iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14214:2012+A1:2014

(Main)

Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods

Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods

This European Standard specifies requirements and test methods for marketed and delivered fatty acid methyl esters (hereafter known as FAME) to be used either as fuel for diesel engines and for heating applications at 100 % concentration, or as an extender for distillate fuel for diesel engines in accordance with the requirements of EN 590 and for heating fuel. At 100 % concentration it is applicable to fuel for use in diesel engines and in heating applications designed or subsequently adapted to run on 100 % FAME.
NOTE   For the purposes of this European Standard, the terms % (m/m) and % (V/V) are used to represent respectively the mass fraction, µ, and the volume fraction, φ.

Flüssige Mineralölerzeugnisse - Fettsäure-Methylester (FAME) zur Verwendung in Dieselmotoren und als Heizöl - Anforderungen und Prüfverfahren

Diese Europäische Norm legt Anforderungen und Prüfverfahren für gehandelte und ausgelieferte Fettsäure-Methylester (en: Fatty Acid Methyl Esters, FAME) für die Verwendung in Kraftfahrzeugen mit Dieselmotoren oder als Heizöl fest, entweder als Dieselkraftstoff bzw. Heizöl mit einer Konzentration von 100 %, oder als Blendkomponente für Dieselkraftstoff in Übereinstimmung mit den Anforderungen nach EN 590 bzw. für Heizöl. Bei einer Konzentration von 100 % ist FAME einsetzbar in Fahrzeugen mit Dieselmotoren und in Heizungsanlagen, welche für den Einsatz von 100 % FAME entwickelt oder nachträglich angepasst wurden.
ANMERKUNG In dieser Europäischen Norm werden die Symbole "% (m/m)" und "% (V/V)" verwendet, um Massenanteile (μ ) bzw. Volumenanteile (φ ) in % auszudrücken.

Produits pétroliers liquides - Esters méthyliques d'acides gras (EMAG) pour moteurs diesel et comme combustible de chauffage - Exigences et méthodes d'essai

La présente Norme européenne spécifie les exigences et méthodes d'essais applicables aux esters méthyliques
d'acides gras (dénommés EMAG par la suite), commercialisés et livrés comme carburant pour moteurs diesel et pour
des applications de chauffage, soit à une concentration de 100 %, soit comme composant de distillats combustibles
pour les moteurs diesel, conformément aux exigences de l'EN 590, et pour le fioul domestique. À la concentration
de 100 %, elle est applicable aux carburants utilisés par les véhicules à moteur diesel et par des applications de
chauffage conçus ou adaptés pour fonctionner avec 100 % d’EMAG.
NOTE Dans le cadre de la présente Norme européenne, les termes «% (m/m)» et «% (V/V)» sont utilisés pour désigner
respectivement la fraction massique, µ, et la fraction volumique, φ.

Goriva za motorna vozila - Metilni estri maščobnih kislin (FAME) za dizelske motorje in ogrevanje - Zahteve in preskusne metode

Dopolnilo k standardu, ki se nanaša na goriva za motorna vozila – metilni estri maščobnih kislin (FAME) za dizelske motorje – zahteve in preskusne metode.

General Information

Status
Withdrawn
Publication Date
07-Jan-2014
Withdrawal Date
19-Feb-2019
ICS
75.160.20 - Liquid fuels
75.160.40 - Biofuels
Technical Committee
CEN/TC 19 - Petroleum products, lubricants and related products
Drafting Committee
CEN/TC 19/WG 24 - Specification for automotive diesel
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
20-Feb-2019
Directive
98/70/EC - Quality of petrol and diesel fuels (Dir. 93/12/EEC amendment)
Mandate
M/245 - Mandate to CEN for the elaboration and adoption of standards concerning minimum requirement specifications including test methods for Fatty Acid MethylEster (FAME) as fuel for diesel engines and for space heating
Ref Project
SIST EN 14214:2012+A1:2014 - Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods

Relations

Merged Into
EN 14214:2012+A2:2019 - Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods
Effective Date
18-Jan-2023
Merged From
EN 14214:2012 - Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods
Effective Date
19-Jan-2023
Merged From
EN 14214:2012/FprA1 - Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods
Effective Date
23-Oct-2013
Amended By
EN 14214:2012+A1:2014/FprA2 - Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods
Effective Date
11-Oct-2017
Corrected By
EN 14214:2012+A1:2014/AC:2014 - Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods
Effective Date
10-Sep-2014

