iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61496-1:2004

(Main)

Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests

Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests

defines a real-time optical serial interface between the control unit and its associate drives which is utilized to transmit periodic and non-periodic data. This interface is intended to apply to industrial machines, such as machine tools, with multiple drives and which can be operated in torque, velocity, or position interface operation modes.

Sicherheit von Maschinen - Berührungslos wirkende Schutzeinrichtungen - Teil 1: Allgemeine Anforderungen und Prüfungen

Sécurité des machines - Equipements de protection électro-sensibles - Partie 1: Prescriptions générales et essais

définit une interface sérielle optique en temps réel entre la commande numérique et ses dispositifs d'entraînement associés, utilisée pour la transmission de données périodiques ou non. Cette interface est destinée à être appliquée aux machines industrielles, telles que les machines outils, avec des dispositifs d'entraînement multiples et pouvant fonctionner en mode couple, vitesse ou en modes de fonctionnement interfaces de position.

Varnost strojev – Električno občutljiva varovalna oprema – 1. del: Splošne zahteve in preskusi (IEC 61496-1:2004, spremenjen)

General Information

Status
Withdrawn
Publication Date
13-May-2004
ICS
29.260.99 - Other electrical equipment for working in special conditions
Technical Committee
CLC/TC 44X - Safety of machinery: electrotchnical aspects
Drafting Committee
IEC/TC 44 - IEC_TC_44
Parallel Committee
IEC/TC 44 - IEC_TC_44
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
10-May-2015
Completion Date
10-May-2015
Directive
2004/108/EC - Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
89/336/EEC - Electromagnetic compatibility (EMC)
98/37/EC - Machinery
Mandate
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
SIST EN 61496-1:2005 - Safety of machinery - Electro-sensitive protective equipment -- Part 1: General requirements and tests

Relations

Replaces
EN 61496-1:1997 - Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
Effective Date
29-Jan-2023
Replaced By
EN 61496-1:2013 - Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
Effective Date
29-Jan-2023
Amended By
EN 61496-1:2004/A1:2008 - Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
Effective Date
29-Jan-2023

Buy Standard

EN 61496-1:2005EN 61496-1:2005
PreviousNext
Standard
EN 61496-1:2005
English language
57 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sicherheit von Maschinen - Berührungslos wirkende Schutzeinrichtungen -- Teil 1: Allgemeine Anforderungen und PrüfungenSécurité des machines - Equipements de protection électro-sensibles -- Partie 1: Prescriptions générales et essaisSafety of machinery - Electro-sensitive protective equipment -- Part 1: General requirements and tests31.260Optoelektronika, laserska opremaOptoelectronics. Laser equipment13.110Varnost strojevSafety of machineryICS:Ta slovenski standard je istoveten z:EN 61496-1:2004SIST EN 61496-1:2005en01-marec-2005SIST EN 61496-1:2005SLOVENSKI
STANDARD



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIST EN 61496-1:2005



SIS
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 61496-2:2020(Main)
Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
SIST EN IEC 61496-2:2020

IEC 61496-2:2020 specifies requirements for the design, construction and testing of electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part of a safety-related system, employing active opto-electronic protective devices (AOPDs) for the sensing function. Special attention is directed to features which ensure that an appropriate safety-related performance is achieved. An ESPE can include optional safety-related functions, the requirements for which are given in Annex A of IEC 61496-1:2020 and of this document. This document does not specify the dimensions or configurations of the detection zone and its disposition in relation to hazardous parts for any particular application, nor what constitutes a hazardous state of any machine. It is restricted to the functioning of the ESPE and how it interfaces with the machine. Excluded from this document are AOPDs employing radiation at wavelengths outside the range 400 nm to 1 500 nm. This document can be relevant to applications other than those for the protection of persons, for example, the protection of machinery or products from mechanical damage. In those applications, additional requirements can be necessary, for example, when the materials that are to be recognized by the sensing function have different properties from those of persons. This document does not deal with electromagnetic compatibility (EMC) emission requirements. IEC 61496-2:2020 cancels and replaces the third edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Requirements and test procedures in Part 2 that were found to be common to all ESPEs have been moved to Part 1. Test procedures that are dependent on the sensing technology remain in Part 2.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61496-1:2020(Main)
Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
SIST EN IEC 61496-1:2020

