Railway applications - Wheel/Rail friction management - Part 2-1: Properties and Characteristics - Flange lubricants

This European Standard specifies the requirements of lubricants intended for lubrication of the active interface (wheel flange and the gauge face of the rail/ back of wheel and check rail).
It outlines the information required for most approval procedures, the method of testing and routine control/monitoring of the lubricant.

Bahnanwendungen - Reibungsmanagement zwischen Rad und Schiene - Teil 2-1 : Eigenschaften und Merkmale - Spurkranzschmierstoffe

Applications ferroviaires - Gestion des frottements roue/rail - Partie 2-1: Propriétés et caractéristiques - Lubrification des boudins de roues

Železniške naprave - Trenje na stiku kolo-tirnica - 2-1. del: Lastnosti in značilnosti - Maziva za prirobnice

General Information

Status
Not Published
Public Enquiry End Date
23-Dec-2020
Technical Committee
Current Stage
5020 - Formal vote (FV) (Adopted Project)
Start Date
28-Oct-2021
Due Date
16-Dec-2021

RELATIONS

Buy Standard

Draft
oSIST prEN 15427-2-1:2020 - BARVE na PDF-str 41,42,44,45,48,50,52,53,54,55,56
English language
57 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN 15427-2-1:2020
01-december-2020

Železniške naprave - Trenje na stiku kolo-tirnica - 2-1. del: Lastnosti in značilnosti

- Maziva za prirobnice
Railway applications - Wheel/Rail friction management - Part 2-1: Properties and
Characteristics - Flange lubricants
Bahnanwendungen - Reibungsmanagement zwischen Rad und Schiene - Teil 2-1 :
Eigenschaften und Merkmale - Spurkranzschmierstoffe

Applications ferroviaires - Gestion des frottements roue/rail - Partie 2-1: Propriétés et

caractéristiques - Lubrification des boudins de roues
Ta slovenski standard je istoveten z: prEN 15427-2-1
ICS:
21.260 Mazalni sistemi Lubrication systems
45.040 Materiali in deli za železniško Materials and components
tehniko for railway engineering
oSIST prEN 15427-2-1:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15427-2-1:2020
---------------------- Page: 2 ----------------------
oSIST prEN 15427-2-1:2020
DRAFT
EUROPEAN STANDARD
prEN 15427-2-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2020
ICS 45.040; 75.100 Will supersede EN 16028:2012
English Version
Railway applications - Wheel/Rail friction management -
Part 2-1: Properties and Characteristics - Flange lubricants

Applications ferroviaires - Gestion des frottements Bahnanwendungen - Reibungsmanagement zwischen

roue/rail - Partie 2-1: Propriétés et caractéristiques - Rad und Schiene - Teil 2-1 : Eigenschaften und

Lubrification des boudins de roues Merkmale - Spurkranzschmierstoffe

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee

CEN/TC 256.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15427-2-1:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
Contents Page

European foreword ............................................................................................................................... 4

Introduction ............................................................................................................................................ 5

1 Scope ............................................................................................................................................ 6

2 Normative references ............................................................................................................ 6

3 Terms and definitions ........................................................................................................... 7

4 Lubricant requirements ....................................................................................................... 8

5 General requirements ........................................................................................................... 9

5.1 Introduction .............................................................................................................................. 9

5.2 Product specification ............................................................................................................. 9

5.3 Technical file ............................................................................................................................. 9

6 Control and monitoring of product ................................................................................ 10

6.1 Manufacturing process ....................................................................................................... 10

6.2 Composition of lubricant ................................................................................................... 10

6.3 Routine tests .......................................................................................................................... 10

6.4 Additional measures ........................................................................................................... 10

7 Technical datasheet............................................................................................................. 10

7.1 General ..................................................................................................................................... 10

7.2 Grease type lubricant characteristics ........................................................................... 10

7.3 Oil type lubricant characteristics ................................................................................... 10

7.4 Solid type lubricant characteristics ............................................................................... 11

8 Packaging, labelling and storage .................................................................................... 11

