Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 1: Classification, general and safety requirements

This document applies to centrifugal pumps without priming devices for fire-fighting use designed as
-   floating pumps (FPN F),
-   submersible pumps (FPN S) or
-   boosted pumps (FPN B).
Fire-fighting centrifugal pumps without primer are defined as terminated by their inlet and outlet connections as well as by their shaft ends.
This document applies for fire-fighting centrifugal pumps without priming devices for use under ambient temperatures between -15 °C and 40 °C.
NOTE 1   For special conditions, -30 C; see 6.11.
This document does not apply to fire-fighting centrifugal pumps without primer of which the only power source is directly applied manual effort.
This document does not apply to fire-fighting centrifugal pumps without primer, intended to be used as interchangeable equipment (i.e. combined by the user with another machine or vehicle acting as a driver).
This document does not apply to fire-fighting centrifugal pumps without primer with a nominal delivery pressure pN above 15 bar.
NOTE 2   High pressure pumps with primer are dealt with in EN 1028-1 and EN 1028-2.
This document specifies the classification and general requirements for fire-fighting centrifugal pumps without priming devices with a nominal delivery rate of up to 10 000 l/min.
This document deals with significant hazards listed in Clause 4, hazardous situations and events during the commissioning, operation and maintenance of fire-fighting centrifugal pumps without priming devices, used as intended and under the conditions foreseen by the manufacturer.
This document does not deal with the detailed verification of general and safety requirements and/or protective measures. These are covered in EN 14710-2 "Verification of general and safety requirements".
This document does not deal with noise.
This document does not deal with the technical safety requirements for the design or manufacture of drivers or of additional equipment intended to be fitted to inlet and outlet connections.

Feuerlöschpumpen - Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung - Teil 1: Klassifizierung, allgemeine Anforderungen und Sicherheitsanforderungen

Dieses Dokument gilt für Kreiselpumpen ohne Entlüftungseinrichtungen für Feuerlöschzwecke, die als
- Schwimmpumpen (FPN-F),
- Tauchpumpen (FPN-S) oder
- gespeiste Pumpen (FPN-B)
ausgeführt sind.
Die Grenzen von Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung sind durch ihre Eintritts- und
Austrittsanschlüsse sowie durch ihre Wellenenden festgelegt.
Dieses Dokument gilt für Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung, die in einem Umgebungstemperaturbereich
zwischen − 15 °C und 40 °C eingesetzt werden.
ANMERKUNG 1 Bei besonderen Bedingungen, − 30 °C, siehe 6.11.
Dieses Dokument gilt nicht für Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung, deren einzige
Kraftquelle die direkt aufgebrachte menschliche Arbeitskraft ist.
Dieses Dokument gilt nicht für Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung, die als auswechselbare
Ausrüstungen vorgesehen sind (z. B. durch den Anwender als Antrieb mit einer anderen Maschine oder
einem anderen Fahrzeug kombiniert).
Dieses Dokument gilt nicht für Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung mit einem Nennförderdruck,
pN, von mehr als 15 bar.
ANMERKUNG 2 Hochdruckpumpen mit Entlüftungseinrichtung sind Gegenstand von EN 1028-1 und 1028-2.
# Dieses Dokument legt die Klassifizierung und die allgemeinen Anforderungen für Feuerlöschkreiselpumpen
ohne Entlüftungseinrichtung mit einem Nennförderstrom bis 10 000 l/min fest. $
Dieses Dokument behandelt sämtliche in Abschnitt 4 aufgeführten signifikanten Gefährdungen, Gefährdungssituationen
und -ereignisse bei Inbetriebnahme, Betrieb und Instandhaltung von Feuerlösch-kreiselpumpen
ohne Entlüftungseinrichtung, wenn sie bestimmungsgemäß und unter den vom Hersteller vorhersehbaren
Bedingungen eingesetzt werden.
Dieses Dokument behandelt nicht die detaillierte Feststellung der Übereinstimmung mit den allgemeinen und
Sicherheitsanforderungen und/oder Schutzmaßnahmen.

Pompes à usage incendie - Pompes centrifuges à usage incendie sans dispositif d'amorçage - Partie 1: Classification, prescriptions générales et de sécurité

Le présent document s’applique aux pompes centrifuges à usage incendie sans dispositif d’amorçage,
utilisées comme :
— pompes flottantes (FPN-F) ;
— pompes immergées (FPN-S) ; ou
— pompes suralimentées (FPN-B).
Les pompes centrifuges à usage incendie sans dispositif d’amorçage sont définies comme étant terminées par leurs
orifices d’entrée et de sortie ainsi que par leurs extrémités d’axe.
Le présent document s’applique aux pompes centrifuges à usage incendie sans dispositif d’amorçage pour une
utilisation à une température ambiante pouvant varier entre – 15 °C et + 40 °C.
NOTE 1 Pour les conditions spéciales à – 30 °C, voir 6.11.
Le présent document ne s’applique pas aux pompes centrifuges à usage incendie sans dispositif d’amorçage pour
lesquelles la seule source d’énergie est la force humaine employée directement.
Le présent document ne s’applique pas aux pompes centrifuges à usage incendie sans dispositif d’amorçage
destinées à être utilisées comme équipement interchangeable (c'est-à-dire, combiné par l'utilisateur avec une autre
machine ou un véhicule agissant comme actionneur).
Le présent document ne s’applique pas aux pompes centrifuges à usage incendie sans dispositif d’amorçage ayant
une pression nominale de refoulement pN supérieure à 15 bar.
NOTE 2 Les pompes haute pression avec dispositif d'amorçage font l’objet des normes EN 1028-1 et EN 1028-2.
#Le présent document spécifie la classification et les prescriptions générales relatives aux pompes centrifuges
à usage incendie sans dispositif d'amorçage d'un débit nominal de refoulement pouvant aller jusqu'à 10 000 l/min.$
Le présent document traite des phénomènes dangereux significatifs listés à l’Article 4, des situations et des
événements dangereux pendant la mise en service, le fonctionnement et l’entretien des pompes centrifuges à usage
d’incendie sans dispositif d’amorçage, quand elles sont utilisées comme prévu et, dans les conditions prévues par
le fabricant.

