SIST EN IEC 61010-2-030:2021/A11:2021

Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-030: Particular requirements for equipment having testing or measuring circuits

1   Scope and object
This clause of Part 1 is applicable except as follows:
1.1.1 Equipment included in scope
Replacement:
Replace the text with the following:
This group safety publication is primarily intended to be used as a product safety standard for the products mentioned in the scope, but shall also be used by technical committees in the preparation of their publications for products similar to those mentioned in the scope of this standard, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51.
This part of IEC 61010 specifies safety requirements for equipment having testing or measuring circuits which are connected for test or measurement purposes to devices or circuits outside the measurement equipment itself.
These include measuring circuits which are part of electrical test and measurement equipment, laboratory equipment, or process control equipment. The existence of these circuits in equipment requires additional protective means between the circuit and an OPERATOR.
NOTE These testing and measuring circuits can, for example:
–   measure voltages in circuits of other equipment,
–   measure temperature of a separate device via a thermocouple,
–   measure force on a separate device via a strain gauge,
–   inject a voltage onto a circuit to analyse a new design.
Equipment having these testing and measuring circuits may be intended for performing tests and measurements on hazardous conductors, including MAINS conductors and telecommunication network conductors. See Annex BB for considerations of HAZARDS involved in various tests and measurements.

Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2-030: Besondere Anforderungen für Geräte mit Prüf- oder Messstromkreis

[Not available]

Exigences de sécurité pour appareils électriques de mesurage, de régulation et de laboratoire - Partie 2-030: Exigences particulières pour les appareils équipés de circuits d’essai ou de mesure

Varnostne zahteve za električno opremo za meritve, nadzor in laboratorijsko uporabo - 2-030. del: Posebne zahteve za opremo s preskusnimi ali z merilnimi vezji- Dopolnilo 11

General Information

• Status: Published
• Public Enquiry End Date: 24-May-2020
• Publication Date: 01-Jun-2021
• ICS: 19.080 - Electrical and electronic testing
• ICS: 71.040.10 - Chemical laboratories. Laboratory equipment
• Technical Committee: MOV - Measuring equipment for electromagnetic quantities
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 14-Apr-2021
• Due Date: 19-Jun-2021
• Completion Date: 02-Jun-2021
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Mandate: M/511 - Mandate to CEN, CENELEC and ETSI relating to harmonised standards in the field of the Low Voltage Directive
• Ref Project: EN IEC 61010-2-030:2021/A11:2021 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-030: Particular requirements for equipment having testing or measuring circuits

Relations

• Amends: SIST EN IEC 61010-2-030:2021 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-030: Particular requirements for equipment having testing or measuring circuits (IEC 61010-2-030:2017)
• Effective Date: 15-Apr-2021
• Revised: kSIST FprEN IEC 61010-2-030:2023 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-030: Particular requirements for equipment having testing or measuring circuits
• Effective Date: 24-May-2022

Overview

SIST EN IEC 61010-2-030:2021/A11:2021 is a critical European standard published by the European Committee for Electrotechnical Standardization (CLC). It specifies the safety requirements for electrical equipment used in measurement, control, and laboratory environments, focusing specifically on equipment with testing or measuring circuits. These circuits connect to devices or circuits external to the measurement equipment itself, necessitating enhanced protective measures to ensure operator safety.

This standard is an amendment to EN IEC 61010-2-030:2021 and aligns with IEC Guide 104 and ISO/IEC Guide 51 to provide guidance on product safety while supporting compliance with the EU Low Voltage Directive 2014/35/EU.

Key Topics

• Scope and Object
  This standard applies primarily to electrical equipment used for test or measurement purposes in laboratory, process control, or electrical test equipment contexts. It includes:

  • Measuring circuits that assess voltages in other equipment
  • Devices measuring physical parameters like temperature or force through sensors such as thermocouples or strain gauges
  • Equipment capable of injecting test voltages for design analysis
    The standard recognizes that such equipment may interact with potentially hazardous conductors, including mains electricity and telecommunication networks.

• Safety Requirements
  Specific protective measures are outlined, such as regulated test voltages maintaining ±5% accuracy during AC and DC voltage tests. The standard also addresses insulation materials and life expectancy considerations for manufacturers.

• Amendments & Annexes
  The amendment introduces modifications to voltage test procedures and adds normative references aligning with other international and European publications. Informative annexes clarify the relationship with EU safety directives and harmonization expectations.

• Compliance and Conformity
  EN IEC 61010-2-030:2021/A11 provides a presumption of conformity with the essential safety objectives of the EU Low Voltage Directive 2014/35/EU. This facilitates market access across EU member states through harmonized safety practices.

