SIST-TS CEN/TS 15234:2006
(Main)Solid biofuels - Fuel quality assurance
Solid biofuels - Fuel quality assurance
This Technical Specification defines the procedures to fulfil the quality requirements and describes measures to ensure adequate confidence that the biofuel specification is fulfilled. This Technical Specification covers the whole chain, from supply of raw materials to point of delivery to the end-user.
According to the mandate given for the standardisation work, the scope of the Technical Committee (TC 335) only includes solid biofuels originating from the following sources:
- products from agriculture and forestry;
- vegetable waste from agriculture and forestry;
- vegetable waste from the food processing industry;
- wood waste, with the exception of wood waste which may contain halogenated organic compounds or heavy metal as a result of treatment with wood preservatives or coating, and which includes in particular such wood waste originated from construction and demolition waste;
- fibrous vegetable waste from virgin pulp production and from the production of paper from pulp, if it is co-incinerated at the place of production and heat generated is recovered;
- cork waste.
NOTE 1: The quality assurance systems applied to the operation of conversion plants fuelled by solid biofuels are outside the scope of this Technical Specification.
NOTE 2: Health, safety and environmental issues for solid biofuels are important and need special attention, however are outside the scope of this Technical Specification.
NOTE 3: For the avoidance of doubt, demolition wood is not included in the scope of this Technical Specification. Demolition wood is defined as "used wood arising from demolition of buildings or civil engineering installations" (CEN/TS 14588).
Feste Biobrennstoffe - Qualitätssicherung von Brennstoffen
Diese Technische Spezifikation legt die Verfahren zur Erfüllung der Qualitätsanforderungen fest und be-
schreibt Maßnahmen zur Sicherstellung eines angemessenen Vertrauens auf die Einhaltung der Biobrenn-
stoffspezifikation. Diese Technische Spezifikation umfasst die gesamte Kette, von der Anlieferung der Roh-
stoffe bis zum Lieferort beim Endverbraucher.
Nach dem für die Normungsarbeit zugeteilten Mandat umfasst der Aufgabenbereich des Technischen
Komitees (TC 335) nur feste Biobrennstoffe, die aus folgenden Quellen stammen:
- Produkte aus der Land- und Forstwirtschaft;
- pflanzliche Abfälle aus der Land- und Forstwirtschaft;
- pflanzliche Abfälle aus der Lebensmittel verarbeitenden Industrie;
- Holzabfälle, mit der Ausnahme von Holzabfällen, die im Ergebnis der Behandlung mit Holzschutzmitteln
oder Aufbringung von Beschichtungen halogenierte organische Verbindungen oder Schwermetalle ent-
halten können, und zu denen besonders Holzabfälle gehören, die von Bau- und Abbrucharbeiten
stammen;
- faserige pflanzliche Abfälle aus der Herstellung von natürlichem Zellstoff und aus der Herstellung von Pa-
pier aus Zellstoff, sofern sie am Herstellungsort verbrannt werden und die erzeugte Wärme genutzt wird;
- Korkabfälle.
Biocombustibles solides - Assurance qualité du combustible
Trdna biogoriva – Zagotavljanje kakovosti goriv
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 15234:2006
01-maj-2006
Trdna biogoriva – Zagotavljanje kakovosti goriv
Solid biofuels - Fuel quality assurance
Feste Biobrennstoffe - Qualitätssicherung von Brennstoffen
Biocombustibles solides - Assurance qualité du combustible
Ta slovenski standard je istoveten z: CEN/TS 15234:2006
ICS:
75.160.10 Trda goriva Solid fuels
SIST-TS CEN/TS 15234:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 15234:2006
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 15234:2006
TECHNICAL SPECIFICATION
CEN/TS 15234
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
March 2006
ICS 75.160.10
English Version
Solid biofuels - Fuel quality assurance
Biocombustibles solides - Assurance qualité du Feste Biobrennstoffe - Qualitätssicherung von Brennstoffen
combustible
This Technical Specification (CEN/TS) was approved by CEN on 13 September 2005 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15234:2006: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
Contents Page
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .5
4 Symbols and abbreviations .7
5 Principle.8
6 Quality Assurance measures .9
7 Quality control measures.12
Annex A (Informative) Guidance for Quality Assurance of Solid Biofuels.18
Annex B (Informative) Examples on documentation for compliance with sub-clause 6.2
Production requirements .22
Annex C (Informative) Examples of Fuel Quality Declarations.36
Annex D (Informative) Example of a template for documentation of nonconformity.40
Annex E (Informative) Calculation of the net calorific value in different basis and energy density
as received .41
Bibliography .44
2
---------------------- Page: 4 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
Foreword
This Technical Specification (CEN/TS 15234:2006) has been prepared by Technical Committee CEN/TC 335
“Solid biofuels”, the secretariat of which is held by SIS.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
Introduction
The overall aim of this Technical Specification is to guarantee the solid biofuel quality through the whole
supply chain, from the origin to the delivery of the solid biofuel and provide adequate confidence that specified
quality requirements are fulfilled.
