are not produced 6.3.1.b) 2),
6.3.2 b) 2),
9.5, 9.6, 10.1 -
10.5, 12
2 (c) persons, domestic animals and 4, 4.4, 7.2- 7.7, 9,
property are adequately protected against 12.3, 12.5, 12.6,
non-electrical dangers caused by the 13.1, 13.2, 16.2
electrical equipment which are revealed
by experience
2 (d) the insulation is suitable for 4, 6.7,
foreseeable conditions
Annex K
3. Protection against hazards which may be caused by external influences on the electrical
equipment
Technical measures shall be laid down in accordance with point 1, in order to ensure that the electrical
equipment:
3 (a) meets the expected mechanical 4, 7, 8
requirements in such a way that persons,
domestic animals and property are not
endangered
3 (b) is resistant to non-mechanical 1.4, 4, 6.7.2.2.1,
influences in expected environmental 10.5, 11.6,
conditions, in such a way that persons,
14.3, 14.8,
domestic animals and property are not
14.101, 15
endangered
3 (c) does not endanger persons, 4, 9, 14, 16.1
domestic animals and property in
foreseeable conditions of overload
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
5
---------------------- Page: 7 ----------------------
SIST EN IEC 61010-2-130:2021
---------------------- Page: 8 ----------------------
SIST EN IEC 61010-2-130:2021
IEC 61010-2-130
®
Edition 1.0 2021-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Safety requirements for electrical equipment for measurement, control, and
laboratory use –
Part 2-130: Particular requirements for equipment intended to be used in
educational establishments by children
Exigences de sécurité pour appareils électriques de mesurage, de régulation et
de laboratoire –
Partie 2-130: Exigences particulières pour appareils destinés à une utilisation
dans les établissements scolaires par des enfants:
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 19.080 ISBN 978-2-8322-9492-5
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 9 ----------------------
SIST EN IEC 61010-2-130:2021
– 2 – IEC 61010-2-130:2021 © IEC 2021
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope and object . 6
2 Normative references . 7
3 Terms and definitions . 7
4 Tests . 7
5 Marking and documentation . 8
6 Protection against electric shock . 11
7 Protection against mechanical HAZARDS . 12
8 Resistance to mechanical stresses . 17
9 Protection against the spread of fire . 17
10 Equipment temperature limits and resistance to heat . 17
11 Protection against HAZARDS from fluids and solid foreign objects . 18
12 Protection against radiation, including laser sources, and against sonic and
ultrasonic pressure . 18
13 Protection against liberated gases and substances, explosion and implosion . 19
14 Components and subassemblies . 19
15 Protection by interlocks . 20
16 HAZARDS resulting from application . 21
17 RISK assessment . 21
Annexes . 22
Annex B (normative) Standard test probes . 23
Annex L (informative) Index of defined terms . 24
Bibliography . 25
Figure 101 – Irregular openings . 16
Figure 102 – Cylinder for checking the size of small components . 20
Figure B.101 – Jointed test probe for equipment intended to be used by children . 23
Table 1 – Symbols . 9
Table 13 – Minimum maintained gaps to prevent crushing for different body parts for
adults and PUPIL OPERATORS aged 3 years and above . 13
Table 14 – Maximum gaps to prevent access for different body parts for adults and
PUPIL OPERATORS aged 14 years and above . 14
Table 101 – Minimum safety distances to limit access for different body parts for PUPIL
OPERATORS aged 3 years to 13 years . 15
Table 19 – Surface temperature limits in NORMAL CONDITION . 18
---------------------- Page: 10 ----------------------
SIST EN IEC 61010-2-130:2021
IEC 61010-2-130:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT
FOR MEASUREMENT, CONTROL, AND LABORATORY USE –
Part 2-130: Particular requirements for equipment intended
to be used in educational establishments by children
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61010-2-130 has been prepared by IEC Technical Committee 66:
Safety of measuring, control and laboratory equipment.
This first edition cancels and replaces IEC TS 62850, published in 2013.
This edition includes the following significant technical changes with respect to IEC TS 62850:
a) marking and documentation requirements;
b) stability and handling requirements.
---------------------- Page: 11 ----------------------
SIST EN IEC 61010-2-130:2021
– 4 – IEC 61010-2-130:2021 © IEC 2021
The text of this International Standard is based on the following documents:
FDIS Report on voting
66/724/FDIS 66/726/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2 and taking
into account ISO/IEC Guide 50:2014.
A list of all parts in the IEC 61010 series, published under the general title Safety
requirements for electrical equipment for measurement, control, and laboratory use, can be
found on the IEC website.
This document is to be used in conjunction with IEC 61010-1. It was established based on the
third edition (2010) of IEC 61010-1, including its Amendment 1 (2016) hereinafter referred to
as Part 1.
This document supplements or modifies the corresponding clauses in IEC 61010-1 to convert
that publication into the IEC standard: Particular requirements for equipment intended to be
used in educational establishments by children.
Where a particular subclause of Part 1 is not mentioned in this document, that subclause
applies as far as is reasonable. Where this document states "addition", "modification",
"replacement", or "deletion", the relevant requirement, test specification or note in Part 1
should be adapted accordingly.
In this standard, the following print types are used:
• requirements: in roman type;
• NOTES: in smaller roman type;
• conformity assessment and test: in italic type;
• terms defined used throughout this standard which have been defined in Clause 3: SMALL
ROMAN CAPITALS.
Subclauses, figures, tables and notes which are additional to those in Part 1 are numbered
starting from 101. Additional annexes are lettered starting from AA and additional list items
are lettered from aa).