Applications

This standard is indispensable for manufacturers, technical committees, and safety engineers involved in the design, production, or certification of electrical equipment used for:

• Electrical test and measurement instruments
• Laboratory testing equipment
• Process control and automation systems
• Devices with circuits measuring or testing external signals

Equipment conforming to EN IEC 61010-2-030:2021/A11 is designed to protect operators from electrical hazards, mechanical failures, and environmental influences, ensuring safe and reliable operation in complex measurement setups involving hazardous voltages or currents.

Related Standards

• IEC 61010-1: General safety requirements for electrical equipment for measurement, control, and laboratory use
• EN IEC 61010-2-032: Particular requirements for hand-held and hand-manipulated current sensors
• EU Directive 2014/35/EU: Harmonizing electrical equipment safety across Europe
• IEC Guide 104 & ISO/IEC Guide 51: General principles for product safety standards development

Practical Value

Implementing EN IEC 61010-2-030:2021/A11 ensures:

• Enhanced protection against electrical shock and hazardous operating conditions
• Compliance with European market access requirements thanks to harmonized safety criteria
• Standardized testing procedures that improve product reliability and operator safety
• Clear guidance for manufacturers on insulation materials and test methods aligned with expected equipment lifetime
• Integration of environmental and mechanical resistance criteria to prevent equipment failure during use

Manufacturers and compliance professionals seeking to align test and measurement equipment with stringent European safety laws will find this standard essential in achieving robust, market-ready products.

---

Keywords: EN IEC 61010-2-030:2021/A11, electrical equipment safety, measurement circuits, laboratory equipment safety, test and measurement devices, electrical safety standards, Low Voltage Directive, CLC standard, electronic test equipment, electrical test safety requirements.

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2021
Varnostne zahteve za električno opremo za meritve, nadzor in laboratorijsko
uporabo - 2-030. del: Posebne zahteve za opremo s preskusnimi ali z merilnimi
vezji- Dopolnilo 11
Safety requirements for electrical equipment for measurement, control, and laboratory
use - Part 2-030: Particular requirements for equipment having testing or measuring
circuits
Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2
-030: Besondere Anforderungen für Geräte mit Prüf- oder Messstromkreis
Exigences de sécurité pour appareils électriques de mesurage, de régulation et de
laboratoire - Partie 2-030: Exigences particulières pour les appareils équipés de circuits
d’essai ou de mesure
Ta slovenski standard je istoveten z: EN IEC 61010-2-030:2021/A11:2021
ICS:
19.080 Električno in elektronsko Electrical and electronic
preskušanje testing
71.040.10 Kemijski laboratoriji. Chemical laboratories.
Laboratorijska oprema Laboratory equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61010-2-030:2021/A11

NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2021
ICS 19.080; 71.040.10
English Version
Safety requirements for electrical equipment for measurement,
control, and laboratory use - Part 2-030: Particular requirements
for equipment having testing or measuring circuits
Exigences de sécurité pour appareils électriques de Sicherheitsbestimmungen für elektrische Mess-, Steuer-,
mesurage, de régulation et de laboratoire - Partie 2-030: Regel- und Laborgeräte - Teil 2-030: Besondere
Exigences particulières pour les appareils équipés de Anforderungen für Geräte mit Prüf- oder Messstromkreis
circuits d'essai ou de mesure
This amendment A11 modifies the European Standard FprEN 61010-2-030:2016; it was approved by CENELEC on 2021-03-08. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61010-2-030:2021/A11:2021 E

European foreword
This document (EN IEC 61010-2-030:2021/A11:2021) has been prepared by CLC/TC 66X “Safety of
measuring, control, and laboratory equipment”.
The following dates are fixed:
• latest date by which this document has (dop) 2021-10-02
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2024-04-02
standards conflicting with this document
have to be withdrawn
This document amends EN IEC 61010-2-030:2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
1 Modification to 6.8.3.1, “The a.c. voltage test”
Replace the first sentence of the first paragraph with the following sentence:
“The voltage tester shall have a regulated output capable of maintaining the test voltage throughout the
test within ± 5% of the specified value.”
2 Modification to 6.8.3.2, “The d.c. voltage test”
Add a new sentence at the beginning of the first paragraph:
“The voltage tester shall have a regulated output capable of maintaining the test voltage throughout the
test within ± 5% of the specified value.”
3 Modifications to K.101.4.1, “General”
Replace the second paragraph with the following note:
"
NOTE 1 The manufacturer is supposed to take the expected life of the equipment into account when selecting
insulating materials.”
As a result of this, renumber the existing note as NOTE 2.
4 Addition of Annex ZA, “Normative references to international publications
...