The solid biofuel supply chain usually consists of the main stages described in Figure 1.
End-user
Combustion
Raw
Identification Production/ Trade and Reception of
unit or
material
and collection of preparation of delivery of solid solid biofuel
other
raw material solid biofuels biofuels by end-user
conversion
unit
Supply chain activities covered by this Technical Specification
Figure 1—Solid biofuel supply chain
The objective of this Technical Specification is to serve as a tool to enable the efficient trading of biofuels.
Thereby:
[1] the end-user can find a biofuel that corresponds to his needs;
[2] the producer/supplier can produce a biofuel with defined and consistent properties and describe the
biofuel to the customers.
Quality assurance measures should establish confidence in the biofuel through systems that are simple to
operate and do not cause undue bureaucracy.
Solid biofuels are specified according to CEN/TS 14961—Solid Biofuels, Fuel Specification and Classes. Each
property specification requirement refers to a CEN Standard or a CEN Technical Specification. With a proper
quality assurance procedure and specification of origin and source (i.e. kind of biofuel) in the whole production
chain, it is possible to reduce or eliminate the parameters that need analysing.
[1]
According to the terminology of EN ISO 9001 a Quality Management system generally consist of Quality
Planning, Quality Control, Quality Assurance and Quality Improvement. This Technical Specification covers
Fuel Quality Assurance and Quality Control.
The users of this Technical Specification may integrate the CEN—Solid biofuels, Fuel Quality Assurance
[1, 2, 3]
Technical Specification in their general quality assurance scheme, e.g. the EN ISO 9000 series . If the
company does not have a quality management system, this Technical Specification can be used on it´s own to
help the supplier in documenting fuel quality and creating adequate confidence between the supplier and the
end-user.
In parallel to the preparation of this Technical Specification a Guide for Quality Assurance of Solid Biofuels
[8]
has produced as a CEN Technical Report .
This Technical Specification for Fuel Quality Assurance is only concerned with the fuel part. To ensure the
efficient use of solid biofuels, the relationship between the fuel and the combustion unit is also important to
consider. It is recommended that the end-users ensure that the combustion technology used and the solid
biofuels are compatible to achieve an optimised burning process. In addition to high efficiency, the
environmental impact is reduced when the combustion process is optimised (e.g. unburnt carbon in the ash
will be reduced; the emissions from the flue gases are reduced, etc.).
4
---------------------- Page: 6 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
1 Scope
This Technical Specification defines the procedures to fulfil the quality requirements and describes measures
to ensure adequate confidence that the biofuel specification is fulfilled. This Technical Specification covers the
whole chain, from supply of raw materials to point of delivery to the end-user.
According to the mandate given for the standardisation work, the scope of the Technical Committee (TC 335)
only includes solid biofuels originating from the following sources:
- products from agriculture and forestry;
- vegetable waste from agriculture and forestry;
- vegetable waste from the food processing industry;
- wood waste, with the exception of wood waste which may contain halogenated organic compounds or
heavy metal as a result of treatment with wood preservatives or coating, and which includes in particular
such wood waste originated from construction and demolition waste;
- fibrous vegetable waste from virgin pulp production and from the production of paper from pulp, if it is co-
incinerated at the place of production and heat generated is recovered;
- cork waste.