Gasilske črpalke - Gasilske centrifugalne črpalke brez sesalne naprave - 1. del: Klasifikacija, splošne in varnostne zahteve

General Information

Status
Published
Publication Date
16-Dec-2008
Withdrawal Date
27-Dec-2009
Current Stage
9060 - Closure of 2 Year Review Enquiry - Review Enquiry
Start Date
04-Jun-2021
Completion Date
04-Jun-2021

Relations

Buy Standard

Standard
EN 14710-1:2005+A2:2009
English language
31 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Feuerlöschpumpen - Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung - Teil 1: Klassifizierung, allgemeine Anforderungen und SicherheitsanforderungenPompes à usage incendie - Pompes centrifuges à usage incendie sans dispositif d'amorçage - Partie 1: Classification, prescriptions générales et de sécuritéFire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 1: Classification, general and safety requirements13.220.10Gašenje požaraFire-fightingICS:Ta slovenski standard je istoveten z:EN 14710-1:2005+A2:2008SIST EN 14710-1:2005+A2:2009en,fr,de01-maj-2009SIST EN 14710-1:2005+A2:2009SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14710-1:2005+A2
December 2008 ICS 13.220.10; 23.080 Supersedes EN 14710-1:2005+A1:2008 English Version
Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 1: Classification, general and safety requirements Pompes à usage incendie - Pompes centrifuges à usage incendie sans dispositif d'amorçage - Partie 1: Classification, prescriptions générales et de sécurité
Feuerlöschpumpen - Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung - Teil 1: Klassifizierung, allgemeine Anforderungen und Sicherheitsanforderungen This European Standard was approved by CEN on 17 December 2004 and includes Amendment 1 approved by CEN on 6 June 2008 and Amendment 2 approved by CEN on 16 November 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14710-1:2005+A2:2008: ESIST EN 14710-1:2005+A2:2009

Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC . 29Annex ZB (informative)
!!!!Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""" . 30Bibliography . 31
Figures Figure 1 — Characteristic curve for the pressure in the outlet section pa (principle) . 11 Figure 2 — General warning sign ISO 7010-W001 . 23
Tables Table 1 — List of significant hazards . 14 Table 2 — Fire-fighting centrifugal pumps with nominal delivery pressures of 6 bar . 21 Table 3 — Fire-fighting centrifugal pumps with nominal delivery pressures of 10 bar . 21 Table 4 — Fire-fighting centrifugal pumps with nominal delivery pressures of 15 bar . 22
!" and # $. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document." This document is intended to be used in conjunction with part 2 of EN 14710 “Verification of general and safety requirements”. EN 14710 "Fire-fighting pumps – Fire-fighting centrifugal pumps without primer" comprises two parts:  Part 1: Classification, general and safety requirements;  Part 2: Verification of general and safety requirements. For relationship with EN 1028 see EN 14710-2:2005, 4.1. This document includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 14710-1:2005+A2:2009

 floating pumps (FPN-F),  submersible pumps (FPN-S) or
 boosted pumps (FPN-B).
Fire-fighting centrifugal pumps without primer are defined as terminated by their inlet and outlet connections as well as by their shaft ends. This document applies for fire-fighting centrifugal pumps without priming devices for use under ambient temperatures between -15 °C and 40 °C. NOTE 1 For special conditions, -30 °C; see 6.11. This document does not apply to fire-fighting centrifugal pumps without primer of which the only power source is directly applied manual effort. This document does not apply to fire-fighting centrifugal pumps without primer, intended to be used as interchangeable equipment (i.e. combined by the user with another machine or vehicle acting as a driver). This document does not apply to fire-fighting centrifugal pumps without primer with a nominal delivery pressure pN above 15 bar. NOTE 2 High pressure pumps with primer are dealt with in EN 1028-1 and EN 1028-2. #This document specifies the classification and general requirements for fire-fighting centrifugal pumps without priming devices with a nominal delivery rate of up to 10 000 l/min.$ This document deals with significant hazards listed in Clause 4, hazardous situations and events during the commissioning, operation and maintenance of fire-fighting centrifugal pumps without priming devices, used as intended and under the conditions foreseen by the manufacturer. This document does not deal with the detailed verification of general and safety requirements and/or protective measures. These are covered in EN 14710-2 "Verification of general and safety requirements". This document does not deal with noise. This document does not deal with the technical safety requirements for the design or manufacture of drivers or of additional equipment intended to be fitted to inlet and outlet connections. It does not cover risks directly arising from means provided for the portability, transportability, and mobility of pump units during or between periods of operation, or requirements for power transmission devices. In addition, this document does not cover:  hazards occurring due to decommissioning;  hazards during use due to a specific environment (e.g. traffic during use on public roads, potentially explosive atmospheres). This document does not apply to fire-fighting centrifugal pumps without primer that are manufactured before the date of publication by CEN of this document. SIST EN 14710-1:2005+A2:2009

(ISO 14121-1:2007) $. ISO 7010, Graphical symbols — Safety colours and safety signs — Safety signs used in workplaces and public areas 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003 and the following apply. 3.1 Pumps and their applications 3.1.1 fire-fighting
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.