Annex A (normative) Requirements for lubricants and testing ....................................... 12

A.1 Explanation of Annex A: Tables A.1 to A.4 ................................................................... 12

A.2 Key to Annex A table columns ‘Type’, ‘Routine’ and ‘Datasheet’ ......................... 12

A.3 Key to Annex A table column ‘Use’ ................................................................................. 12

Annex B (informative) Water wash-off test ............................................................................. 24

B.1 Purpose .................................................................................................................................... 24

B.2 Short description .................................................................................................................. 24

B.3 Conditions for testing ......................................................................................................... 24

B.4 Test process............................................................................................................................ 24

Annex C (informative) Corrosion test on steel ....................................................................... 26

C.1 General ..................................................................................................................................... 26

C.2 Short description .................................................................................................................. 26

C.3 Conditions for testing ......................................................................................................... 26

C.4 Test process............................................................................................................................ 27

---------------------- Page: 4 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
Annex D (informative) Behaviour at an elevated temperature – Adhesion on steel

sheet .......................................................................................................................................... 28

D.1 Purpose .................................................................................................................................... 28

D.2 Short description .................................................................................................................. 28

D.3 Conditions for test ................................................................................................................ 28

D.4 Test process............................................................................................................................ 28

Annex E (informative) Determination of the volatile constituents in greases ........... 30

E.1 Purpose .................................................................................................................................... 30

E.2 Short description .................................................................................................................. 30

E.3 Conditions for testing ......................................................................................................... 30

E.4 Test process............................................................................................................................ 30

E.5 Recording of test results .................................................................................................... 31

Annex F (informative) Peak forming and droop .................................................................... 32

F.1 Purpose .................................................................................................................................... 32

F.2 Short description .................................................................................................................. 32

F.3 Conditions for testing ......................................................................................................... 32

F.4 Test process............................................................................................................................ 32

Annex G (informative) Functional test on specific equipment ......................................... 35

G.1 General ..................................................................................................................................... 35

G.2 Flowing behaviour of wheel-flange greases ............................................................... 35

G.3 Test of spraying of lubricants at various temperatures ......................................... 37

Annex H (informative) Solid flange lubricant stick testing and starvation test on

twin-disc machine ................................................................................................................ 41

H.1 Purpose .................................................................................................................................... 41

H.2 Short description .................................................................................................................. 41

H.3 Conditions for test ................................................................................................................ 41

H.4 Required testing and measuring equipment ............................................................. 42

H.5 Test process............................................................................................................................ 43

H.6 Test settings ........................................................................................................................... 44

H.7 Test results ............................................................................................................................. 44

Annex I (informative) MTM machine creep curve test ........................................................ 46

I.1 General ..................................................................................................................................... 46

I.2 Test equipment ..................................................................................................................... 46

I.3 Application of Flange lubricant to metal disk ............................................................ 47

I.4 Performance of the Test .................................................................................................... 48

I.5 Evaluation of the Test ......................................................................................................... 51

Bibliography ......................................................................................................................................... 55

---------------------- Page: 5 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
European foreword

This document (prEN 15427-2-1:2020) has been prepared by Technical Committee CEN/TC 256

“Railway Applciations”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 16028:2012.
---------------------- Page: 6 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
Introduction

Friction management using solid or fluid (oil, grease, etc.) substances at the wheel-rail interface

is a complex subject and includes the following aspects:

— lubrication of the wheel flange / rail gauge corner interface, commonly referred to as “flange

or rail lubrication”;

— lubrication of the back of flange/ check rail interface; commonly referred to as “check rail

lubrication”

— altering the level of friction at the interface between the top of rail and the wheel tread,

commonly referred to as “top of rail friction management”.

— altering the level of adhesion at the interface between the top of rail and the wheel tread.

This document sets out requirements for the lubricant for flange or rail lubrication. It specifies

requirements for the lubricant, how to test it and how to approve it.
Lubricants should be tested to confirm there is:
— compatibility with lubricating systems;
— no intolerable increased risk of fire;
— meets relevant environmental requirements;

— no incompatibility between the different lubricants in use, particularly between solid and

fluid systems;
— satisfactory and consistent product quality and performance.
— no degradation to the safety of the railway (braking, signalling).