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 12 ----------------------
SIST EN IEC 61010-2-130:2021
IEC 61010-2-130:2021 © IEC 2021 – 5 –
INTRODUCTION
This document specifies particular safety requirements for equipment and accessories
intended to be used in educational establishment by PUPIL OPERATORS. PUPIL OPERATORS are
for the sake of this document, children between the ages of 3 years and 16 years operating
electrical equipment under supervision of a RESPONSIBLE BODY.
Equipment and accessories are considered intended for use in educational establishments,
when it is either explicitly stated in accompanying documentation, or where sales and
marketing materials indicate such intended use. This does not limit the use of other
equipment for use in educational establishments, however equipment and accessories not
evaluated to the requirements of this document may need additional precautions and
attestation when used by PUPIL OPERATORS.
Readily predictable behaviour of PUPIL OPERATORS can include poking objects and materials
associated with equipment and accessories, which poses additional challenges for
determination of reasonably foreseeable misuse. Consequently, more stringent criteria for
access to potentially hazardous parts are required for educational establishment equipment
than for general laboratory use.
Moreover, the maximum temperatures of parts that may be touched by children should be
lower than for equipment handled only by adults. Ergonomic considerations and mechanical
risks need to be addressed with regard to the anthropomorphic dimensions of children instead
of adults.
This document includes the following significant changes with respect to Part 1, as well as
other changes:
a) a marking is added to indicate to the RESPONSIBLE BODY that the equipment is intended to
be used by PUPIL OPERATORS under supervision;
b) accessibility requirements are enhanced to take into account the propensity of children to
insert foreign objects wherever they can;
c) temperature limits have been decreased to take into account the greater sensitivity of a
child's skin;
d) mechanical access dimensions have been reduced to take into account the smaller
dimensions of a child's body;
e) limits for non-collimated optical radiation have been introduced;
f) limits for ionizing radiation have been reduced;
g) small detachable parts below certain dimensions have been prohibited;
h) manufacturers are required to consider the general unpredictability of the behaviour of
PUPIL OPERATORS.
---------------------- Page: 13 ----------------------
SIST EN IEC 61010-2-130:2021
– 6 – IEC 61010-2-130:2021 © IEC 2021
SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT
FOR MEASUREMENT, CONTROL, AND LABORATORY USE –
Part 2-130: Particular requirements for equipment intended
to be used in educational establishments by children
1 Scope and object
This clause of Part 1 is applicable except as follows:
1.1.1 Equipment included in scope
Deletion: Delete paragraph 1.
Replacement:
Replace the second paragraph immediately before the lettered list, with the following:
This part of IEC 61010 specifies particular safety requirements for the following types of
equipment a), b) or c) and their accessories intended to be used in educational
establishments by children under the supervision of the RESPONSIBLE BODY. It specifies
general safety requirements for equipment intended to be used in educational establishments
by persons between the age of 3 years and the age of 16 years under the supervision of a
RESPONSIBLE BODY.
Children are considered as persons between the age of 3 years and 16 years.
It is recognized that pupils with additional educational or physical support needs may have
needs beyond the level addressed in this document (see Clause 17 risk assessment).
NOTE 1 The term "children" used in this document does not match the definitions found in ISO/IEC Guide 50 and
other documents.
It is possible that all or part of the equipment falls within the scope of one or more IEC 61010
Part 2 standards as well as within the scope of this document. In that case the requirements
of those other Part 2 standards apply.
NOTE 2 In some countries, age limits can be different from those used in this document or can be replaced by
capability requirements.
Renumber the existing NOTE 1 and NOTE 2 as NOTE 3 and NOTE 4.
1.1.3 Computing equipment
Renumber NOTE as NOTE 1.
Addition:
Add the following note after the existing note.
NOTE 2 General information technology equipment such as projector, tablet PC, monitor, electronic whiteboard,
power supplies, etc. used by children in an educational establishment are excluded from the scope unless those
are specifically designed for the type of equipment covered under the scope of IEC 61010-1 or any of its Part 2
standards.
---------------------- Page: 14 ----------------------
SIST EN IEC 61010-2-130:2021
IEC 61010-2-130:2021 © IEC 2021 – 7 –
1.2.1 Aspects included in scope
Replace the existing note by the following notes:
NOTE 1 Attention is drawn to the additional requirements that can be specified by national authorities responsible
for health and safety in education. In particular, there can be limitations on the use of radioactive materials, X-ray
and laser equipment and hazardous substances.
NOTE 2 Attention is also drawn to the existence of additional requirements that can be specified by national
authorities responsible for the health and safety of children in education with special needs.
2 Normative references
This clause of Part 1 is applicable except as follows:
Delete:
IEC 61010-031, Safety requirements for electrical equipment for measurement, control and
laboratory use – Part 031: Safety requirements for hand-held probe assemblies for electrical
measurement and test
3 Terms and definitions
This clause of Part 1 is applicable except as follows:
3.5.11
OPERATOR
After the definition, add the note:
Note 1 to entry: Within this document, the term "OPERATOR" indicates either an adult OPERATOR or a PUPIL
OPERATOR, unless otherwise specified.
3.5.14
REASONABLY FORESEEABLE MISUSE
Add the note:
Note 1 to entry: The age of the child will affect the predictability of the behaviour.
Add the following new term entry:
3.5.101
PUPIL OPERATOR
child receiving education in an educational establishment under the supervision of the
RESPONSIBLE BODY
4 Tests
This clause of Part 1 is applicable except as follows:
4.3.2 State of equipment
This subclause of Part 1 is applicable except as follows:
---------------------- Page: 15 ----------------------
SIST EN IEC 61010-2-130:202
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.