SIST EN 10058:2019
(Main)Hot rolled flat steel bars and steel wide flats for general purposes - Dimensions and tolerances on shape and dimensions
Hot rolled flat steel bars and steel wide flats for general purposes - Dimensions and tolerances on shape and dimensions
This European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled steel flat bars and steel wide flats for general purposes.
This standard is not applicable to spring leaves, see EN 10092-1.
Warmgewalzte Flachstäbe aus Stahl und Breitflachstahl für allgemeine Verwendung - Maße, Formtoleranzen und Grenzabmaße
Diese Europäische Norm legt die Nennmaße, Grenzabmaße und Formtoleranzen für warmgewalzte Flachstäbe aus Stahl und Breitflachstahl für allgemeine Verwendung fest.
Diese Norm gilt nicht für Flachstäbe für Federn, siehe EN 10092-1.
Plats et larges plats en acier laminés à chaud pour usages généraux - Dimensions et tolérances sur la forme et les dimensions
La présente Norme européenne spécifie les dimensions nominales et les tolérances sur les dimensions et la forme des plats et larges plats en acier laminés à chaud pour usages généraux.
La présente norme ne s’applique pas aux lames de ressorts, voir l’EN 10092-1.
Vroče valjane ploske jeklene palice in jeklene široke plošče za splošne namene - Mejni odstopki mer in tolerance oblik
Ta evropski standard določa nazivne mejne odstopke mer in tolerance oblik vroče valjanih ploskih jeklenih palic in jeklenih širokih plošč za splošne namene.
Ta standard se ne uporablja za listnate vzmeti, glej standard EN 10092-1.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgewalzte Flachstäbe aus Stahl und Breitflachstahl für allgemeine Verwendung - Maße, Formtoleranzen und GrenzabmaßePlats et larges plats en acier laminés à chaud pour usages généraux - Dimensions et tolérances sur la forme et les dimensionsHot rolled flat steel bars and steel wide flats for general purposes - Dimensions and tolerances on shape and dimensions77.140.60Jeklene palice in drogoviSteel bars and rodsICS:Ta slovenski standard je istoveten z:EN 10058:2018SIST EN 10058:2019en,fr,de01-februar-2019SIST EN 10058:2019SLOVENSKI
STANDARDSIST EN 10058:20041DGRPHãþD
SIST EN 10058:2019
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10058
November
t r s z ICS
y yä s v rä x r Supersedes EN
s r r w zã t r r uEnglish Version
Hot rolled flat steel bars and steel wide flats for general purposes æ Dimensions and tolerances on shape and dimensions Plats et larges plats en acier laminßs à chaud pour usages gßnßraux æ Dimensions et tolßrances sur la forme et les dimensions
Warmgewalzte Flachstäbe aus Stahl und Breitflachstahl für allgemeine Verwendung æ Maßeá Formtoleranzen und Grenzabmaße This European Standard was approved by CEN on
w October
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r r w zã t r s z ESIST EN 10058:2019
EN 10058:2018 (E) 2 Contents Page
European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Designation. 4 5 Dimensions . 4 6 Tolerances on dimensions and shape . 6 6.1 Thickness (t) . 6 6.2 Width (b) . 6 6.3 Length (L) . 6 6.4 Straightness (q) . 6 6.5 Out-of-squareness (u) . 6 6.6 Maximum permissible variation in thickness across the width for wide flats . 6 7 Measurement . 8 7.1 Thickness and width . 8 7.2 Length . 8 7.3 Straightness . 8 7.4 Out-of-squareness . 8 7.5 Maximum permissible variation in thickness across the width for wide flats . 8 Bibliography . 9
SIST EN 10058:2019
EN 10058:2018 (E) 3 European foreword This document (EN 10058:2018) has been prepared by Technical Committee ECISS/TC 103 “Structural steels other than reinforcement”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2019, and conflicting national standards shall be withdrawn at the latest by May 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10058:2003. In comparison to the previous edition following technical changes were made: — width of 130 and 140 mm were added for the flat bars; — wide flats were introduced in this standard with widths of 160, 170, 180 and 200 mm; — for wide flats maximum permissible thickness variation was introduced; — standard was editorially revised. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, I
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.