iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 286-4:1998

(Main)

Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium alloy pressure vessels designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock

Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium alloy pressure vessels designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock

This Part of this European Standard is applicable to simple unfired steel pressure vessels, referred to as "vessel" in this standard, designed for air braking equipment and auxiliary pneumatic equipment for railway rollingstock.

Einfache unbefeuerte Druckbehälter für Luft oder Stickstoff - Teil 4: Druckbehälter aus Aluminiumlegierungen für Druckbremsanlagen und pneumatische Hilfseinrichtungen in Schienenfahrzeugen

Dieser Teil dieser Europäischen Norm gilt für einfache Druckbehälter aus Aluminiumlegierungen, unbefeuert, nachfolgend als "Behälter" bezeichnet, für Druckluftbremsanlagen und pneumatischen Hilfseinrichtungen in Schienenfahrzeugen.

Récipients a pression simples, non soumis a la flamme, destinés a contenir de l'air ou de l'azote - Partie 4: Récipients a pression en alliages d'aluminium destinés aux équipements pneumatiques de freinage et aux équipements pneumatiques auxiliaires du matériel roulant ferroviaire

La présente partie de cette norme européenne s'applique aux récipients a pression simples en alliages d'aluminium, non soumis a la flamme, dénommés "réservoir" dans la présente norme, destinés aux équipements a air de freinage et aux équipements auxiliaires pneumatiques du matériel roulant ferroviaire.

Enostavne, neogrevane tlačne posode, namenjene za zrak ali dušik - 4. del: Tlačne posode iz aluminijevih zlitin za zračne zavore in pomožno pnevmatsko opremo na tirnih vozilih

General Information

Status
Published
Publication Date
30-Sep-1998
ICS
23.020.32 - Pressure vessels
77.150.10 - Aluminium products
Technical Committee
TLP - Pressure vessels
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Oct-1998
Due Date
01-Oct-1998
Completion Date
01-Oct-1998
Directive
2009/105//EC - DIRECTIVE 2009/105/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 16 September 2009 relating to simple pressure vessels
87/404/EEC - Simple pressure vessels
TP071 - Pravilnik o tehnični skladnosti tirnih vozil
TP101 - Pravilnik o zavorah, varnostnih napravah in opremi železniških vozil
Mandate
M/BC/CEN/86/6 - Standardization request to CEN concerning simple unfired pressure vessels
Ref Project
EN 286-4:1994 - Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium alloy pressure vessels designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock

Relations

Revises
kSIST FprEN 286-4:2022 - Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium alloy pressure vessels designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock
Effective Date
18-Jan-2023
Revises
kSIST FprEN 286-4:2022 - Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium alloy pressure vessels designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock
Effective Date
19-Jan-2023
Revised
kSIST FprEN 286-4:2022 - Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium alloy pressure vessels designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock
Effective Date
01-Nov-2019

Buy Standard

EN 286-4:1998EN 286-4:1998
PreviousNext
Standard
EN 286-4:1998
English language
67 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 286-4:1998
01-oktober-1998
(QRVWDYQHQHRJUHYDQHWODþQHSRVRGHQDPHQMHQH]D]UDNDOLGXãLNGHO7ODþQH
SRVRGHL]DOXPLQLMHYLK]OLWLQ]D]UDþQH]DYRUHLQSRPRåQRSQHYPDWVNRRSUHPRQD
WLUQLKYR]LOLK
Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium
alloy pressure vessels designed for air braking equipment and auxiliary pneumatic
equipment for railway rolling stock
Einfache unbefeuerte Druckbehälter für Luft oder Stickstoff - Teil 4: Druckbehälter aus
Aluminiumlegierungen für Druckbremsanlagen und pneumatische Hilfseinrichtungen in
Schienenfahrzeugen
Récipients a pression simples, non soumis a la flamme, destinés a contenir de l'air ou de
l'azote - Partie 4: Récipients a pression en alliages d'aluminium destinés aux
équipements pneumatiques de freinage et aux équipements pneumatiques auxiliaires du
matériel roulant ferroviaire
Ta slovenski standard je istoveten z: EN 286-4:1994
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 286-4:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 286-4:1998