NOTE 1: The quality assurance systems applied to the operation of conversion plants fuelled by solid biofuels are outside
the scope of this Technical Specification.
NOTE 2: Health, safety and environmental issues for solid biofuels are important and need special attention, however are
outside the scope of this Technical Specification.
NOTE 3: For the avoidance of doubt, demolition wood is not included in the scope of this Technical Specification.
Demolition wood is defined as “used wood arising from demolition of buildings or civil engineering installations” (CEN/TS
14588).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
CEN/TS 14588:2003 Solid biofuels – Terminology, definitions and descriptions
CEN/TS 14961:2005 Solid biofuels – Fuel Specifications and classes
NOTE: In the CEN/TS 14961 there is a list (Table 3) of the CEN Technical Specifications for sampling,
sample reduction and determination of biofuel properties.
3 Terms and definitions
For the purposes of this Technical Specification, the terms and definitions given in the CEN /TS14588:2003
and the following apply.
5
---------------------- Page: 7 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
3.1
biomass resource owner
body or enterprise with the right to exploit the biomass resources for energy purposes
NOTE: The biomass resource owner can be a land or forest owner, a company etc.
3.2
chemical treatment
any treatment with chemicals other than air or water (e. g. glue and paint)
NOTE: See informative Annex D in the CEN/TS 14961:2005—Solid Biofuels, Fuel Specification and Classes.
3.3
critical control point
point within or between processes at which relevant properties can be most readily assessed and are also the
points that offer the greatest potential for quality improvement
3.4
customer
the next operator in the biofuel supply chain
3.5
delivery agreement
contract for fuel trade, which specifies e.g. origin and source, quality and quantity of the fuel, as well as
delivery terms
3.6
end-user
consumer (private person, enterprise, utility, etc.) using fuel for energy purposes
3.7
fuel quality declaration
document dated and signed by the producer/supplier to the retailer or end-user, specifying origin and source,
traded form and properties of defined lot
3.8
operator
body or enterprise, which is responsible for one or several activities in the solid biofuel supply chain
NOTE 1: The operator can be, for example, a biofuel producer or a subcontractor to the biofuel supplier.
NOTE 2: The first operator is a body or an enterprise which operates at the beginning of the supply chain.
3.9
point of delivery
the delivery location specified in the delivery agreement, at which the proprietary rights of and responsibility
for a fuel lot is transferred from the supplier to the end-user
3.10
producer
operator responsible for the production of the fuel or for any operation with the purpose of changing the biofuel
properties
NOTE: The producer can also be the supplier of the fuel.
3.11
quality
degree to which a set of inherent characteristics fulfils requirements
6
---------------------- Page: 8 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
3.12
quality assurance
part of quality management, focused on providing confidence that the quality requirements will be fulfilled
3.13
quality control
part of quality management, focused on fulfilling the quality requirements
3.14
retailer
supplier of (usually packaged) biofuels in (small) quantities to end-user
NOTE: Retailers are usually suppliers to the private household consumers.
3.15
supplier
operator responsible for supplying solid biofuels
NOTE: One supplier may deliver to the end-user directly and take responsibility for fuel deliveries from several
producers as well as delivery to the end-user.
3.16
supply chain
the overall process of handling and processing raw materials to the point of delivery to the end-user
4 Symbols and abbreviations
The symbols and abbreviations used in this Technical Specification comply with the SI—system of units as far
as possible.
