EN ISO 12625-5:2005

Tissue paper and tissue products - Part 5: Determination of wet tensile strength (ISO 12625-5:2005)

ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.

Tissue-Papier und Tissue-Produkte - Teil 5: Bestimmung der breitenbezogenen Nassbruchkraft (ISO 12625-5:2005)

Dieser Teil der ISO 12625 legt ein Prüfverfahren zur Bestimmung der breitenbezogenen Nassbruchkraft von Tissue-Papier und Tissue-Produkten nach dem Wässern fest. Hierfür wird ein Zugprüfgerät, das mit konstanter Dehngeschwindigkeit arbeitet, verwendet.
Momentan sind zwei Arten von Zugprüfgeräten im Handel erhältlich. Bei dem einen Zugprüfgerät wird die Probe vertikal, beim anderen horizontal positioniert. Dieser Teil der ISO 12625 gilt für beide. Bei vertikalen Zugprüfgeräten erfolgt das Wässern mit Hilfe eines Gerätes, das in der unteren Einspannklemme des Zugprüfgerätes, der so genannten Finch-Eintauchvorrichtung, eingespannt wird. Bei horizontalen Zugprüfgeräten wird die Eintauchvorrichtung zwischen die Klemmen platziert.
Darüber hinaus wird ausdrücklich darauf hingewiesen, dass zur Erkennung von Unreinheiten und Verunreinigungen in Tissue-Papier und Tissue-Produkten ISO 15755 angewendet werden sollte:
Für die Bestimmung des Feuchtegehaltes in Tissue-Papier und Tissue-Produkten sollte ISO 287 angewendet werden.

Papier tissu et produits en tissu - Partie 5: Détermination de la résistance à la rupture par traction à l'état humide (ISO 12625-5:2005)

L'ISO 12625-5:2005 spécifie une méthode d'essai pour la détermination de la résistance à la rupture par traction à l'état humide du papier tissue et des produits tissues, après immersion dans l'eau, en utilisant un appareil d'essai de traction fonctionnant à une vitesse d'allongement constante.

Tissue papir in proizvodi iz tissue papirja - 5. del: Ugotavljanje mokre natezne trdnosti (ISO 12625-5:2005)

General Information

• Status: Withdrawn
• Publication Date: 14-Apr-2005
• Withdrawal Date: 20-Dec-2016
• ICS: 85.080 - Paper products
• Technical Committee: CEN/TC 172 - Pulp, paper and board
• Drafting Committee: CEN/TC 172/WG 8 - Test methods for soft tissue papers
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 21-Dec-2016
• Ref Project: SIST EN ISO 12625-5:2005 - Tissue paper and tissue products - Part 5: Determination of wet tensile strength (ISO 12625-5:2005)

Relations

• Replaces: EN 12625-5:1999 - Tissue paper and tissue products - Part 5: Determination of wet tensile strength
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 12625-5:2016 - Tissue paper and tissue products - Part 5: Determination of wet tensile strength (ISO 12625-5:2016)
• Effective Date: 28-Dec-2016

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2005
1DGRPHãþD
SIST EN 12625-5:2000
Tissue papir in proizvodi iz tissue papirja - 5. del: Ugotavljanje mokre natezne
trdnosti (ISO 12625-5:2005)
Tissue paper and tissue products - Part 5: Determination of wet tensile strength (ISO
12625-5:2005)
Tissue-Papier und Tissue-Produkte - Teil 5: Bestimmung der breitenbezogenen
Nassbruchkraft (ISO 12625-5:2005)
Papier tissu et produits en tissu - Partie 5: Détermination de la résistance a la rupture par
traction a l'état humide (ISO 12625-5:2005)
Ta slovenski standard je istoveten z: EN ISO 12625-5:2005
ICS:
85.080.20 Tissue papir Tissue paper
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 12625-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2005
ICS 85.080 Supersedes EN 12625-5:1999
English version
Tissue paper and tissue products - Part 5: Determination of wet
tensile strength (ISO 12625-5:2005)
Papier tissu et produits en tissu - Partie 5: Détermination Tissue-Papier und Tissue-Produkte - Teil 5: Bestimmung
de la résistance à la rupture par traction à l'état humide der breitenbezogenen Nassbruchkraft (ISO 12625-5:2005)
(ISO 12625-5:2005)
This European Standard was approved by CEN on 21 March 2005.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12625-5:2005: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 12625-5:2005) has been prepared by Technical Committee CEN/TC 172
"Pulp, paper and board", the secretariat of which is held by DIN, in collaboration with Technical
Committee ISO/TC 6 "Paper, board and pulps”.

