Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229:2010)

This International Standard specifies a method for the determination of the viscosity number (also known as reduced viscosity) and K-value of an unplasticized poly(vinyl chloride) (PVC) resin derived from a pipe, fitting or compound.
In this International Standard, only the method for isolation (or separation) of the PVC resin is detailed, while the determination of the viscosity number is given in ISO 1628-2.
The presence of other additives or polymers can invalidate this method (see Clause 3).

Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Rohre und Formstücke aus weichmacherfreiem Polyvinylchlorid (PVC-U) - Bestimmung der Viskositätszahl und Berechnung des K-Wertes (ISO 13229:2010)

Diese Internationale Norm legt ein Verfahren zur Bestimmung der Viskositätszahl (auch als reduzierte Viskosi-tät bezeichnet) und des K-Wertes eines weichmacherfreien Polyvinylchlorid-(PVC-)Harzes aus einem Rohr, Formstück oder Compound fest.
In dieser Internationalen Norm wird nur das Verfahren zur Abspaltung (oder Separation) des PVC-Harzes beschrieben, während die Bestimmung der Viskositätszahl in ISO 1628-2 angegeben ist.
Das Vorhandensein anderer Zusätze oder Polymere kann die Anwendung dieses Verfahrens ausschließen (siehe Abschnitt 3).

Systèmes de canalisations thermoplastiques pour applications sans pression - Tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) - Détermination de l'indice de viscosité réduite et de la valeur K (ISO 13229:2010)

L'ISO 13229:2010 spécifie une méthode de détermination de l'indice de viscosité (également appelé «viscosité réduite») et de la valeur K d'une résine de poly(chlorure  de vinyle) (PVC) non plastifié prélevée sur un tube, un raccord ou une composition.
Dans l'ISO 13229:2010, seule la méthode de séparation de la résine PVC est détaillée.

Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu - Cevi in fitingi iz nemehčanega polivinilklorida (PVC-U) - Ugotavljanje viskoznostnega števila in izračunavanje K-vrednosti (ISO 13229:2010)

Ta mednarodni standard določa metodo za ugotavljanje viskoznostnega števila (znanega tudi kot reducirane viskoznosti) in izračunavanje K-vrednosti nemehčane polivinilkloridne (PVC) smole, pridobljene iz cevi, fitinga ali zmesi.
V tem mednarodnem standardu je podrobno opisana le metoda za izolacijo (oziroma ločevanje) PVC-smole, ugotavljanje viskoznostnega števila pa je podano v ISO 1628-2.
Prisotnost drugih aditivov ali polimerov lahko to metodo razveljavi (glej točko 3).

General Information

Status
Published
Public Enquiry End Date
19-May-2011
Publication Date
08-Nov-2011
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
28-Oct-2011
Due Date
02-Jan-2012
Completion Date
09-Nov-2011

Relations

Buy Standard

Standard
EN ISO 13229:2011
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
k FprEN ISO 13229:2011
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 13229:2011
01-december-2011
1DGRPHãþD
SIST EN 922:1997
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORYNLGHOXMHMRSRWHåQRVWQHPSULQFLSX&HYLLQ
ILWLQJLL]QHPHKþDQHJDSROLYLQLONORULGD 39&8 8JRWDYOMDQMHYLVNR]QRVWQHJD
ãWHYLODLQL]UDþXQDYDQMH.YUHGQRVWL ,62
Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl
chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value
(ISO 13229:2010)
Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Rohre und
Formstücke aus weichmacherfreiem Polyvinylchlorid (PVC-U) - Bestimmung der
Viskositätszahl und Berechnung des K-Wertes (ISO 13229:2010)
Systèmes de canalisations thermoplastiques pour applications sans pression - Tubes et
raccords en poly(chlorure de vinyle) non plastifié (PVC-U) - Détermination de l'indice de
viscosité réduite et de la valeur K (ISO 13229:2010)
Ta slovenski standard je istoveten z: EN ISO 13229:2011
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
SIST EN ISO 13229:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 13229:2011

