CEN/TC 172/WG 8 - Test methods for soft tissue papers

This document specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
Currently, two types of tensile-strength-testing apparatus are commercially available, one where the test piece is positioned vertically and, for the other, horizontally. This document applies for both. For vertical tensile-strength-testing apparatus, a device that is held in the lower grip of the tensile-strength-testing apparatus, called a Finch Cup, is used to achieve the wetting. For horizontal tensile-strength-testing apparatus, the soaking device is placed between the two clamps.
This document is not applicable to cases where impurities and contraries are determined.

This document specifies the testing procedures for the instrumental determination of the opacity of tissue paper or tissue products by diffuse reflectance using a paper backing.
This document contains specific instructions for the preparation of test pieces of single-ply and multi-ply products, where special preparation/procedures might be necessary.
It can be used to determine the opacity of tissue paper and tissue products containing fluorescent whitening agents, provided the UV content of the radiation incident on the test piece has been adjusted to conform to that in the CIE illuminant C using a fluorescent reference standard provided by an authorized laboratory as described in ISO 2470-1.

This document specifies a test method for the determination of the tensile strength of perforated lines of tissue paper. It uses a tensile-testing apparatus operating with a constant rate of elongation.
This method is only used for measuring machine-direction tensile strength, that is for cross-direction perforations on tissue paper.
The calculation of perforation efficiency is also specified in this document.

This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed in indoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary.
NOTE      The properties called D65 brightness and colour are measured with an instrument adjusted to a much higher UV content than that specified in this document.

This document specifies a test method for the determination of the tensile strength, stretch at maximum force and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation.
It also specifies the method of calculating the tensile index and the tensile energy absorption index.

This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed under outdoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary.
NOTE       The properties called ISO brightness and colour with C/2° (indoor daylight) are measured with an instrument adjusted to a much lower UV content than that specified in this document. The measurements of ISO brightness and colour with C/2° (indoor daylight) are described in ISO 12625-15.

This document specifies a method to assess the disintegration of tissue paper and tissue products when subjected to mechanical agitation in water.

This document establishes general principles for the use of terms in the entire working field of tissue paper and tissue products.
It permits the use of a common terminology in industry and commerce.
It is expressly stated that ISO 15755 applies for the detection of impurities and contraries in tissue paper and tissue products.
For the determination of moisture content in tissue paper and tissue products, ISO 287 applies.

ISO 12625-6:2016 specifies a test method for the determination of grammage of tissue paper and tissue products.

ISO 12625-9:2015 specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products.
Currently, two types of clamping devices are available on the market with two different diameters, one is with 50 mm and one is with 89 mm. ISO 12625-9:2015 applies for a 50 mm clamping device to be able to measure all sample sizes of tissue paper and tissue products and to be consistent with ISO 12625-11.

ISO 12625-3:2014 specifies a test method for the determination of thickness and bulking thickness and the calculation of apparent bulk density and bulk of tissue papers and tissue products under a pressure of 2,0 kPa.

ISO 12625-8:2010 specifies a basket-immersion test method for the determination of water-absorption time and water-absorption capacity of tissue paper and tissue products.
It is expressly stated that the detection of impurities and contraries in tissue paper and tissue products be applied according to ISO 15755.
For the determination of moisture content in tissue paper and tissue products, ISO 287 is applicable.

ISO 12625-5:2016 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
Currently, two types of tensile-strength-testing apparatus are commercially available, one where the test piece is positioned vertically and, for the other, horizontally. This document applies for both. For vertical tensile-strength-testing apparatus, a device which is held in the lower grip of the tensile-strength-testing apparatus, called a Finch Cup, is used to achieve the wetting. For horizontal tensile-strength-testing apparatus, the soaking device is placed between the clamps.
In cases where impurities and contraries have to be determined, ISO 15755[6] applies for these detections in tissue paper and tissue products.

ISO 12625-16:2015 specifies the testing procedures for the instrumental determination of the opacity of tissue paper or tissue products by diffuse reflectance using a paper backing.
ISO 12625-16:2015 contains specific instructions for the preparation of test pieces of single-ply and multi-ply products, where special preparation/procedures might be necessary.
It can be used to determine the opacity of tissue paper and tissue products containing fluorescent whitening agents, provided the UV content of the radiation incident on the test piece has been adjusted to conform to that in the CIE illuminant C using a fluorescent reference standard provided by an authorized laboratory as described in ISO 2470-1.
ISO 12625-16:2015 is not applicable to coloured tissue paper and tissue products which incorporate fluorescent dyes or pigments.