IEC 61486-1:2020 specifies general requirements for the design, construction and testing of non-contact electro-sensitive protective equipment (ESPE) designed specifically to detect persons or part of a person as part of a safety-related system. Special attention is directed to functional and design requirements that ensure an appropriate safety-related performance is achieved. An ESPE can include optional safety-related functions, the requirements for which are given in Annex A. This document is intended to be used with a subsequent part of IEC 61496 that provides particular requirements based on the sensing technology. Where a part covering the sensing technology does not exist, IEC TS 62998-1 is used. Where the IEC 61496 series does not contain all necessary provisions, IEC TS 62998-1 is used. It is an additional possibility to combine those aspects covered by the IEC 61496 series in addition to IEC TS 62998-1. This document does not specify the dimensions or configuration of the detection zone and its disposition in relation to hazards in any particular application, nor what constitutes a hazardous state of any machine. It is restricted to the functioning of the ESPE and how it interfaces with the machine. While a data interface can be used to control optional safety-related ESPE functions (Annex A), this document does not provide specific requirements. Requirements for these safety-related functions can be determined by consulting other standards (for example, IEC 61508 (all parts), IEC TS 62046, IEC 62061, and ISO 13849-1). This document can be relevant to applications other than those for the protection of persons, for example for the protection of machinery or products from mechanical damage. In those applications, different requirements can be appropriate, for example when the materials that have to be recognized by the sensing function have different properties from those of persons. This document does not deal with requirements for ESPE functions not related to the protection of persons (e.g. using sensing unit data for navigation). This document does not deal with electromagnetic compatibility (EMC) emission requirements. IEC 61486-1:2020 cancels and replaces the third edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) It has been clarified that some requirements for ESPEs that are dependent on sensing technology are not included in IEC 61496-1. They are provided in a subsequent part of IEC 61496. b) Requirements for protection against environmental influences from subsequent parts of IEC 61496 that are common to all ESPEs have been consolidated into IEC 61496-1. c) Some test procedures in IEC 61496-1 were incomplete. They have been expanded with more detail and step by step procedures. d) Some requirements and procedures in IEC 61496-1 are now covered by new generic machine safety standards. The requirements in IEC 61496-1 have been harmonized with references to the new generic standards.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62819:2023(Main)
Live working - Eye, face and head protectors against the effects of electric arc - Performance requirements and test methods
SIST EN IEC 62819:2023

This part of IEC 63275-1 gives a test method to evaluate gate threshold voltage shift of silicon carbide (SiC) power metal-oxide-semiconductor field-effect transistors (MOSFETs) using room temperature readout after applying continuous positive gate-source voltage stress at elevated temperature. The proposed method accepts a certain amount of recovery by allowing large delay times between stress and measurement (up to 10h).

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61318:2021(Main)
Live working - Methods for assessment of defects and verification of performance applicable to tools, devices and equipment
SIST EN IEC 61318:2021

This document defines methods to assess defects and to verify that products after the manufacturer process meet the requirements of the corresponding product standard. The principles of assessment of defects for live working products are detailed in this document to assist product standard developers in prescribing the best means to achieve suitable quality of every finished tool, device and piece of equipment. The following elements are not covered by the present document, but are included in each product standard: - type tests; - provisions and description for routine, sampling and acceptance tests; - identification and classification of defects; - risk analysis. This document does not cover conformity assessment of commercial shipments or certifications.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61243-1:2021(Main)
Live working - Voltage detectors - Part 1: Capacitive type to be used for voltages exceeding 1 kV AC
SIST EN IEC 61243-1:2021