The main purpose of the lubricant is to reduce friction and wear and reduce the risk of flange

climb derailment.
---------------------- Page: 7 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
1 Scope

This document specifies the requirements of lubricants intended for lubrication of the wheel-rail

interface between the wheel and the rail (active interface) applied either directly or indirectly to

the wheel or to the rail.

It outlines the information required for most approval procedures, the method of testing and

routine control/monitoring of the lubricant.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies.

For undated references, the latest edition of the referenced document (including any

amendments) applies.

EN 10130, Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions

EN ISO 868, Plastics and ebonite - Determination of indentation hardness by means of a durometer

(Shore hardness) (ISO 868)

EN ISO 1183-1, Plastics - Methods for determining the density of non-cellular plastics - Part 1:

Immersion method, liquid pycnometer method and titration method (ISO 1183-1)

EN ISO 2592, Petroleum and related products - Determination of flash and fire points - Cleveland

open cup method (ISO 2592)

EN ISO 3146, Plastics - Determination of melting behaviour (melting temperature or melting range)

of semi-crystalline polymers by capillary tube and polarizing-microscope methods (ISO 3146)

EN ISO 3675, Crude petroleum and liquid petroleum products - Laboratory determination of density

- Hydrometer method (ISO 3675)

EN ISO 12185, Crude petroleum and petroleum products - Determination of density - Oscillating U-

tube method (ISO 12185)

EN ISO 20623, Petroleum and related products - Determination of the extreme-pressure and anti-

wear properties of lubricants - Four-ball method (European conditions) (ISO 20623)

ISO 760, Determination of water — Karl Fischer method (General method)
ISO 2049, Petroleum products — Determination of colour (ASTM scale)

ISO 2137, Petroleum products and lubricants — Determination of cone penetration of lubricating

greases and petrolatum

ISO 2176, Petroleum products — Lubricating grease — Determination of dropping point

ISO 3733, Petroleum products and bituminous materials — Determination of water — Distillation

method

ISO 6072, Rubber — Compatibility between hydraulic fluids and standard elastomeric materials

---------------------- Page: 8 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020

ISO 6743-99, Lubricants, industrial oils and related products (class L) — Classification — Part 99:

General

ISO 13737, Petroleum products and lubricants — Determination of low-temperature cone

penetration of lubricating greases

DIN 51777-2, Testing of mineral oil-hydrocarbons and solvents — Determination of the water

content according to Karl Fischer (indirect method)

DIN 51350-4, Testing of lubricants — Testing by the Shell four-ball tester — Determination of

welding load of consistent lubricants

DIN 51350-5, Testing of lubricants — Testing by the Shell four-ball tester — Determination of wear

data for consistent lubricants
DIN 51631, Mineral spirits — Special boiling point spirits — Requirements

DIN 51807-1, Testing of lubricants — Test of the behaviour of lubricating greases in the presence

of water — Static test

DIN 51817, Testing of lubricants — Determination of oil separation from greases under static

conditions
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following

addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
3.1
lubricant
substance that is designed to lower friction and wear
3.2
oil
liquid lubricant

Note 1 to entry: Oil can be mineral, natural or synthetic in origin and can have additives included.

3.3
grease
semi-solid lubricant

Note 1 to entry: Grease consists of a thickener and additives integrated in a lubricating oil.