---------------------- Page: 2 ----------------------

SIST EN 286-4:1998

---------------------- Page: 3 ----------------------

SIST EN 286-4:1998

---------------------- Page: 4 ----------------------

SIST EN 286-4:1998

---------------------- Page: 5 ----------------------

SIST EN 286-4:1998

---------------------- Page: 6 ----------------------

SIST EN 286-4:1998

---------------------- Page: 7 ----------------------

SIST EN 286-4:1998

---------------------- Page: 8 ----------------------

SIST EN 286-4:1998

---------------------- Page: 9 ----------------------

SIST EN 286-4:1998

---------------------- Page: 10 ----------------------

SIST EN 286-4:1998

---------------------- Page: 11 ----------------------

SIST EN 286-4:1998

---------------------- Page: 12 ----------------------

SIST EN 286-4:1998

---------------------- Page: 13 ----------------------

SIST EN 286-4:1998

---------------------- Page: 14 ----------------------

SIST EN 286-4:1998

---------------------- Page: 15 ----------------------

SIST EN 286-4:1998

---------------------- Page: 16 ----------------------

SIST EN 286-4:1998

---------------------- Page: 17 ----------------------

SIST EN 286-4:1998

---------------------- Page: 18 ----------------------

SIST EN 286-4:1998

---------------------- Page: 19 ----------------------

SIST EN 286-4:1998

---------------------- Page: 20 ----------------------

SIST EN 286-4:1998

---------------------- Page: 21 ----------------------

SIST EN 286-4:1998

---------------------- Page: 22 ----------------------

SIST EN 286-4:1998

---------------------- Page: 23 ----------------------

SIST EN 286-4:1998

---------------------- Page: 24 ----------------------

SIST EN 286-4:1998

---------------------- Page: 25 ----------------------

SIST EN 286-4:1998

---------------------- Page: 26 ----------------------

SIST EN 286-4:1998

---------------------- Page: 27 ----------------------

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 13445-8:2021(Main)
Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
EN 13445-8:2021

This document specifies requirements for unfired pressure vessels and their parts made of aluminium and aluminium alloys in addition to the general requirements for unfired pressure vessels under EN 13445:2019 Parts 1 to 5. This document specifies unfired pressure vessels for loads up to 500 full cycles.
NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to or a revision of this document.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
kSIST FprEN 286-4:2022(Main)
Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium alloy pressure vessels designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock
FprEN 286-4

1.1   This document is applicable to simple unfired aluminium alloy pressure vessels, referred to as “vessel” in this document, designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock (see 1.6).
1.2   The vessels to this document are:
a)   made from a single shell;
b)   made from aluminium alloy;
c)   fabricated by welding;
d)   used at a maximum working pressure of 10 bar;
e)   the product of the maximum working pressure (in bar) and the volume (in litre): 50 bar litres < PV ≤ 10 000 bar litres;
f)   made of a cylindrical part of circular cross section called the shell with two outwardly dished torispherical ends, that is two dished ends with the same axis of rotation. This document therefore does not apply to vessels with one or two flat ends or those made up of several compartments;
g)   calculated with a design pressure P (See 5.1.4.2);
h)   designed for a working temperature of between −50 °C and +100 °C [+65 °C for certain grades of aluminium alloy (see 4.1.1)];
i)   fastened to the vehicles by straps.
1.3   In normal service, a momentary overpressure of 1 bar of the maximum working pressure is permitted (10 % of PS).
1.4   This document applies to the vessel proper, from the inlet connection to the outlet connection and to all other connections and fittings belonging to the vessel.
1.5   This document gives the requirements to be met for the calculation, design, fabrication, inspection during fabrication and certification of the vessel, and fittings for assembly to the vehicle.
These requirements cannot be written in sufficient detail to ensure good workmanship or proper construction. Each manufacturer is therefore responsible for taking every necessary step to make sure that the quality of workmanship and construction is such as to ensure compliance with good engineering practice.
This document gives:
a)   in Annex B, recommendations for assembly to the vehicles;
b)   in Annex C, recommendations for the service surveillance of vessels.
1.6   The requirements of this document apply to vessels designed to be fitted to rail vehicles used on the main national networks, urban networks, underground railways, trams, private networks (regional railways, company railways, etc.).