IEC 61243-1:2021 is applicable to portable voltage detectors, with or without built-in power sources, to be used on electrical systems for voltages of 1 kV to 800 kV AC, and frequencies of 50 Hz and/or 60 Hz. This document applies only to voltage detectors of capacitive type used in contact with the bare part to be tested, as a complete device including its insulating element or as a separate device, adaptable to an insulating stick which, as a separate tool, is not covered by this document (see 4.4.2.1 for general design). Other types of voltage detectors are not covered by this document. Self ranging voltage detectors (formally "multi range voltage detectors") are not covered by this document. Some restrictions or formal interdictions on their use are applicable in case of switchgear of IEC 62271 series design, due to insulation coordination, on overhead line systems of electrified railways (see Annex B) and systems without neutral reference. For systems without neutral reference, the insulating level is adapted to the maximum possible voltage to the earth (ground). Products designed and manufactured according to this document contribute to the safety of users provided they are used by persons trained for the work, in accordance with the hot stick working method and the instructions for use. Except where otherwise specified, all the voltages defined in this document refer to values of phase-to-phase voltages of three-phase systems. In other systems, the applicable phase-to-phase or phase-to-earth (ground) voltages are used to determine the operating voltage. This third edition cancels and replaces the second edition published in 2003 and Amend-ment 1:2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The scope is more precise, stating that only bare contact to the part to be tested is reliable for these contact voltage detectors. The rationale is that tests on painted or coated conductors have led to wrong indications, as this non-conductive paint or coat acts as a capacitor with different capacity according to the thickness. This capacity has an effect on the threshold voltage. b) A contact probe is introduced as a new type of non-conductive contact electrode. c) A new type "exclusively outdoor type" has been defined and implemented into the requirements and test procedure. d) A selector for voltage and frequency is allowed if foreseeable misuse is excluded. e) The marking for voltage detectors with low interference voltage has been made more precise. f) The indication groups have been made more precise and requirements and tests for the "ready to operate state" and "stand-by state" added. g) Requirements and tests for electromagnetic compatability have been implemented. h) An example for good electrical connection for the tests is introduced.

  • Standard
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61472-2:2021(Main)
Live working - Minimum approach distances - Part 2: Method of determination of the electrical component distance for AC systems from 1,0 kV to 72,5 kV
SIST EN IEC 61472-2:2021

IEC 61472-2:2021 specifies a method for determining the electrical component of the minimum approach distances for live working, for AC systems 1 kV up to and including 72,5 kV. This document addresses system overvoltages and the working air distances between equipment and/or workers at different potentials. The withstand voltage and minimum approach distances determined by the method described in this document can be used only if the following working conditions prevail:  workers are trained for, and skilled in, working live lines or close to live conductors or equipment; the operating conditions are adjusted so that the statistical overvoltage does not exceed the value selected for the determination of the required withstand voltage; transient overvoltages are the determining overvoltages; tool insulation has no continuous film of moisture present on the surface; no lightning is observed within 10 km of the work site; allowance is made for the effect of the conducting components of tools.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61496-2:2020(Main)
Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
SIST EN IEC 61496-2:2020

IEC 61496-2:2020 specifies requirements for the design, construction and testing of electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part of a safety-related system, employing active opto-electronic protective devices (AOPDs) for the sensing function. Special attention is directed to features which ensure that an appropriate safety-related performance is achieved. An ESPE can include optional safety-related functions, the requirements for which are given in Annex A of IEC 61496-1:2020 and of this document. This document does not specify the dimensions or configurations of the detection zone and its disposition in relation to hazardous parts for any particular application, nor what constitutes a hazardous state of any machine. It is restricted to the functioning of the ESPE and how it interfaces with the machine. Excluded from this document are AOPDs employing radiation at wavelengths outside the range 400 nm to 1 500 nm. This document can be relevant to applications other than those for the protection of persons, for example, the protection of machinery or products from mechanical damage. In those applications, additional requirements can be necessary, for example, when the materials that are to be recognized by the sensing function have different properties from those of persons. This document does not deal with electromagnetic compatibility (EMC) emission requirements. IEC 61496-2:2020 cancels and replaces the third edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Requirements and test procedures in Part 2 that were found to be common to all ESPEs have been moved to Part 1. Test procedures that are dependent on the sensing technology remain in Part 2.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61496-1:2020(Main)
Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
SIST EN IEC 61496-1:2020