d dry (dry basis)
daf dry, ash-free
ar as received
A Designation for ash content (w-% of dry basis)*
3
ρ Density [kg/m ]
3
BD Designation for bulk density [kg/m ]*
3
DE Designation for particle density as received [kg/dm ]*
D Designation for diameter [mm]*
DU Designation for mechanical durability [w-%]*
3
E Energy density as received [MWh/m loose, solid or stacked volume (amount of energy/volume unit)]
ar
3
E Designation for energy density as received [kWh/m or kWh/kg, unit is to be stated in brackets]*
F Designation for amount of fines (< 3,15 mm, w-%)
L Designation for length [mm]*
M Total moisture content as received [w-%] on wet basis
ar
7
---------------------- Page: 9 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
M Designation for moisture content as received [w-%]*
P Designation for particle size or particle size distribution [mm]*
q Gross calorific value at constant volume [MJ/kg]
,V,gr
q Net calorific value at constant pressure [MJ/kg]
p,net
*Designation symbols are used in combination with a number to specify property levels in Tables 4—13 and in
informative Annex A in the CEN/TS 14961:2005—Solid biofuels, Fuel Specifications and Classes. For
designation of chemical properties, chemical symbols like S (sulphur), Cl (chlorine), N (nitrogen) are used and
the value is added directly after the symbol.
5 Principle
This Technical Specification covers the Fuel Quality Assurance of the supply chain and the information to be
used in the quality control of the biofuel. This ensures traceability and gives confidence by demonstrating that
all processes along the supply chain (of solid biofuels) up to the point of the delivery to the end-user are under
control.
Procedures to establish confidence in the biofuel include the following requirements:
— first operator in the biofuel supply chain shall document the origin and source of the biofuel.
Origin and source refers to the kind of biofuel, as listed in Table 1 in the CEN/TS 14961:2005 (7.1);
— biofuel shall be traceable through the entire supply chain (7.1.2);
— biofuel producer shall take quality assurance measures to achieve and secure the fuel quality and the
company´s performance relating to the production and/or supply of the solid biofuels (6.2);
— transportation, handling and storage of the fuel should be performed with care and shall be documented by
the operator (6.3);
— supplier to the end-user or retailer is responsible for the biofuel quality and shall make a Fuel Quality
Declaration (6.4);
— for specifications in the Fuel Quality Declaration, CEN/TS 14961 shall be used. The Fuel Quality
Declaration shall include:
origin and source (7.1);
country where the biomass is harvested or first traded as biofuel (7.1.1);
traded form (7.2);
properties (7.3).
Figure 2 illustrates some of the different types of solid biofuel supply chains and appropriate points for
documenting the origin and source and the points for making the Fuel Quality Declaration. Additional
configurations of supply chains are possible.
8
---------------------- Page: 10 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
BIOMASS SUPPLIER END-USER
ORIGIN/SOURCE
Biofuels in bulk material
Biofuel
Operator or owner
producer
End-user
=supplier
Biomass
Operator
resource
owners
Biofuel Biofuel
End-user
producers supplier
Packaged biofuels
Biomass
Biofuel
Biofuel
Operator
resource End-user
producer/
retailer
owners
supplier
Documentation of
Fuel Quality Fuel Quality
origin and source
Declaration Declaration
CEN – Fuel Quality Assurance for solid biofuels
Figure 2 — Examples of the documentation of origin and source and Fuel Quality Declaration in
different biofuel supply chains
6 Quality Assurance measures
6.1 General
Quality Assurance aims to provide confidence that a stable quality is continually achieved in accordance with
the customer requirements. It means that specified requirements are fulfilled, but it does not necessarily mean
a high quality. Customer requirements include, beside a specified biofuel quality, also the quality of the
performance of the company relating to the biofuel or service (such as timing, logistics and proper
documentation). Fuel Quality Assurance needs to be applied to the entire supply chain (see Figure 1).
The methodology described in Clause 6 "Quality Assurance measures" facilitates the design of a fuel quality
system for producers and suppliers of solid biofuels. Its function is to make sure that:
traceability exists;
requirements that influence the fuel quality is controlled;
end-user can have confidence in the fuel quality.
9
---------------------- Page: 11 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
In sub-clauses: 6.2 Production requirements and 6.3 Transportation, handling and storage, both fuel quality
and company performance aspects, are covered. Sub-clause 6.4 covers the mandatory Fuel Quality
Declaration/labelling from the supplier.
Documentation is an important part of Quality Assurance. In this Technical Specification some documents are
mandatory while other documents are voluntary (see Table 1). For general guidance on “Quality Assurance
measures” see Informative Annex A.
