Quality management - Requirements for measurement management systems (ISO/DIS 10012:2024)

ISO 10012:2003 specifies generic requirements and provides guidance for the management of measurement processes and metrological confirmation of measuring equipment used to support and demonstrate compliance with metrological requirements. It specifies quality management requirements of a measurement management system that can be used by an organization performing measurements as part of the overall management system, and to ensure metrological requirements are met.
ISO 10012:2003 is not intended to be used as a requisite for demonstrating conformance with ISO 9001, ISO 14001 or any other standard. Interested parties can agree to use ISO 10012:2003 as an input for satisfying measurement management system requirements in certification activities. Other standards and guides exist for particular elements affecting measurement results, for example, details of measurement methods, competence of personnel, interlaboratory comparisons.
ISO 10012:2003 is not intended as a substitute for, or as an addition to, the requirements of ISO/IEC 17025.

Qualitätsmanagement - Anforderungen an Messmanagementsysteme (ISO/DIS 10012:2024)

Management de la qualité - Exigences pour les systèmes de management de la mesure (ISO/DIS 10012:2024)

L'ISO 10012:2003 est destinée à fournir des exigences génériques et des guides d'application pour le management des processus de mesure et pour la confirmation des équipements de mesure utilisés pour démontrer la conformité aux exigences métrologiques. Elle spécifie les exigences qualité relatives au système de management de la mesure qu'un organisme effectuant des mesures peut utiliser et intégrer dans le cadre du système de management global et qui est destiné à garantir que les exigences métrologiques sont satisfaites.
L'ISO 10012:2003 n'est pas destinée à être requise pour démontrer la conformité avec l'ISO 9001, avec l'ISO 14001 ou avec toute autre norme. Les parties intéressées peuvent convenir d'utiliser la présente Norme internationale comme point d'entrée à la satisfaction des exigences relatives au système de management de la mesure dans des activités de certification.
L'ISO 10012:2003 n'est destinée ni à être substituée ni à être ajoutée aux exigences de l'ISO/IEC 17025.

Vodenje kakovosti - Zahteve za sisteme vodenja meritev (ISO/DIS 10012:2024)

General Information

Status
Not Published
Public Enquiry End Date
22-Dec-2024
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
09-Oct-2024
Due Date
26-Feb-2025

Relations

Buy Standard

Draft
prEN ISO 10012:2024 - BARVE
English language
54 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2024
Vodenje kakovosti - Zahteve za sisteme vodenja meritev (ISO/DIS 10012:2024)
Quality management - Requirements for measurement management systems (ISO/DIS
10012:2024)
Qualitätsmanagement - Anforderungen an Messmanagementsysteme (ISO/DIS
10012:2024)
Management de la qualité - Exigences pour les systèmes de management de la mesure
(ISO/DIS 10012:2024)
Ta slovenski standard je istoveten z: prEN ISO 10012
ICS:
03.100.70 Sistemi vodenja Management systems
03.120.10 Vodenje in zagotavljanje Quality management and
kakovosti quality assurance
17.020 Meroslovje in merjenje na Metrology and measurement
splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
International
Standard
ISO/DIS 10012
ISO/TC 176/SC 3
Quality management –
Secretariat: SA
Requirements for measurement
Voting begins on:
management systems
2024-09-25
Management de la qualité — Exigences pour les systèmes de
Voting terminates on:
management de la mesure
2024-12-18
ICS: 17.020; 03.100.70
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 10012:2024(en)
DRAFT
ISO/DIS 10012:2024(en)
International
Standard
ISO/DIS 10012
ISO/TC 176/SC 3
Quality Management –
Secretariat: SA
Requirements for Measurement
Voting begins on:
Management Systems
Management de la qualité - Exigences pour les systèmes de
Voting terminates on:
management de la mesure
ICS: 17.020; 03.100.70
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 10012:2024(en)
ii
ISO/DIS 10012:2024(en)
ISO 10012:2023(X)
Contents
Foreword . vi
Introduction . vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Context of the organization . 6
4.1 Understanding the organization and its context . 6
4.2 Understanding the needs and expectations of interested parties . 6
4.3 Determining the scope of the measurement management system. 6
4.4 Measurement management system . 7
5 Leadership . 7
5.1 Leadership and commitment . 7
5.1.1 General . 7
5.1.2 Interested party focus . 8
5.2 Measurement management policy . 8
5.3 Roles, responsibilities and authorities . 8
6 Planning . 9
6.1 Actions to address risks and opportunities . 9
6.2 Measurement management objectives and planning to achieve them . 9
6.3 Planning of changes . 10
7 Support . 10
7.1 Resources . 10
7.1.1 General . 10
7.1.2 Personnel . 10
7.1.3 Environment and facilities . 10
7.1.4 Equipment . 11
7.1.5 Organizational knowledge . 11
7.2 Competence . 11
7.3 Awareness . 12
7.4 Communication. 12
7.5 Documented information . 13
7.5.1 General . 13
7.5.2 Creating and updating documented information . 13
7.5.3 Control of documented information . 13
8 Operation . 14
8.1 Operational planning and control . 14
8.1.1 General . 14
8.1.2 Risk management . 14
8.2 Requirements for measurement processes . 15
8.2.1 General . 15
8.2.2 Customer communications . 15
8.2.3 Determination of requirements related to the measurement processes . 15
8.2.4 Review of customer requirements for measurement processes . 16
8.2.5 Changes to requirements for measurement processes . 16
8.3 Design and development of measurement processes . 16
8.3.1 General . 16
8.3.2 Design and development planning . 17

© ISO 10012 – All rights reserved iii
iii
ISO/DIS 10012:2024(en)
ISO 10012:2023(X)
8.3.3 Design and development inputs .18
8.3.4 Design and development controls .19
8.3.5 Design and development outputs .20
8.3.6 Design and development changes .22
8.4 Control of externally provided processes, products and services .22
8.4.1 General .22
8.4.2 Type and extent of control .23
8.4.3 Information for external providers .24
8.5 Measurement process implementation .24
8.5.1 Control of measurement processes .24
8.5.2 Identification and traceability .26
8.5.3 Property belonging to customers or external providers .27
8.5.4 Preservation.27
8.5.5 Measurement process post-delivery activities .27
8.6 Release of measurement process results .28
8.6.1 Planned arrangements for release of results .28
8.6.2 Documented information relating to release of results .28
8.7 Control of non-conforming outputs .29
8.7.1 Handling nonconforming outputs .29
8.7.2 Documented information .30
9 Performance evaluation .30
9.1 Monitoring, measurement, analysis, and evaluation .30
9.1.1 General .30
9.1.2 Customer satisfaction .30
9.1.3 Analysis and evaluation .30
9.2 Internal audit .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.