3.4
stick
encapsulated solid lubricant

Note 1 to entry: Typically, the stick comprises a solid lubricant which is encapsulated in a polymeric

binder/carrier. The product is designed for direct contact with a rotating wheel flange; the polymeric

binder has a sufficiently high melting point such that it does not melt but rather wears when in contact with

the wheel flange to ensure dimensional stability.
---------------------- Page: 9 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
3.5
batch

entire content of a single identified production of lubricant from the same manufacturing process

3.6
active interface
contact area between the wheel flange root and the rail gauge corner
Note 1 to entry: For more information on this definition, see EN 15427.
3.7
flange lubrication
lubrication of the active interface by applying a lubricant to the wheel flange
3.8
rail lubrication

lubrication of the active interface by applying a lubricant to the rail gauge side face

3.9
Lubricant Application Unit (LAU)

component of the lubrication system (trainborne or trackside) that delivers lubricant to the active

interface

Note 1 to entry: This includes spray nozzles, trackside grease distribution units/blades, stick applicators,

etc.
3.10
lubrication system
components required to apply lubricant to the active interface

Note 1 to entry: A lubrication system can include one or more Lubricant Application Units, a reservoir unit,

pump and/or a control device.
3.11
trainborne equipment

system carried on the train that consists of one or more applicators, a storage unit and a means

of control
3.12
trackside equipment

system installed on or adjacent to the track that consists of one or more applicators, storage

containers and a means of control
3.13
operating temperature
temperature range in which the lubricant can be applied effectively
4 Lubricant requirements

The lubricant, when applied within the specified limits, shall not compromise the safety of the

railway (i.e braking distances, signalling systems, etc.)

NOTE Specified limits are normally understood and agreed between relevant parties before use of

lubricant.
---------------------- Page: 10 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
5 General requirements
5.1 Introduction

This clause outlines the information required to gain approval on most railway networks. It does

not cover its performance on the railway.
5.2 Product specification

The product specification shall be fully documented and shall include the following information:

a) purpose of lubricant;
b) conformity to the applicable type tests as set out in Tables A.1 to A.3;

c) conformance with other relevant local requirements (such as environmental, fire, toxicity,

etc…);
d) application data:
1) including equipment, it can be used with (see Annex G - K);
2) operating temperatures;

NOTE 1 The typical operating temperature range to take into account is from −25 °C to +80 °C.

e) additional validation tests (see Table A.4);
f) any previous relevant experience (i.e. use in other countries);
g) conditions for packaging and labelling (see Clause 8);
h) environmental tests are defined in Tables A.1 to A.3.

NOTE 2 Where legislation and regulations (European, national or local) concerning ecological and

environmental compatibility of lubricants (biodegrability, toxicity, etc.) are applicable, consideration will

need to be given to the relevant requirements.
5.3 Technical file

A file of technical data showing compliance with the requirements in the product specification

and the results of type tests and trials shall be provided. A technical datasheet shall also be

provided (see Clause 7).

A material safety data sheet (MSDS) for the product in the language of the interested customer or

country shall be included.
---------------------- Page: 11 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
6 Control and monitoring of product
6.1 Manufacturing process

If the manufacturing process is changed in a way that can affect the chemical composition, the

new process shall be documented and the customer shall be notified.
NOTE In some cases, this leads to a new approval being required.
6.2 Composition of lubricant

If the composition of the lubricant is changed in any way, it shall be documented and the customer

shall be notified.
NOTE In some cases, this leads to a new approval being required.
6.3 Routine tests
Routine tests ensure product consistency from batch to batch.

The routine tests are listed in Tables A1 to A3. If additional tests are required (such as those not

included in the tables or a type test) this and the frequency can be agreed between the client and

supplier.

The sample of lubricant assessed for quality testing shall have been manufactured in a regular

production batch. The entire sample of material used for the approval tests shall be taken from

the same production batch and delivered in a single consignment.
The results of the routine tests shall be recorded.
6.4 Additional measures

Retention of test records and samples, witnessing of tests, calibration of test equipment shall be

considered.
7 Technical datasheet
7.1 General

The technical datasheet shall include the individual identifying code or name of the lubricant, a

description of the product’s field of use and typical means of application. For each lubricant type,

the information in the following subclauses shall also be included.
7.2 Grease type lubricant characteristics

The product shall be described by its consistency, its temperature range, the type of thickener

and type of base oil used. Where solid particulates are used, the type and content shall be

reported. Further technical data shall be provided as listed under the ‘datasheet’ column in

Table A.1.
7.3 Oil type lubricant characteristics

The product shall be described by its viscosity, its temperature range and by the type of oil used.