---------------------- Page: 2 ----------------------

SIST EN ISO 13229:2011


EUROPEAN STANDARD
EN ISO 13229

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2011
ICS 23.040.20; 91.140.80 Supersedes EN 922:1994
English Version
Thermoplastics piping systems for non-pressure applications -
Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings -
Determination of the viscosity number and K-value (ISO
13229:2010)
Systèmes de canalisations thermoplastiques pour Rohrleitungssysteme aus Thermoplasten für drucklose
applications sans pression - Tubes et raccords en Anwendungen - Rohre und Formstücke aus
poly(chlorure de vinyle) non plastifié (PVC-U) - weichmacherfreiem Polyvinylchlorid (PVC-U) - Bestimmung
Détermination de l'indice de viscosité réduite et de la valeur der Viskositätszahl und Berechnung des K-Wertes (ISO
K (ISO 13229:2010) 13229:2010)
This European Standard was approved by CEN on 11 August 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13229:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 13229:2011
EN ISO 13229:2011 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 13229:2011
EN ISO 13229:2011 (E)
Foreword
The text of ISO 13229:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings
and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 13229:2011 by Technical Committee CEN/TC 155 “Plastics piping systems and ducting
systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2012, and conflicting national standards shall be withdrawn at
the latest by March 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 922:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 13229:2010 has been approved by CEN as a EN ISO 13229:2011 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 13229:2011

---------------------- Page: 6 ----------------------

SIST EN ISO 13229:2011

INTERNATIONAL ISO
STANDARD 13229
First edition
2010-03-15

Thermoplastics piping systems for
non-pressure applications —
Unplasticized poly(vinyl chloride) (PVC-U)
pipes and fittings — Determination
of the viscosity number and K-value
Systèmes de canalisations thermoplastiques pour applications
sans pression — Tubes et raccords en poly(chlorure de vinyle)
non plastifié (PVC-U) — Détermination de l'indice de viscosité réduite
et de la valeur K




Reference number
ISO 13229:2010(E)
©
ISO 2010

---------------------- Page: 7 ----------------------

SIST EN ISO 13229:2011
ISO 13229:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 13229:2011
ISO 13229:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organiz
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Rohre und Formstücke aus weichmacherfreiem Polyvinylchlorid (PVC-U) - Bestimmung der Viskositätszahl und Berechnung des K-Wertes (ISO 13229:2010)Systèmes de canalisations thermoplastiques pour applications sans pression - Tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) - Détermination de l'indice de viscosité réduite et de la valeur K (ISO 13229:2010)Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229:2010)23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:FprEN ISO 13229kSIST FprEN ISO 13229:2011en01-april-2011kSIST FprEN ISO 13229:2011SLOVENSKI
STANDARD



kSIST FprEN ISO 13229:2011



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 13229
February 2011 ICS 23.040.20; 91.140.80 Will supersede EN 922:1994English Version
Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229:2010)
Systèmes de canalisations thermoplastiques pour applications sans pression - Tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) - Détermination de l'indice de viscosité réduite et de la valeur K (ISO 13229:2010)
Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Rohre und Formstücke aus weichmacherfreiem Polyvinylchlorid (PVC-U) -Bestimmung der Viskositätszahl und Berechnung des K-Wertes (ISO 13229:2010) This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 13229:2011: EkSIST FprEN ISO 13229:2011



FprEN ISO 13229:2011 (E) 2 Contents Page Foreword .3 kSIST FprEN ISO 13229:2011



FprEN ISO 13229:2011 (E) 3 Foreword The text of ISO 13229:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been taken over as FprEN ISO 13229:2011 by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 922:1994. Endorsement notice The text of ISO 13229:2010 has been approved by CEN as a FprEN ISO 13229:2011 without any modification.
kSIST FprEN ISO 13229:2011



kSIST FprEN ISO 13229:2011



Reference numberISO 13229:2010(E)© ISO 2010
INTERNATIONAL STANDARD ISO13229First edition2010-03-15Thermoplastics piping systems for non-pressure applications — Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings — Determination of the viscosity number and K-value Systèmes de canalisations thermoplastiques pour applications sans pression — Tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) — Détermination de l'indice de viscosité réduite et de la valeur K
kSIST FprEN ISO 13229:2011



ISO 13229:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii
© ISO 2010 – All rights reserved
kSIST FprEN ISO 13229:2011



ISO 13229:2010(E) © ISO 2010 – All rights reserved
iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.