Small craft - Quick release system for trapeze harness (ISO 10862:2009)

This International Standard specifies requirements and test methods for quick release devices as a component of the small sailing-craft trapeze system worn whilst afloat. The quick release device is intended to quickly release the wearer from entrapment and minimize the risk of drowning in the event of a failure to release from the sailing-craft trapeze system by other means. The quick release device is intended to be easily accessible and operated in all conditions that might occur whilst in use, including when a craft is capsized or inverted.

Kleine Wasserfahrzeuge - Schnellöffnungssysteme für Trapezgurte (ISO 10862:2009)

Diese Internationale Norm legt allgemeine Anforderungen und Prüfverfahren für Vorrichtungen zur Schnellauslösung
für Trapezgurte fest, die Teil eines Trapezsystems für kleine Segelboote sind und auf See getragen
werden. Die Schnellauslösevorrichtung für Trapezgurte ist dafür vorgesehen, seinen Träger schnell aus einer
Fangstellung zu befreien und das Risiko des Ertrinkens zu minimieren, wenn es misslingt, sich auf anderem
Wege von einem Trapezsystem für Segelboote zu befreien.
Die Schnellauslösevorrichtung sollte leicht erreichbar und unter allen Bedingungen, die im Laufe ihres Einsatzes
auftreten könnten, einschließlich Kenterns oder Umdrehens des Bootes, bedienbar sein.

Petits navires - Systeme de largage rapide pour harnais de trapeze (ISO 10862:2009)

L'ISO 10862:2009 spécifie les exigences et les méthodes d'essai relatives au système de largage rapide utilisé comme élément du système de harnais de trapèze de voilier, et porté lorsque le bateau est à flot. Le système de largage rapide est destiné à protéger le porteur contre son blocage sous l'eau et sa noyade dans le cas où il n'a pas pu se libérer du système de trapèze par d'autres moyens.
Le système de largage rapide est prévu pour être facilement accessible et utilisé dans toutes les conditions que l'on peut rencontrer lors de son utilisation, y compris lorsque le bateau est chaviré ou inversé.

Mala plovila - Sistem hitrega odpenjanja trapeznih pasov (ISO 10862:2009)

General Information

Status
Published
Public Enquiry End Date
14-Jan-2008
Publication Date
17-Nov-2009
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-Sep-2009
Due Date
20-Nov-2009
Completion Date
18-Nov-2009

Buy Standard

Standard
EN ISO 10862:2009
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10862:2009
01-december-2009
Mala plovila - Sistem hitrega odpenjanja trapeznih pasov (ISO 10862:2009)
Small craft - Quick release system for trapeze harness (ISO 10862:2009)
Kleine Wasserfahrzeuge - Schnellöffnungssysteme für Trapezgurte (ISO 10862:2009)
Petits navires - Systeme de largage rapide pour harnais de trapeze (ISO 10862:2009)
Ta slovenski standard je istoveten z: EN ISO 10862:2009
ICS:
13.340.60 =DãþLWDSUHGSDGFLLQ]GUVL Protection against falling and
slipping
47.080 ýROQL Small craft
SIST EN ISO 10862:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10862:2009

---------------------- Page: 2 ----------------------

SIST EN ISO 10862:2009
EUROPEAN STANDARD
EN ISO 10862
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2009
ICS 47.080
English Version
Small craft - Quick release system for trapeze harness (ISO
10862:2009)
Petits navires - Système de largage rapide pour harnais de Kleine Wasserfahrzeuge - Schnellöffnungssysteme für
trapèze (ISO 10862:2009) Trapezgurte (ISO 10862:2009)
This European Standard was approved by CEN on 20 May 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10862:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 10862:2009
EN ISO 10862:2009 (E)
Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 89/686/EC .4