IEC 61486-1:2020 specifies general requirements for the design, construction and testing of non-contact electro-sensitive protective equipment (ESPE) designed specifically to detect persons or part of a person as part of a safety-related system. Special attention is directed to functional and design requirements that ensure an appropriate safety-related performance is achieved. An ESPE can include optional safety-related functions, the requirements for which are given in Annex A. This document is intended to be used with a subsequent part of IEC 61496 that provides particular requirements based on the sensing technology. Where a part covering the sensing technology does not exist, IEC TS 62998-1 is used. Where the IEC 61496 series does not contain all necessary provisions, IEC TS 62998-1 is used. It is an additional possibility to combine those aspects covered by the IEC 61496 series in addition to IEC TS 62998-1. This document does not specify the dimensions or configuration of the detection zone and its disposition in relation to hazards in any particular application, nor what constitutes a hazardous state of any machine. It is restricted to the functioning of the ESPE and how it interfaces with the machine. While a data interface can be used to control optional safety-related ESPE functions (Annex A), this document does not provide specific requirements. Requirements for these safety-related functions can be determined by consulting other standards (for example, IEC 61508 (all parts), IEC TS 62046, IEC 62061, and ISO 13849-1). This document can be relevant to applications other than those for the protection of persons, for example for the protection of machinery or products from mechanical damage. In those applications, different requirements can be appropriate, for example when the materials that have to be recognized by the sensing function have different properties from those of persons. This document does not deal with requirements for ESPE functions not related to the protection of persons (e.g. using sensing unit data for navigation). This document does not deal with electromagnetic compatibility (EMC) emission requirements. IEC 61486-1:2020 cancels and replaces the third edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) It has been clarified that some requirements for ESPEs that are dependent on sensing technology are not included in IEC 61496-1. They are provided in a subsequent part of IEC 61496. b) Requirements for protection against environmental influences from subsequent parts of IEC 61496 that are common to all ESPEs have been consolidated into IEC 61496-1. c) Some test procedures in IEC 61496-1 were incomplete. They have been expanded with more detail and step by step procedures. d) Some requirements and procedures in IEC 61496-1 are now covered by new generic machine safety standards. The requirements in IEC 61496-1 have been harmonized with references to the new generic standards.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60895:2020(Main)
Live working - Conductive clothing
SIST EN IEC 60895:2020

IEC 60895:2020 is applicable to conductive clothing, worn during live working (especially bare-hand working) on AC and DC electrical installations, to provide electrical continuity between all parts of the clothing and a reduction of electric field inside the clothing. This document is applicable to conductive clothing assembled from a conductive garment (jackets and trousers or coveralls forming a one-piece garment) and from conductive component parts (gloves, hoods or helmets, shoes or boots, overshoe socks and socks) in electrical systems with nominal voltage up to 1 000 kV AC and up to ±800 kV DC. This document does not indicate values of protection from the effects of the electric arc, because any value indicated would not guarantee the necessary protection from the effects of electric arcs, or the operator would need to wear very heavy and rigid conductive clothing, which would not allow the execution of the work in safety. The products designed and manufactured according to this document contribute to the safety of the users provided they are used by persons trained for the work, in accordance with the live working methods and the instructions for use. This third edition cancels and replaces the second edition, published in 2002. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) increase of the use up to 1 000 kV AC and ±800 kV DC; b) introduction of two classes of conductive clothing with different electrical requirements; c) revision of the electrical requirements of conductive clothing; d) definition of specific resistance values for each component part of the conductive clothing; e) introduction of conductive helmet and conductive scarf as component parts of conductive clothing; f) introduction of mechanical requirements and new tests for fabrics; g) update of the cleaning test procedures; h) revision of the efficiency test of the conductive clothing to improve the feasibility and repeatability; i) preparation of the elements of classification of defects, and general application of IEC 61318:2007; j) the normative Annex B for the classification of tests has been replaced by normative Annex C for the general type tests procedure, the normative Annex D for the classification of defects and the informative Annex E providing the justification for the classification of defects; k) the normative Annex C on sampling procedure has been deleted (not applicable according to IEC 61318:2007); l) modification of the recommended frequency of the periodic tests.

  • Standard
    72 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60900:2018/AC:2020-05(Corrigendum)
Live working - Hand tools for use up to 1 000 V AC and 1 500 V DC
SIST EN IEC 60900:2018/AC:2020

TAN - // IEC Corrigendum

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day