prEN 18088
(Main)Flexible sheets for waterproofing - Plastics recycling and recycled plastics - Plastic waterproofing sheets
Flexible sheets for waterproofing - Plastics recycling and recycled plastics - Plastic waterproofing sheets
Plastic waterproofing sheets generate plastic waste at different stages: production, construction process, use and end of life.
This document defines the origin of recyclate made from pre-consumer material and post-consumer material as it is used in new products. These new products can be plastic waterproofing sheets, other sheets, other construction products or other products.
It specifies terms and definitions.
It gives guidance for assessing the recyclates intended for use in the production of new products.
NOTE This document is suitable for products with similar content like: swimming pool membranes, geosynthetic barriers, garden ponds, walk-ways, protection membranes, prefabricated pieces. The design for recycling of packaging, including the recycling itself, is defined in the CEN TC 261 Packaging.
Abdichtungsbahnen - Kunststoffrecycling und recycelte Kunststoffe - Kunststoffbahnen für Abdichtungen
Kunststoffbahnen für Abdichtungen erzeugen in verschiedenen Stadien Kunststoffabfall: Produktion, Bauprozess, Verwendung und Ende der Lebensdauer.
Dieses Dokument legt den Ursprung des aus Pre-Consumer- und Post-Consumer-Material produzierten Rezyklats fest, welches in neuen Produkten verwendet wird. Diese neuen Produkte können Kunststoffbahnen für Abdichtungen, andere Bahnen, andere Bauprodukte oder andere Produkte sein.
Es legt Begriffe fest.
Es dient als Leitfaden für die Bewertung des Rezyklats, das für die Verwendung in der Produktion neuer Produkte vorgesehen ist.
ANMERKUNG Dieses Dokument ist für Produkte mit ähnlichem Gehalt geeignet: z. B. Bahnen bei Schwimmbecken, geosynthetische Dichtungsbahnen, Gartenteiche, Laufstege, Schutzbahnen, vorgefertigte Teile. Die recyclinggerechte Gestaltung der Verpackung, einschließlich dem Recycling selbst, ist in CEN TC 261 Verpackung festgelegt.
Feuilles souples d’étanchéité - Recyclage des plastiques et plastiques recyclés - Feuilles d’étanchéité en plastique
Les feuilles d’étanchéité en plastique génèrent des déchets plastiques à différentes phases : production, processus de construction, utilisation et fin de vie.
Le présent document définit l’origine des recyclats fabriqués à partir de matières pré-consommation et post-consommation, tels qu’utilisés dans de nouveaux produits. Ces nouveaux produits peuvent être des feuilles d’étanchéité en plastique, d’autres types de feuilles, d’autres produits de construction ou d’autres produits.
Ce document spécifie des termes et leurs définitions.
Il fournit des recommandations pour l’évaluation des recyclats destinés à être utilisés dans la production de nouveaux produits.
NOTE Le présent document est adapté aux produits ayant un contenu similaire, comme les membranes de piscine, les barrières géosynthétiques, les bassins de jardin, les allées, les membranes de protection et les pièces préfabriquées. La conception en vue du recyclage des emballages, y compris le recyclage lui-même, est définie dans le CEN/TC 261 Emballage.
Hidroizolacijski trakovi - Recikliranje plastike in reciklirana plastika - Plastični hidroizolacijski trakovi
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2024
Hidroizolacijski trakovi - Recikliranje plastike in reciklirana plastika - Plastični
hidroizolacijski trakovi
Flexible sheets for waterproofing - Plastics recycling and recycled plastics - Plastic
waterproofing sheets
Abdichtungsbahnen - Kunststoffrecycling und recycelte Kunststoffe - Kunststoffbahnen
für Abdichtungen
Feuilles souples d’étanchéité - Recyclage des plastiques et plastiques recyclés - Feuilles
d’étanchéité en plastique
Ta slovenski standard je istoveten z: prEN 18088
ICS:
13.030.50 Recikliranje Recycling
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2024
ICS 13.030.50; 91.100.50
English Version
Flexible sheets for waterproofing - Plastics recycling and
recycled plastics - Plastic waterproofing sheets
Feuilles souples d'étanchéité - Recyclage des plastiques Abdichtungsbahnen - Kunststoffrecycling und recycelte
et plastiques recyclés - Feuilles plastiques pour Kunststoffe - Kunststoffbahnen für Abdichtungen
l'étanchéité
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 254.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 18088:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Typical application systems . 8
5 Collection . 9
6 Characterization . 9
6.1 General. 9
6.2 Visual properties . 9
6.3 Physical properties . 9
6.4 Mechanical properties . 9
6.5 Thermal properties . 10
6.6 Content . 10
7 Quality assurance . 10
8 Recycled content . 10
9 Design for recycling . 10
Annex A (informative) Examples to illustrate some definitions and guidance for calculating
recycled content in green building systems . 12
A.1 Example 1: Manufacturing of a mono-layer product . 12
A.1.1 General. 12
A.1.2 Reworking within the same product . 12
A.1.3 Recycling within another product . 14
A.2 Example 2: Manufacturing of a multi-layer product . 14
A.3 Example 3: Building site material, construction process stage . 15
A.4 Example 4: Building site material, end-of-life stage. 15
Annex B (informative) Flowchart for plastic recovery options . 17
Bibliography . 19
European foreword
This document (prEN 18088:2024) has been prepared by Technical Committee CEN/TC 254 “Flexible
sheets for waterproofing”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
Introduction
This document is in accordance with the European Commission implementing decision M/584 on a
standardization request to the European Committee for Standardization and the European Committee
for Electrotechnical Standardization as regards plastics recycling and recycled plastics in support of the
European Strategy for Plastics in a Circular Economy.