ISO 12625-12:2010 specifies a test method for the determination of the tensile strength of perforated lines of tissue paper. It uses a tensile-testing apparatus operating with a constant rate of elongation.
This method is only used for measuring machine-direction tensile strength, that is for cross-direction perforations on tissue paper.
The calculation of perforation efficiency is also specified in ISO 12625-12:2010.

ISO 12625-15:2015 specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed in indoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions may be necessary.

ISO 12625-4:2016 specifies a test method for the determination of the tensile strength, stretch at maximum force and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation.
It also specifies the method of calculating the tensile index and the tensile energy absorption index.
In cases where impurities and contraries have to be determined, ISO 15755[6] applies for these detections in tissue paper and tissue products.

ISO 12625-7:2014 specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed under outdoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions may be necessary.

ISO 12625-11:2012 specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products after wetting.

ISO 12625-1:2011 establishes general principles for the use of terms in the entire working field of tissue paper and tissue products.
It permits the use of a common terminology in industry and commerce.

ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.

ISO 12625-4:2005 specifies a test method for the determination of the tensile strength, stretch at break and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation.
It also specifies the method of calculating the tensile index and the tensile energy absorption index.

ISO 12625-6:2005 specifies a test method for the determination of grammage of tissue paper and tissue products. Grammage may be measured by determining the mass of a test piece or test pieces of tissue paper or tissue products cut to specified dimensions, or by determining the mass and area of a specified number of units of finished tissue products.

ISO 12625-9:2005 specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products.

ISO 12625-7:2007 specifies test methods for the instrumental determination of optical properties of tissue paper and tissue products. The various test methods that are available have been, or are being, developed as International Standards.
ISO 12625-7:2007 also gives recommendations regarding relevant optical properties to be measured for different grades of tissue paper and tissue products and gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of creped products and embossed products, where special precautions may be necessary if the test-piece surfaces are uneven and if the materials are bulky, so that air is entrapped between the sheets.

ISO 12625-3:2005 specifies a test method for the determination of thickness and bulking thickness, and the calculation of apparent bulk density, of tissue paper and tissue products under a pressure of 2,0 kPa.

ISO 12625-1:2005 establishes general principles for the use of terms in the entire working field of tissue paper and tissue products.
It permits the use of a common terminology in industry and commerce.
It is expressly stated that the detection of impurities and contraries in tissue paper and tissue products should be applied according to ISO 15755.
For the determination of moisture content in tissue paper and tissue products, ISO 287 should be applied.
In addition to terms in English and French (two of the three official ISO languages), ISO 12625-1:2005 gives the equivalent terms in German; these are published under the responsibility of the member body for Germany (DIN). However, only the terms and definitions given in the official languages can be considered as ISO terms and definitions.

CMC - Incomplete superseding note

ISO 12625-8:2006 specifies basket-immersion test methods (one manual and one automated) for the determination of water-absorption time and water-absorption capacity of absorbent tissue paper and tissue products.

This part of EN 12625 specifies the test methods that shall be used for the instrumental determination of optical properties of tissue paper and tissue products. It also gives recommendations regarding relevant optical properties to be measured for different grades of tissue
paper and tissue products and gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of creped products and embossed products, where special precautions may be necessary if the test pieces surfaces are uneven and if the materials are bulky so that air is entrapped between the sheets.

The purpose of this part of EN 12625 is to determine, on the same sample: - water absorption rate; - water absorption capacity. This test method covers the evaluation of the behaviour of tissue paper and tissue products in the presence of water.

This part of prEN 12625 specifies a test method for the determination of the tensile strength, stretch at break and tensile energy absorption of tissue paper and tissue products using a tensile testing apparatus operating with a constant rate of elongation. This European Standard also specifies the method of calculating the tensile index and the tensile energy absorption index.

This part of prEN 12625 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after wetting using a tensile testing apparatus operating with a constant rate of elongation.

This part of prEN 12625 specifies a test method for the determination of thickness, bulking thickness and apparent bulk density of tissue papers and tissue products when under a specified pressure of 2,0 kPa. Note: This European Standard has been developed to provide a consistent test method for the determination of certain properties of tissue paper and tissue products. Corresponding test methods for paper and board in general are covered in EN 20534.

This part of prEN 12625 specifies a test method for the determination of grammage of tissue paper and tissue products.

This part of EN 12625 (currently only available as a European Prestandard) specifies procedures for sampling and conditioning of tissue paper and tissue products.