This document supersedes EN 12625-5:1999.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by October 2005, and conflicting national
standards shall be withdrawn at the latest by October 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
INTERNATIONAL ISO
STANDARD 12625-5
First edition
2005-04-15
Tissue paper and tissue products
Part 5:
Determination of wet tensile strength
Papier tissu et produits en tissu
Partie 5: Détermination de la résistance à la rupture par traction à l'état
humide
Reference number
ISO 12625-5:2005(E)
©
ISO 2005
ISO 12625-5:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved

ISO 12625-5:2005(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 2
4 Principle . 2
5 Apparatus. 2
6 Conditioning . 5
7 Preparation . 5
8 Procedure. 6
9 Calculation. 9
10 Test report. 9
11 Precision . 10
Bibliography . 12

ISO 12625-5:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12625-5 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 172, Pulp, paper and board, in collaboration with Technical Committee ISO/TC 6, Paper, board and
pulps, Subcommittee SC 2, Test methods and quality specifications for paper and board, in accordance with
the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This first edition cancels and replaces EN 12625-5:1999 which has been technically revised.
With regard to EN 12625-5:1999, the following changes have been made:
a) addition of information concerning the precision of the test method;
b) editorial updating.
ISO 12625 consists of the following parts, under the general title Tissue paper and tissue products:
 Part 1: General guidance on terms
 Part 3: Determination of thickness, bulking thickness and apparent bulk density
 Part 4: Determination of tensile strength, stretch at break and tensile energy absorption
 Part 5: Determination of wet tensile strength
 Part 6: Determination of grammage
 Part 7: Determination of optical properties
 Part 8: Water absorption time and water absorption capacity, basket immersion test method
 Part 9: Determination of ball burst strength
iv © ISO 2005 – All rights reserved

INTERNATIONAL STANDARD ISO 12625-5:2005(E)

Tissue paper and tissue products
Part 5:
Determination of wet tensile strength
1 Scope
This part of ISO 12625 specifies a test method for the determination of the wet tensile strength of tissue paper
and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant
rate of elongation.
Currently, two types of tensile-strength testers are commercially available, one where the test piece is positioned
vertically and, for the other, horizontally. This part of ISO 12625 applies for both. For vertical tensile-strength
testers, a device which is held in the lower grip of the tensile-strength tester, called a Finch Cup, is used to
achieve the wetting. For horizontal tensile-strength testers, the soaking device is placed between the clamps.
It is expressly stated that the detection of impurities and contraries in tissue paper and tissue products should
be applied according to ISO 15755.
For the determination of moisture content in tissue paper and tissue products, ISO 287 should be applied.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 186, Paper and board — Sampling to determine average quality
ISO 187, Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for
monitoring the atmosphere and conditioning of samples
ISO 1924-2, Paper and board — Determination of tensile properties — Part 2: Constant rate of elongation
method
ISO 7500-1, Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression
testing machines — Verification and calibration of the force-measuring system
ISO 12625-1, Tissue paper and tissue products — Part 1: General guidance on terms
ISO 12625-4, Tissue paper and tissue products — Part 4: Determination of tensile strength, stretch at break and
tensile energy absorption
ISO 12625-5:2005(E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 12625-1 and the following apply.
3.1
wet tensile strength
maximum tensile force per unit width that a test piece soaked with water will withstand before breaking in a
tensile test
NOTE The wet tensile strength is expressed in newtons per metre.
3.2
wet-tensile-strength retention
ratio, expressed as a percentage, of the tensile strength of the wet test piece to the tensile strength of the
same test piece in the dry, conditioned state
4 Principle
A test piece of tissue paper or tissue product of given dimensions, soaked in water for a given period of time
under specified conditions, is stretched (elongated) to break at a constant rate of elongation, using a
tensile-strength-testing apparatus that measures and records the tensile force as a function of the elongation of
the test piece.
The test can be carried out by a vertical or a horizontal tensile-strength tester.
In order to wet the test pieces for a vertical tensile-strength tester, a device, called a Finch Cup, which is held
to the lower clamp, is used; while for a horizontal tensile-strength tester, a soaking cup is inserted between the
clamps.
From the wet tensile strength and the tensile strength of the same sample in the dry conditioned state, the
wet-tensile-strength retention can be calculated.
5 Apparatus
5.1 Vertical tensile-strength tester
5.1.1 Tensile-strength-testing apparatus
Tensile-strength-testing apparatus shall be in accordance with ISO 1924-2. It is capable of stretching a test
piece of tissue paper or tissue product of given dimensions, at a constant rate of elongation of
(50 ± 2) mm/min, and recording the tensile force as a function of elongation on a strip chart recorder or any
equivalent device.
The force-measuri
...