Buy Standard

EN 14214:2012+A1:2014EN 14214:2012+A1:2014
PreviousNext
Standard
EN 14214:2012+A1:2014
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flüssige Mineralölerzeugnisse - Fettsäure-Methylester (FAME) zur Verwendung in Dieselmotoren und als Heizöl - Anforderungen und PrüfverfahrenProduits pétroliers liquides - Esters méthyliques d'acides gras (EMAG) pour moteurs diesel et comme combustible de chauffage - Exigences et méthodes d'essaiLiquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods75.160.20Liquid fuelsICS:Ta slovenski standard je istoveten z:EN 14214:2012+A1:2014SIST EN 14214:2012+A1:2014en,fr,de01-marec-2014SIST EN 14214:2012+A1:2014SLOVENSKI
STANDARD



SIST EN 14214:2012+A1:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14214:2012+A1
January 2014 ICS 75.160.20 Supersedes EN 14214:2012
English Version
Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods
Produits pétroliers liquides - Esters méthyliques d'acides gras (EMAG) pour moteurs diesel et comme combustible de chauffage - Exigences et méthodes d'essai
Flüssige Mineralölerzeugnisse - Fettsäure-Methylester (FAME) zur Verwendung in Dieselmotoren und als Heizöl - Anforderungen und Prüfverfahren This European Standard was approved by CEN on 20 July 2012 and includes Amendment 1 approved by CEN on 10 November 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14214:2012+A1:2014 E SIST EN 14214:2012+A1:2014



EN 14214:2012+A1:2014 (E)
2 Contents Page Foreword . 3 Introduction . 5 1 Scope . 6 2 Normative references . 6 3 Sampling . 8 4 Pump marking . 8 5 Requirements and test methods . 8 5.1 Dyes and markers . 8 5.2 Additives . 8 5.2.1 General . 8 5.2.2 Oxidation stability enhancing additives . 8 5.2.3 Non-FAME components . 9 5.3 Generally applicable requirements and related test methods . 9 5.4 Climate dependent requirements and related test methods .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TR 17225:2018(Main)
Fuels and biofuels - Assessment on oxidation stability determination methods for distillate fuels and blends thereof with fatty acid methyl esters (FAME)
SIST-TP CEN/TR 17225:2018

This document provides an overview of existing oxidation stability methods, with an emphasis on differences between the Rancimat (EN 14112/EN 15751) and PetroOxy (EN 16091) tests.

  • Technical report
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16934:2017(Main)
Automotive fuels and fat and oil derivates - Determination of steryl glycosides in fatty acid methyl esters (FAME) - Method by GC-MS with prior purification by SPE
SIST EN 16934:2017

This European Standard describes a procedure for the determination of steryl glycosides (SG) contents in fatty acid methyl ester (FAME) in a range between 20 mg/kg and 38 mg/kg.
NOTE   Steryl glycosides (SG) are mainly present in vegetable oils.
WARNING - The use of this standard can involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of users of this standard to take appropriate measures to ensure the safety and health of personnel prior to application of the standard, and fulfil statutory and regulatory requirements for this purpose.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16900:2017(Main)
Fast pyrolysis bio-oils for industrial boilers - Requirements and test methods
SIST EN 16900:2017

This European Standard specifies requirements and test methods for fast pyrolysis bio-oils for boiler use at industrial scale (>1 MW thermal capacity), not for domestic use. Two different grades are specified.
It is recommended to draw attention to differences especially in those properties, which can have an effect on the required flue gas treatment system, such as ash, nitrogen, and sulfur content. National and local regulations determine the requirements for flue gas treatment system.
In addition to the quality requirements and test methods for fast pyrolysis bio-oils, further instructions on storage (Annex A), sampling, and materials compatibility (Annex B) are given.
NOTE   For the purposes of this European Standard, the term "% (m/m)" is used to represent respectively the mass fraction.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16270:2015(Main)
Automotive fuels - Determination of high-boiling components including fatty acid methyl esters in petrol and ethanol (E85) automotive fuel - Gas chromatographic method
SIST EN 16270:2015