2

---------------------- Page: 4 ----------------------

SIST EN ISO 10862:2009
EN ISO 10862:2009 (E)
Foreword
This document (EN ISO 10862:2009) has been prepared by Technical Committee ISO/TC 188 "Small craft" in
collaboration with Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection
and lifejackets” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2009, and conflicting national standards shall be withdrawn
at the latest by December 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive.
For relationship with EC Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10862:2009 has been approved by CEN as a EN ISO 10862:2009 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 10862:2009
EN ISO 10862:2009 (E)
Annex ZA
(informative)

Relationship between this European Standard and the Essential
Requirements of EU Directive 89/686/EC
This standard has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association to provide a means of conforming to Essential Requirements of the New
Approach Directive 89/686/EEC on the approximation of the laws of the Member States relating to personal
protective equipment.

Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the clauses of this
standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of
conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations.


Table ZA.1 — Correspondence between this standard and Directive 89/686/EEC

Clause(s)/sub-clause(s) Essential Requirements (ERs) of Directive Qualifying remarks/Notes
of this EN 89/686/EEC
4.1, 4.3 1.2.1  Absence of risk and other “inherent”
      nuisance factors
4.12 1.3.2  Lightness and design strength
4.1 1.3.3  Compatibility of PPE for simultaneous
      use
7 1.4   Information supplied by the manufacturer
6b) 2.4   PPE subject to ageing
4.1, 4.2, 4.4 to 4.7, 4.9 2.7   PPE intended for rapid installation
4.1, 6, 7 2.10  PPE for connection to another, external
     complementary device
4.2, 6 2.12  PPE bearing one or more identification
     or recognition marks directly or indirectly
     relating to health and safety


WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.

4

---------------------- Page: 6 ----------------------

SIST EN ISO 10862:2009

INTERNATIONAL ISO
STANDARD 10862
First edition
2009-06-15


Small craft — Quick release system for
trapeze harness
Petits navires — Système de largage rapide pour harnais de trapèze





Reference number
ISO 10862:2009(E)
©
ISO 2009

---------------------- Page: 7 ----------------------

SIST EN ISO 10862:2009
ISO 10862:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 10862:2009
ISO 10862:2009(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Requirements . 2
4.1 General. 2
4.2 Identification. 3
4.3 Inadvertent release or disconnection. 3
4.4 Overload . 3
4.5 Dynamic load. 3
4.6 Operation in-line . 4
4.7 No-load. 4
4.8 Operation out of line. 4
4.9 Re-arming . 4
4.10 Resistance to debris. 4
4.11 Resistance to salt water. 4
4.12 Resistance to corrosion. 4
5 Test methods. 4
5.1 General. 4
5.2 Sampling. 5
5.3 Overload test . 5
5.4 Operation in-line tests. 7
5.5 Re-arming test. 9
5.6 Operation out-of-line tests. 9
5.7 Inadvertent release test. 10
5.8 Debris test . 11
5.9 Salt water test. 11
5.10 Corrosion test . 11
6 Marking . 11
7 Information supplied by the manufacturer . 11

© ISO 2009 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 10862:2009
ISO 10862:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10862 was prepared by Technical Committee ISO/TC 188, Small craft, in collaboration with Technical
Committee CEN/TC 162, Protective clothing including hand and arm protection and lifejackets, in accordance
with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
iv © ISO 2009 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 10862:2009
ISO 10862:2009(E)
Introduction
Many people actively participate in small craft sailing with little evidence of accident, injury or death.
Statistically, sailing is one of the safer leisure activities. There are, however, a very few documented accounts
of injury and death owing to a participant being entrapped underwater as a result of not being able to detach
themselves from the craft and, in some cases, not being able to release themselves from a sailing-craft
trapeze.
This International Standard has been developed jointly by recreational-craft user groups and industry in an
endeavour to reduce the possibility of entrapment underwater as a result of the inability of the user to release
from a sailing-craft trapeze.
The scope of this International Standard is intentionally restricted and only covers the functioning of the safety
release device of small sailing-craft trapeze systems. When developing this International Standard,
ISO/TC 188/WG 14 emphasized that the safety of a craft and her entire management is the sole responsibility
of the person in charge, who will also ensure that the craft and crew are adequate to face the conditions that
might arise in the course of use. The establishment of this International Standard in no way limits or reduces
the absolute responsibility of the person in charge and their responsibility for the crew, the craft and the
management thereof.