Where solid particulates are used the type and content shall be reported. Further technical data

shall be provided as listed under the ‘datasheet’ column in Table A.2.
---------------------- Page: 12 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
7.4 Solid type lubricant characteristics

The product shall be described by its melting point, hardness, dimensions and its temperature

range. Further technical data shall be provided as listed under the ‘datasheet’ column in Table A.3.

The product shall be designed to minimize stick debris on the ballast.
The mass of any piece of debris should be no greater than 5 g.
8 Packaging, labelling and storage
The packaging shall protect the contents from contamination and damage.
The labelling shall include at least the following:
— supplier’s name;
— brand name and/or code of the lubricant;
— batch number and date of manufacture, uncoded or coded;
— net mass/quantity/volume;
NOTE Local regulatory requirements will apply.

The following additional information shall be included if specified in the product specification:

— customer stock number;
— an indication that the batch has been accepted by the customer.

The storage conditions and, if necessary, the date limit of use of the lubricant shall be provided.

---------------------- Page: 13 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
Annex A
(normative)
Requirements for lubricants and testing
A.1 Explanation of Annex A: Tables A.1 to A.4
The tables have two purposes:
1) Tests to show the product can be used in the railway environment
NOTE Values can vary depending on where the material is used.
2) Product consistency

For each required property of the lubricants, Tables A.1, A.2 and A.3 list the mandatory and

optional tests for grease, oil and sticks respectively, and parameters for trainborne and trackside

applications. The optional tests required by the customer shall be listed in the product

specification. Although used, oil type lubricants have not been included for trackside applications

as the usage is low.

Table A.4 lists additional tests to check the performance characteristics of the lubricants and that

the lubricant will operate correctly with the equipment it’s to be used with.
A.2 Key to Annex A table columns ‘Type’, ‘Routine’ and ‘Datasheet’

The key to the columns ‘Type’, ‘Routine’ and ‘Technical Datasheet’ in Tables A.1 to A.4 is as

follows:

— ‘Type’ = This indicates the type tests required for the purpose of approval testing (see 6.1 and

6.2).

— ‘Routine’ = This indicates the routine tests required for testing from approved mass-

produced batches (see 6.3).

— ‘Technical Datasheet’ = This indicates the characteristics to be listed in the product

documentation.
In each column, a symbol is used to indicate the required test or information:
— ‘X’ indicates the test or piece of information is mandatory;
— ‘O’ indicates the test or piece of information is optional;
A.3 Key to Annex A table column ‘Use’

Tables A.1 to A.4 include a column headed ‘Use’ and the letters used mean the following:

— A = Trainborne using oil or grease type lubricants
— B = Trackside using grease type lubricants
— C = Trainborne using a solid lubricant
---------------------- Page: 14 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020

This column identifies the most common systems in current use. Most trainborne equipment

sprays the lubricant in the form of a free-flowing grease or thin oil and most trackside equipment

pumps it in the form of a thicker grease. However, where alternatives exist, careful consideration

to the tests required is needed.
---------------------- Page: 15 ----------------------
oSIST prEN 15427-2-1:2020
prEN 15427-2-1:2020
Table A.1 — Requirements for greases
Item Property Use Unit Test method Values Type Routine Datasheet Comments
A.1.1 Appearance A and - Visual Homogenous X X X Appearance is a general
B assessment of the product.
A.1.2 Colour A and - ISO 2049 Homogenous X O X
A.1.3 Consistency A - ISO 6743-99 Typically 00–000 X X X
B - ISO 6743-99 Typically 1 X X X
A.1.4.1 Un-worked grease A
penetration at:
a) 25 °C 0,1 mm ISO 2137 Typically 400 to 475 X O
b) 0 °C 0,1 mm ISO 13737 ≥ 350 X O
c) −25 °C 0,1 mm ISO 13737 ≥ 300 X O
A.1.4.2 Un-worked grease B
penetration at:
a) 25 °C 0
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.