This European Standard specifies a determination method of high boiling components in petrol according to EN 228 [1] and ethanol automotive fuels according to CEN/TS 15293 [2] by capillary gas chromatography using flame ionization detection. This method is applicable to high boiling material, such as fatty acid methyl ester (FAME) or diesel fuel, having a boiling point greater than or equal to 1-methyl-naphthalene.
The standard is applicable to materials having a vapour pressure low enough to permit sampling at ambient temperature and a boiling range of at least 100 °C. This method pays special attention to fatty acid methyl esters.
In petrol the measurement range for the high boiling fraction is from about 0,7 % (m/m) to about 2,5 % (m/m). For the FAME fraction the range is from about 0,2 % (m/m) to about 2 % (m/m).
In ethanol automotive fuel the measurement range is from about 0,2 % (m/m) to about 2,2 % (m/m), for the FAME fraction the range is from about 0,05 % (m/m) to about 1,5 % (m/m)
NOTE 1   When calculating the FAME fraction, this method only takes the C18-isomers into account.
NOTE 2   For the purposes of this European Standard, the terms "% (m/m)" and "% (V/V)" are used to represent respectively the mass fraction and the volume fraction.
WARNING -The use of this European Standard may involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15751:2014(Main)
Automotive fuels - Fatty acid methyl ester (FAME) fuel and blends with diesel fuel - Determination of oxidation stability by accelerated oxidation method
SIST EN 15751:2014

This European Standard specifies a test method for the determination of the oxidation stability of fuels for diesel engines, by means of measuring the induction period of the fuel up to 48 h. The method is applicable to fatty acid methyl esters (FAME) intended for the use as pure biofuel or as a blending component for diesel fuels, and to blends of FAME with diesel fuel containing 2 % (V/V) of FAME at minimum.
NOTE 1   EN 14112 [1] describes a similar test method for oxidation stability determination of pure fatty acid methyl esters (see the Introduction to this European Standard).
NOTE 2   For induction periods higher than 48 h the precision is not covered by the precision statement of this method. The limit values of the relevant fuel standards are well within the scope of this test method.
NOTE 3   The presence of cetane improver can reduce the oxidation stability determined by this test method. Limited studies with EHN (2-ethyl hexyl nitrate) indicated, however, that the stability is reduced to an extent which is within the reproducibility of the test method.
NOTE 4   For the purposes of this European Standard, the term "% (V/V)" is used to represent the volume fraction (φ) of a material.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12662:2014(Main)
Liquid petroleum products - Determination of total contamination in middle distillates, diesel fuels and fatty acid methyl esters
SIST EN 12662:2014

This European Standard specifies a method for the determination of the content of undissolved substances, referred to as total contamination, in middle distillates, in diesel fuels containing up to 30 % (V/V) fatty acid methyl esters (FAME), and in neat FAME. The working range is from 12 mg/kg to 30 mg/kg and it was established in an interlaboratory study by applying EN ISO 4259 [2].
This European Standard in general applies to products having a kinematic viscosity not exceeding 8 mm2/s at 20 °C, or 5 mm2/s at 40 °C, e.g. diesel fuel as specified in EN 590 [1].
This test method may be used for diesel fuels containing more than 30 % (V/V) FAME and for petroleum products having a kinematic viscosity exceeding 8 mm2/s at 20 °C, or 5 mm2/s at 40 °C, however in such cases the precision of the test method is not defined.
NOTE 1   Excessive contamination in a fuel system can give rise to premature blocking of filters and/or hardware failure, and is therefore undesirable.
NOTE 2   For the purposes of this European Standard, the term "% (V/V)" is used to represent the volume fraction, φ, of a material.
WARNING - Use of this standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15779:2009+A1:2013(Main)
Petroleum products and fat and oil derivates - Fatty acid methyl esters (FAME) for diesel engines - Determination of polyunsaturated (≥4 double bonds) fatty acid methyl esters (PUFA) by gas chromatography
SIST EN 15779:2009+A1:2013