Table 1—Mandatory documents on Quality Assurance measures
Area Mandatory documentation Sub-clause
a)
Traceability of raw material Documenting origin and source 7.1.2
b)
Production requirements Steps in the process chain (Step 1 ) 6.2
Critical Control Points (Step 4)
Criteria and methods to ensure appropriate control at
Critical Control Points (Step 5)
Nonconforming biofuels (Step 6)
Transportation, handling and Description of transportation, handling and storage 6.3
storage after production
Final fuel specification Fuel Quality Declaration/labelling 6.4
a
The producer of the solid biofuel from used wood or by-products and residues from the wood, herb or fruit processing industry
must ensure that the raw material used falls within the scope of the CEN/TS 14961.
b
The steps refer to the steps in the methodology described in sub-clause 6.2.
6.2 Production requirements
The production requirements for solid biofuels vary depending on the complexity of the production process as
well as on the requirements of the biofuel (for example between small-scale users that may require high-grade
biofuels and large-scale users who may take advantage of fuel flexible combustion units). This leads to
different measures and requirements for the Quality Assurance process. The methodology described below
for Quality Assurance of the production shall be used for all processes, but shall be adjusted for the
production requirements of the specific production chain in question.
Methodology for production quality assurance - step-by-step (see also Informative Annex A):
Step 1: Document the steps in the production chain;
Step 2: Define specification(s) for the biofuel(s);
Step 3: Analyse factors influencing fuel quality and company performance;
(This includes transportation, handling and storage see sub-clause 6.3)
Step 4: Identify and document the Critical Control Points for compliance with the fuel specification;
10
---------------------- Page: 12 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
Step 5: Select the appropriate measures that give confidence to customers that the specification(s)
is/are being realised, by:
identifying and documenting criteria and methods to ensure appropriate control of the
Critical Control Points;
monitoring and controlling the production process and making necessary adjustments for
compliance with the quality requirements.
Step 6: Establish and document routines for separate handling of nonconforming materials and biofuels.
If any deviation from the stated specification is noticed in the biofuel, the deviating part shall be
removed from this specific production chain if possible. If the deviating part cannot be taken
away, the producer shall inform the customer immediately and take the necessary corrective
actions. See informative Annex D for an example of a template on nonconformity.
All documents shall be dated and signed by the person assigned and authorised by the producer to do so. It
shall be available, on justified request, to the next customer in the production chain. In informative Annex B
there are some examples to illustrate the fulfilment of document requirements within production chains of
varying complexity.
NOTE: Detailed information like values of parameters in Critical Control Points are for internal use only.
6.3 Transportation, handling and storage
Suitable transportation, handling and storage are very important factors in the final quality of the biofuel. It also
ensures the fuel is kept in a correct environment. Negative influences on these operations should be avoided.
Transportation, handling and storage operations after biofuel production shall be documented by the operator.
This can for example be done in the delivery agreement.
Appropriate methods should be applied in the production, storage and delivery of the solid biofuels and care
should be exercised to avoid impurities and degradation in the fuel lot. Examples of impurities are stones,
pieces of metal, and plastic. Degradation can be caused by moisture absorption. Factors requiring special
attention:
weather and climatic conditions (e.g. risk of rain and snow) during storage and the need for covering;
storage conditions (e.g. ventilation, moisture absorption) and the foreseen duration of storage;
storage construction;
suitability and cleanliness of all equipment;
effects of transportation on the biofuels, e.g. formation of dust;
professional skills of personnel.
6.4 Fuel Quality Declaration and labelling
The Fuel Quality Declaration for the solid biofuel shall be issued by the producer/supplier to the end-user or
retailer. The Fuel Quality Declaration shall be issued for each defined lot. The quantity of the lot shall be
defined in the delivery agreement. The supplier shall date the declaration and keep the records for a minimum
of one year after the delivery. The Fuel Quality Declaration shall state the fuel quality in accordance to the
CEN/TS 14961. Fuel Quality Declarations shall be issued for both solid biofuels handled as bulk material and
for packaged solid biofuels.