A plastic waterproofing sheet is an article as identified in article 3 of Regulation (EU) N° 1907/2006
(REACH). It contains no substances which are intended to be released from the article under normal or
reasonably foreseeable conditions of use. Based on current knowledge, plastic waterproofing sheets do
not contain SVHC (Substances of very high concern) as listed in Annex XIV of the REACH regulation or on
the candidate list published by the European Chemicals Agency in concentrations above 0,1 % (w/w).
Under the umbrella from the European Union’s Waste Framework Directive 2008/98/EC recycling of
waste is one type of material recovery process intended to save resources (virgin raw materials, water,
and energy), while minimizing harmful emissions into air, water, and soil as well as any impacts on
human health. The environmental impact of recycling should be assessed over the whole life cycle of the
recycling process.
It might be impossible to trace back each individual product including components of the product at the
end user stage and to check whether the product has been used correctly through its life. It is possible
that during this period contamination with other materials might occur that could affect the product’s
suitability for recycling into the intended application.
1 Scope
Plastic waterproofing sheets generate plastic waste at different stages: production, construction process,
use and end of life.
This document defines the origin of recyclate made from pre-consumer material and post-consumer
material as it is used in new products. These new products can be plastic waterproofing sheets, other
sheets, other construction products or other products.
It specifies terms and definitions.
It gives guidance for assessing the recyclates intended for use in the production of new products.
NOTE This document is suitable for products with similar content like: swimming pool membranes,
geosynthetic barriers, garden ponds, walk-ways, protection membranes, prefabricated pieces. The design for
recycling of packaging, including the recycling itself, is defined in the CEN TC 261 Packaging.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 13956, Flexible sheets for waterproofing — Plastic and rubber sheets for roof waterproofing —
Definitions and characteristics
EN 13967, Flexible sheets for waterproofing — Plastic and rubber damp proof sheets including plastic and
rubber basement tanking sheet — Definitions and characteristics
EN 14909, Flexible sheets for waterproofing — Plastic and rubber damp proof courses — Definitions and
characteristics
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
batch
quantity of material regarded as a single unit, and having a unique reference
3.2
certificate of analysis
CoA
document produced by manufacturers certifying that the product they manufactured conforms to their
customer’s requirements
Note 1 to entry: A formal certificate of analysis can be replaced by an internal procedure documented in the factory
production control (FPC) system for recycling of plastic materials within the same manufacturer location.
3.3
component
constituent of a product that fulfils a specific function
3.4
design for recycling
part of component for which a recovery and recycling scheme exist
3.5
energy recovery
production of useful energy through direct and controlled combustion
3.6
feedstock / chemical recycling
conversion to monomer or production of new raw materials by changing the chemical structure of plastic
waste through cracking, gasification or depolymerisation, excluding energy recovery
3.7
flake
plate-like shaped regrind
3.8
granule
small particle produced in many sizes and shapes
3.9
ingredient
part of a compound or component
3.10
mechanical recycling
processing of plastic waste into secondary raw material or products without significantly changing the
chemical structure of the material
3.11
micronizing
process by which plastic materials are ground into a fine powder
3.12
pellet
small, rounded, or tube-shaped, compressed mass of a substance, ingredient, or compound
3.13
plastic
material consisting of a polymer, to which additives or other substances may have been added, and which
can function as a main structural component of final products, with the exception of natural polymers
that have not been chemically modified
Note 1 to entry: A definition of polymer can be found in point 5 of Article 3 of Regulation (EC) 1907/2006.
3.14
post-consumer material
descriptive term covering plastics materials generated by the end-users of products that have been
placed on the market, which has fulfilled its intended purpose or can no longer be used
3.15
pre-consumer material
descriptive term covering plastic materials diverted during a manufacturing process
Note 1 to entry: This term excludes re-utilized plastic materials, such as rework, regrind or scrap that has been
generated in a process and is capable of being reclaimed within the same process.
Note 2 to entry: The same process refers to a repetition of a manufacturing operation or the production of the same
type of product that has been already conducted.
3.16
substance
part of an ingredient or compound
3.17
product
physical-based object designed with a specific build-up and specific formulation(s) or utilized with a
specific purpose(s)
3.18
recyclate
plastic materials resulting from the recycling of plastic waste, that is no longer waste and can be used for
the manufacturing of new articles or products and can be reformulated using additives
Note 1 to entry: As soon as the used plastic
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.