Bonded Glazing for doors, windows and curtain walling - Verification of mechanical performance of bonding on aluminium and steel surfaces

This document specifies the method to be used to verify the mechanical performance of the bonded glazing for doors, windows and curtain walling (see examples in Annex A) and its durability. The bonding covered is only that between the glass and the untreated, treated or coated metal surface.
NOTE 1   Bonded glazing was formerly known as structural sealant glazing SSGS.
This document covers bonded glazing incorporated into the product construction works as follows:
-   either vertically; or
-   up to 83° from the vertical (positive slope); or
-   up to 15° from the vertical onto the building face (negative slope).
NOTE 2   A wall has a positive slope if its outer surface faces upwards (see Figure A.1).
Specific additional safety provisions may apply nationally.
This document gives information to the manufacturer to comply with requirements regarding design, factory production control and assembly rules.
The parts concerned in the testing are the metal surface (anodized and coated aluminium, stainless steel), the surface of glass, provided or not, with a layer or coating, which shall be bonded, the bonding sealant and mechanical restraints when required.
This document does not apply to:
-   other surfaces materials;
-   direct glazing;
-   glass-to-glass bonding and edge seal of insulating glass units (which are covered by EN 13022-1 and EN 1279-5);
-   adhesive tapes.

Geklebte Glaskonstruktionen für Türen, Fenster und Vorhangfassaden - Überprüfung der mechanischen Leistungseigenschaften der Verklebung auf Aluminium- und Stahloberflächen

Dieses Dokument legt das anzuwendende Verfahren zum Nachweis der mechanischen Leistungseigenschaften der geklebten Glaskonstruktionen für Türen, Fenster und Vorhangfassaden (siehe Beispiele in Anhang A) und deren Dauerhaftigkeit fest. Es werden nur die Verklebungen zwischen dem Glas und der unbehandelten, vorbehandelten oder beschichteten Metalloberfläche erfasst.
ANMERKUNG 1 Geklebte Glaskonstruktionen wurden vorher als Structural-Sealant-Glazing-System (SSGS) bezeichnet.
Dieses Dokument behandelt geklebte Glaskonstruktionen, die wie folgt im Bauwerksprodukt eingebaut sind:
- entweder vertikal angeordnet; oder
- bis zu 83° von der Vertikalen (positive Neigung); oder
- bis zu 15° von der Vertikalen auf der Gebäudefassade (negative Neigung).
ANMERKUNG 2 Eine Wand weist eine positive Neigung auf, wenn ihre Außenfläche nach oben zeigt (siehe Bild A.1).
Auf nationaler Ebene gelten möglicherweise zusätzliche spezifische Sicherheitsbestimmungen.
Dieses Dokument liefert dem Hersteller Angaben zur Übereinstimmung mit Anforderungen bezüglich Aus¬führung, werkseigener Produktionskontrolle und Verglasungsvorschriften.
Die von der Prüfung betroffenen Teile sind die Metalloberflächen (anodisiertes und beschichtetes Aluminium, nichtrostender Stahl), mit oder ohne Beschichtung versehene Glasoberflächen, die geklebt sein müssen, der Klebedicht¬stoff und mechanische Halterungen, falls erforderlich.
Dieses Dokument ist nicht anzuwenden für:
- andere Oberflächenmaterialien;
- geklebte Verglasung/Direktverglasung;
- den Glas/Glas-Verbund und Randverbund von Mehrscheiben-Isolierglaseinheiten (welche durch EN 13022 1 und EN 1279 5 behandelt werden);
- Klebebänder.

Vitrages extérieurs collés (VEC) pour portes, fenêtres et façades rideaux - Vérification des propriétés mécaniques de collage sur surfaces aluminium et acier

Le présent document spécifie la méthode à utiliser pour vérifier les performances mécaniques des vitrages extérieurs collés pour portes, fenêtres et façades rideaux (voir exemples à l’Annexe A) ainsi que leur durabilité. La présente norme ne traite que du collage entre le verre et la surface métallique non traitée, traitée ou revêtue.
NOTE 1 Le vitrage collé était auparavant connu sous le nom de vitrage structurel d'étanchéité SSGS
Le présent document couvre les vitrages collés intégrés de l’une des manières suivantes dans les travaux de construction réalisés :
 Soit verticalement ; ou
 inclinés jusqu’à 83° par rapport à la verticale (pente positive) ; ou
 inclinés jusqu’à 15° par rapport à la verticale sur la façade du bâtiment (pente négative).
NOTE 2 Une façade a une pente positive si sa surface extérieure est orientée vers le haut (voir Figure A.1).
Des dispositions de sécurité supplémentaires spécifiques peuvent s'appliquer au niveau national.
Le présent document fournit des informations au fabricant lui permettant de satisfaire aux exigences relatives à la conception, au contrôle de la production en usine et aux règles d’assemblage.
Les parties concernées par les essais sont les surfaces métalliques (aluminium anodisé et thermolaqué, acier inoxydable), la surface du verre, pourvue ou non d'une couche ou d'un revêtement, qui doit être collé, le mastic de collage et les dispositifs de retenue mécanique, le cas échéant.
Le présent document ne s’applique pas :
- aux autres matériaux de surface ;
- au vitrage direct « direct glazing » ;
- au collage verre sur verre ni aux assemblages par collage des vitrages isolants (qui sont couverts par l’EN 13022-1 et l’EN 1279-5) ;
- aux bandes adhesives.