  • Draft
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13445-8:2014/oprA2:2018(Amendment)
Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
EN 13445-8:2021/prA1

Revise clause 15

  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13445-8:2021(Main)
Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
EN 13445-8:2021

This document specifies requirements for unfired pressure vessels and their parts made of aluminium and aluminium alloys in addition to the general requirements for unfired pressure vessels under EN 13445:2019 Parts 1 to 5. This document specifies unfired pressure vessels for loads up to 500 full cycles.
NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to or a revision of this document.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
kSIST FprEN 286-4:2022(Main)
Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium alloy pressure vessels designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock
FprEN 286-4

1.1   This document is applicable to simple unfired aluminium alloy pressure vessels, referred to as “vessel” in this document, designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock (see 1.6).
1.2   The vessels to this document are:
a)   made from a single shell;
b)   made from aluminium alloy;
c)   fabricated by welding;
d)   used at a maximum working pressure of 10 bar;
e)   the product of the maximum working pressure (in bar) and the volume (in litre): 50 bar litres < PV ≤ 10 000 bar litres;
f)   made of a cylindrical part of circular cross section called the shell with two outwardly dished torispherical ends, that is two dished ends with the same axis of rotation. This document therefore does not apply to vessels with one or two flat ends or those made up of several compartments;
g)   calculated with a design pressure P (See 5.1.4.2);
h)   designed for a working temperature of between −50 °C and +100 °C [+65 °C for certain grades of aluminium alloy (see 4.1.1)];
i)   fastened to the vehicles by straps.
1.3   In normal service, a momentary overpressure of 1 bar of the maximum working pressure is permitted (10 % of PS).
1.4   This document applies to the vessel proper, from the inlet connection to the outlet connection and to all other connections and fittings belonging to the vessel.
1.5   This document gives the requirements to be met for the calculation, design, fabrication, inspection during fabrication and certification of the vessel, and fittings for assembly to the vehicle.
These requirements cannot be written in sufficient detail to ensure good workmanship or proper construction. Each manufacturer is therefore responsible for taking every necessary step to make sure that the quality of workmanship and construction is such as to ensure compliance with good engineering practice.
This document gives:
a)   in Annex B, recommendations for assembly to the vehicles;
b)   in Annex C, recommendations for the service surveillance of vessels.
1.6   The requirements of this document apply to vessels designed to be fitted to rail vehicles used on the main national networks, urban networks, underground railways, trams, private networks (regional railways, company railways, etc.).

  • Draft
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13445-8:2014/oprA2:2018(Amendment)
Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
EN 13445-8:2021/prA1

Revise clause 15

  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 12349:2023(Main)
Mechanical vibration - Guide to the health effects of vibration on the human body
CEN/TR 12349:2023

The aim of this CEN report is to provide information on the possible adverse health effects caused by exposure to vibration at work.  the report addresses manufacturers as well as employers and employees using vibrating machinery in order to improve their understanding of the possible health problems arising from occupational exposure to vibration.

  • Technical report
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 80004-1:2023(Main)
Nanotechnologies - Vocabulary - Part 1: Core vocabulary (ISO 80004-1:2023)
EN ISO 80004-1:2023

This document defines core terms in the field of nanotechnology. This document is intended to facilitate communication between organizations and individuals in industry and those who interact with them.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3262-22:2023(Main)
Extenders - Specifications and methods of test - Part 22: Flux-calcined kieselguhr (ISO 3262-22:2023)
EN ISO 3262-22:2023

This document specifies requirements and corresponding methods of test for flux-calcined kieselguhr.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 18473-4:2023(Main)
Functional pigments and extenders for special applications - Part 4: Nanoscale titanium dioxide for photocatalytic application (ISO 18473-4:2022)
EN ISO 18473-4:2023

This document specifies requirements and corresponding test methods for nanoscale titanium dioxide (TiO2) in either powder or suspension form for photocatalytic application.
This document is applicable to modified nanoscale titanium dioxide for photocatalytic application. Such modification can be surface treatment, coating, doping and combination thereof.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day