© ISO 2009 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 10862:2009

---------------------- Page: 12 ----------------------

SIST EN ISO 10862:2009
INTERNATIONAL STANDARD ISO 10862:2009(E)

Small craft — Quick release system for trapeze harness
1 Scope
This International Standard specifies requirements and test methods for quick release devices as a
component of the small sailing-craft trapeze system worn whilst afloat. The quick release device is intended to
quickly release the wearer from entrapment and minimize the risk of drowning in the event of a failure to
release from the sailing-craft trapeze system by other means.
The quick release device is intended to be easily accessible and operated in all conditions that might occur
whilst in use, including when a craft is capsized or inverted.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 9227, Corrosion tests in artificial atmospheres — Salt spray tests
EN 364:1992, Personal protective equipment against falls from a height — Test methods
EN 892:2004, Mountaineering equipment — Dynamic mountaineering ropes — Safety requirements and test
methods
EN 13139:2002, Aggregates for mortar
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
sailing-craft trapeze system
system of sailing-craft equipment and/or devices attached to a craft and user which can be used to support
the main body mass of that user, thereby enabling an increase in the righting moment (through their body
mass) on the craft
3.2
user's attachment point
point to which the trapeze system tensile load is applied and which connects and disconnects the user to and
from the craft when the system is in normal use
3.3
release attachment point
point to which the trapeze system tensile load is applied and from which the user is released from the craft
when the release system is activated
NOTE In any particular trapeze system, the release attachment point might be the same as, or may be additional to,
the user's attachment point.
© ISO 2009 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 10862:2009
ISO 10862:2009(E)
3.4
quick release device
mechanism, device, etc. that brings about the intentional immediate release and separation of the release
attachment point under critical emergency load conditions
3.5
user main attachment fitting
user attachment fitting
attachment, fitting or device possessing the user main attachment point and which, in normal use, remains
with the user after disconnection
3.6
craft main attachment fitting
craft attachment fitting
attachment, fitting or device possessing the craft main attachment point and which, in normal use, remains
with the craft after disconnection
3.7
standard craft main attachment fitting
standard craft attachment fitting
ring used as the craft main attachment fitting in cases of non-exclusively-compatible attachment fittings
3.8
harness
textile assembly worn by the user, to which is attached that part of the user main attachment fitting that
remains with the user after disconnection
3.9
manufacturer's specified operational mass range
range specified by the manufacturer giving the user's minimum and maximum operational mass (the mass of
the user ready to sail, equipped with trapeze harness, footwear, wetsuit, flotation device, etc.)
4 Requirements
4.1 General
The quick release device design shall have the aim of releasing the user from the craft main attachment fitting
within 5 s.
The quick release device shall be simple to use and capable of operation with one gloved hand. Operation of
the quick release device shall not present any significant risk to the user.
After all the tests described in Clause 5 have been carried out, the quick release device shall still be capable
of correct operation and releasing the user from the main attachment fitting within 5 s.
User and craft main attachment fittings may or may not be exclusively-compatible with each other.
Exclusively-compatible main attachment fittings shall only be used together and shall not be used with other
designs. Non-exclusively-compatible main attachment fittings are not exclusive to each other, i.e. the user
main attachment fitting (hereinafter referred to as “user attachment fitting”) may be used with the craft main
attachment fitting (hereinafter referred to as “craft attachment fitting”) of a common design similar in shape
and application to the standard craft attachment fitting (see Figure 1). The manufacturer of equipment fitted
with
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.