This European Standard specifies a method for the determination of the polyunsaturated (≥ 4 double bonds) fatty acid (PUFA) methyl esters content of fatty acid methyl ester (FAME) as a whole between 0,6 % (m/m) and 1,5 % (m/m).
The method covers the predominant four polyunsaturated fatty acid methyl esters of eicosatetraenoic acid (C 20:4 (n-6)), eicosapentaenoic acid (C 20:5 (n-3)), docosapentaenoic acid (C 22:5 (n 3), and docosahexaenoic acid (C 22:6 (n 3)).
Studies have indicated that based on the linearity of results from this European Standard, PUFA methyl esters can be determined in FAME in the range between 0,3 % (m/m) to 3,0 % (m/m). However, the precision was not established in that range, as no samples within the upper ranges where included in the final interlaboratory test (see 10.1).
Although the method is applicable to all uses, it is predominantly for FAME for use in diesel engines.
NOTE 1   For the purposes of this document, the term “% (m/m)” is used to represent the mass fraction of a material.
NOTE 2   This European Standard is based on A.O.C.S Official Method Ce 1b-89 [1].

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16557:2013(Main)
Automotive fuels - High FAME diesel fuel blends (B11 - B30) - Background to the parameters required and their respective limits and determination
SIST-TP CEN/TR 16557:2013

This Technical Report provides background information to the deliberations within CEN that led to establish a specification for blending from more than 10 % (V/V) up to 30 % (V/V) of fatty acid methyl ester (FAME) in diesel fuel to be used in captive fleet application for designated vehicles. It gives guidance and explanations to the producers, blenders, marketers and users of high FAME diesel blends (B11 to B30).
The sole designation "Bxx" refers to a FAME-diesel blend where "xx" is the specific FAME content in volume percentage. The connotation "Byy fuel" is used in this document for a fuel with a defined range of FAME allowed and having "yy" volume percentage of FAME content as the maximum of that range.
NOTE   For the purposes of this document, the term “% (m/m)” and “% (V/V)” are used to represent the mass fraction, µ, and the volume fraction, φ, respectively.

  • Technical report
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16294:2012(Main)
Petroleum products and fat and oil derivatives - Determination of phosphorus content in fatty acid methyl esters (FAME) - Optical emission spectral analysis with inductively coupled plasma (ICP OES)
SIST EN 16294:2013

This European Standard specifies an inductively coupled plasma optical emission spectrometry (ICP OES) method for the determination of phosphorus content of Fatty Acid Methyl Esters (FAME) in the range of 2,5 mg/kg to 8,0 mg/kg.
WARNING - The use of this standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16300:2012(Main)
Automotive fuels - Determination of iodine value in fatty acid methyl esters (FAME) - Calculation method from gas chromatographic data
SIST EN 16300:2012

This European Standard specifies a calculation procedure for the determination of Iodine value ("CIV" - "calculated iodine value"), of fatty acid methyl esters (FAME) to be used either as automotive or heating fuel for diesel engines as specified in EN 14214 [2] or as an extender for automotive fuel for diesel engines as specified in EN 590 [4].
This procedure has originally been described in Annex B of EN 14214:2008 [2]. The calculation procedure is now specified for methyl esters between C14 and C24. The calculation procedure uses as data entry the results from the gas chromatography determination (GC) according to EN 14103 of individual fatty acid methyl esters and is based on AOCS recommended practice Cd 1c – 85 for the determination of the iodine value of edible oil from its fatty acid composition. It is important to recognise that the latest version of EN 14103 is to be used for the determination of individual FAME components.
NOTE 1   Experience from the field and from several precision evaluation campaigns in Germany and elsewhere indicates that the results of the determination of iodine value by calculation specified here are very close to results obtained by titration with Wijs solvent according to EN 14111. Observed small differences were always found to be smaller than the reproducibility published in the actual EN 14111.
For informative purposes only, but not for cases of dispute, EN 14331 [5] may also be used to extract the FAME contents from FAME containing diesel fuels (like B5, B7, B30, etc.) and to use the contents of the individual FAME components from this method as data entry for the calculation specified in this European Standard.
In principle, other fatty acid alkyl esters can also be analysed. However, neither the close correlation to the titration method EN 14111 has been verified nor is any precision information available for such an extension of application range.
NOTE 2   For the purposes of this European Standard, the term "% (m/m)" is used to represent the mass fraction, µ, of a material.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day