Lepljena zasteklitev za vrata, okna in obešene fasade - Preverjanje mehanskih lastnosti zlepljenosti aluminijeve in jeklene površine

General Information

Status
Published
Publication Date
24-Aug-2021
Withdrawal Date
27-Feb-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
25-Aug-2021
Due Date
05-Nov-2021
Completion Date
25-Aug-2021

Buy Standard

Standard
EN 16759:2021
English language
32 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 16759:2019
English language
34 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 16759:2021
01-oktober-2021
Lepljena zasteklitev za vrata, okna in obešene fasade - Preverjanje mehanskih
lastnosti zlepljenosti aluminijeve in jeklene površine
Bonded Glazing for doors, windows and curtain walling - Verification of mechanical
performance of bonding on aluminium and steel surfaces
Geklebte Glaskonstruktionen für Türen, Fenster und Vorhangfassaden - Überprüfung der
mechanischen Leistungseigenschaften der Verklebung auf Aluminium- und
Stahloberflächen
Vitrages extérieurs collés (VEC) pour portes, fenêtres et façades rideaux - Vérification
des propriétés mécaniques de collage sur surfaces aluminium et acier
Ta slovenski standard je istoveten z: EN 16759:2021
ICS:
81.040.20 Steklo v gradbeništvu Glass in building
SIST EN 16759:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 16759:2021

---------------------- Page: 2 ----------------------
SIST EN 16759:2021


EN 16759
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2021
EUROPÄISCHE NORM
ICS 81.040.20
English Version

Bonded Glazing for doors, windows and curtain walling -
Verification of mechanical performance of bonding on
aluminium and steel surfaces
Vitrages extérieurs collés (VEC) pour portes, fenêtres Geklebte Glaskonstruktionen für Türen, Fenster und
et façades rideaux - Vérification des propriétés Vorhangfassaden - Überprüfung der mechanischen
mécaniques de collage sur surfaces aluminium et acier Leistungseigenschaften der Verklebung auf
Aluminium- und Stahloberflächen
This European Standard was approved by CEN on 11 July 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16759:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 16759:2021
EN 16759:2021 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Symbols and abbreviations . 7
5 Component requirements . 7
5.1 Glass for bonded glazing . 7
5.2 Bonding sealant . 7
5.3 Anodized aluminium adhesion surface . 8
5.3.1 Alloys of aluminium .
...

SLOVENSKI STANDARD
oSIST prEN 16759:2019
01-november-2019
Lepljena zasteklitev za vrata, okna in obešene fasade - Preverjanje mehanskih
lastnosti zlepljenosti aluminijeve in jeklene površine
Bonded Glazing for doors, windows and curtain walling - Verification of mechanical
performance of bonding on aluminium and steel surfaces
Geklebte Glaskonstruktionen für Türen, Fenster und Vorhangfassaden - Überprüfung der
mechanischen Leistungseigenschaften der Verklebung auf Aluminium- und
Stahloberflächen
Vitrages extérieurs collés (VEC) pour portes, fenêtres et façades rideaux - Vérification
des propriétés mécaniques de collage sur surfaces aluminium et acier
Ta slovenski standard je istoveten z: prEN 16759
ICS:
81.040.20 Steklo v gradbeništvu Glass in building
oSIST prEN 16759:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 16759:2019

---------------------- Page: 2 ----------------------
oSIST prEN 16759:2019


DRAFT
EUROPEAN STANDARD
prEN 16759
NORME EUROPÉENNE

EUROPÄISCHE NORM

September 2019
ICS 81.040.20
English Version

Bonded Glazing for doors, windows and curtain walling -
Verification of mechanical performance of bonding on
aluminium and steel surfaces
Vitrages extérieurs collés (VEC) pour portes, fenêtres Geklebte Glaskonstruktionen für Türen, Fenster und
et façades rideaux - Vérification des propriétés Vorhangfassaden - Überprüfung der mechanischen
mécaniques de collage sur surfaces aluminium et acier Leistungseigenschaften der Verklebung auf
Aluminium- und Stahloberflächen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 33.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16759:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 16759:2019
prEN 16759:2019 (E)
European foreword
This document (prEN 16759:2019) has been prepared by Technical Committee CEN/TC 33 “Doors,
windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
2

---------------------- Page: 4 ----------------------
oSIST prEN 16759:2019
prEN 16759:2019 (E)
Contents Page
European foreword .2
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .8
4 Symbols and abbreviations .8
5 Component requirements .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.