11
---------------------- Page: 13 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
The Fuel Quality Declaration shall as a minimum include information on:
supplier (body or enterprise) including contact information;
a reference stating compliance to this Technical Specification;
origin and source (CEN/TS 14961:2005, Table 1);
country where the biomass is harvested or first traded as biofuel
traded form (CEN/TS 14961:2005, Table 2);
normative properties;
chemical treatment if chemically treated biomass is traded;
signature (assigned person), name, date and place.
A template example for a Fuel Quality Declaration (for solid biofuels) is given in informative Annex C1 and
examples of using this template are provided in the informative Annexes C2–C4.
For packaged solid biofuels, quality information shall be labelled on the packaging. Suitable storage conditions
shall also be required on the packaging.
7 Quality control measures
7.1 Specification of origin and source
7.1.1 General
Solid biofuels shall be specified by origin and source in accordance with the CEN/TS 14961:2005 Table 1.
The specification of origin and source shall be presented in the Fuel Quality Declaration described in sub-
clause 6.4. The CEN/TS 14961 allows the possibility to differentiate and specify solid biofuel with the detail
necessary. The supplier and end-user may agree on a more detailed specification of the kind of biofuel. In the
case of blends, origin and source of all fractions shall be stated.
Country/countries where the biomass is harvested or first traded as biofuel (by-products and residues from
wood, herb or fruit processing industry or used wood) shall be stated.
If more detailed information is requested it may be added in the Fuel Quality Declaration.
7.1.2 Traceability
All operators in the supply chain are responsible for the traceability of the origin and source of the material
delivered by them. Documents shall be completed in accordance with CEN/TS 14961:2005, Table 1.
The documents shall be available and provided on justified request throughout the entire supply chain. The
first operator in the supply chain is a body or enterprise, which operates at the beginning of the supply chain.
In the case of solid biofuels produced from by-products and residues from wood, herb or fruit processing
industries, the first operator is the industrial plant.
For used wood the first operator is the first owner who decides to trade or use it as a biofuel. The producer of
solid biofuels from used wood or by-products and residues from wood, herb or fruit processing industries is
responsible for the raw materials falls within the scope of the CEN/TS 14961.
12
---------------------- Page: 14 ----------------------
SIST-TS CEN/TS 15234:2006
CEN/TS 15234:2006 (E)
NOTE: When solid biofuels consist of a mixture from a number of first operators, all possible first operators should be
listed as the first operator.
7.2 Specification of traded forms
The traded form of the solid biofuel shall be specified. Table 2 in CEN/TS 14961:2005 shall be used unless
there is no traded form that the biofuel can be identified within. A supplier and end-user can agree upon a
more detailed description of the traded forms.
NOTE: Examples of traded forms are pellets, wood chips, straw bales etc.
7.3 Determination of properties
7.3.1 General
Properties shall be specified according to the requirements in Tables 4 – 13 in the CEN/TS 14961:2005. In
these tables properties are presented as grades. Normative and informative properties in these tables are
summarised in Table 2.
Determination of the properties is dependent on the type of information required and information available.
The supplier is responsible for the properties in the Fuel Quality Declaration.
If the properties being specified are sufficiently known through information about the origin and handling (or
preparation method combined with experience) then physical/chemical analysis may not be needed.
To minimise resources needed, one of the measures in the following order is recommended:
1) using typical values, e.g. laid down in Annex C of the CEN/TS 14961:2005, or obtained by
experience;
2) calculation of properties, e.g. by using typical values and considering documented specific values;
3) carrying out of analysis: a) with simplified methods if available, b) with reference methods.
The responsibility of the supplier to provide correct information in the Fuel Quality Declaration is exactly the
same whether laboratory analysis is performed or not.
If laboratory analysis is needed, sampling as well as physical and chemical analysis shall be performed
according to CEN Technical Specifications for Solid biofuels or methods referable to them.
NOTE 1: Seasonal variation should be taken into account and agreed between the supplier and end-user.
NOTE 2: Properties related to health and safety issues (e.g. smouldering and burning biofuels) are not covered in this
Technical Specification.
NOTE 3: Where any opera
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.