EN ISO 6402-2:1999

Plastics - Impact-resistant acrylonitrile/styrene (ASA, AES, ACS) moulding and extrusion materials, excluding butadiene-modified materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:1994)

Kunststoffe - Schlagzähe Acrylnitril/Styrol (ASA, AES, ACS)-Formmassen, außer Butadien-modifizierten Materialien - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 6402-2:1994)

Dieser Teil von ISO 6402 legt die Bedingungen zur Herstellung von Probeko(rpern und die zur Bestimmung der Eigenschaften von ASA, AES, ACS-Formmassen anzuwendenden Pru(fverfahren fest. Anforderungen an die Behandlung des Probenmaterials und fu(r das Konditionieren des Probenmaterials vor der Herstellung der Probeko(rper und der Probeko(rper vor der Pru(fung sind ebenfalls enthalten.

Plastiques - Thermoplastiques à base d'acrylonitrile/styrène sans butadiène (ASA, AES, ACS), résistant au choc, pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 6402-2:1994)

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz proti udarcem odpornih kopolimerov akrilonitril/stiren (ASA, AES, ACS), razen materialov, modificiranih z butadienom - 2. del: Priprava preskušancev in določanje lastnosti (ISO 6402-2:1994)

General Information

• Status: Withdrawn
• Publication Date: 18-May-1999
• Withdrawal Date: 30-Nov-2003
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249/SC 1/WG 9 - Styrenics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 01-Dec-2003
• Completion Date: 01-Dec-2003
• Ref Project: SIST EN ISO 6402-2:2000 - Plastics - Impact-resistant acrylonitrile/styrene (ASA, AES, ACS) moulding and extrusion materials, excluding butadiene-modified materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:1994)

Relations

• Replaced By: EN ISO 6402-2:2003 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:2003)
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 6402-2:2000
01-maj-2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]SURWLXGDUFHP
RGSRUQLKNRSROLPHURYDNULORQLWULOVWLUHQ$6$$(6$&6UD]HQPDWHULDORY
PRGLILFLUDQLK]EXWDGLHQRPGHO3ULSUDYDSUHVNXãDQFHYLQGRORþDQMHODVWQRVWL
,62
Plastics - Impact-resistant acrylonitrile/styrene (ASA, AES, ACS) moulding and extrusion
materials, excluding butadiene-modified materials - Part 2: Preparation of test specimens
and determination of properties (ISO 6402-2:1994)
Kunststoffe - Schlagzähe Acrylnitril/Styrol (ASA, AES, ACS)-Formmassen, außer
Butadien-modifizierten Materialien - Teil 2: Herstellung von Probekörpern und
Bestimmung von Eigenschaften (ISO 6402-2:1994)
Plastiques - Thermoplastiques a base d'acrylonitrile/styrene sans butadiene (ASA, AES,
ACS), résistant au choc, pour moulage et extrusion - Partie 2: Préparation des
éprouvettes et détermination des propriétés (ISO 6402-2:1994)
Ta slovenski standard je istoveten z: EN ISO 6402-2:1999
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 6402-2:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 6402-2:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 6402-2:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 6402-2:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 6402-2:2000

---------------------- Page: 5 ----------------------

SIST EN ISO 6402-2:2000

---------------------- Page: 6 ----------------------

SIST EN ISO 6402-2:2000
INTERNATIONAL
ISO
STANDARD
6402-2
First edition
1994-11-01
Plastics - Impact-resistant
acrylonitrile/styrene (ASA, AES, ACS)
moulding and extrusion materials,
excluding butadiene-modified materials -
Part 2:
Preparation of test specimens and
determination of properties
Plas tiques - Thermoplastiques 3 base d ’acrylonitrile/styr&ne sans
butadiene (ASA, AES, ACS), kistants au choc, pour moulage et
extrusion -
Partie 2: Prepara tion des eprouve ttes et d&ermina tion des propri&&
Reference number
ISO 64022:1994(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 6402-2:2000
ISO 6402-2: 1994(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 6402-2 was prepared by Technical Committee
lSO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.
ISO 6402 consists of the following Parts, under the general title
Plas tics - Impact-resistant acrylonitrilelstyrene (ASA, AES, ACS) mould-
ing and extrusion ma terials, excluding butadiene-modified ma terials:
- Part 1: Designation
- Part 2: Preparation of test specimens and determination of proper-
ties
Annex A forms an integral part of this part of ISO 6402.
0 ISO 1994
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, efectronic or mechanical, including photocopying and
microfilm, without Permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1 211 Geneve 20 l Switzerland
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 6402-2:2000
INTERNATIONAL STANDARD 0 ISO ISO 6402-2: 1994(E)
- Impact-resistant acrylonitrile/styrene (ASA,
Plastics
AES, ACS) moulding and extrusion materials,
excluding butadiene-modified materials -
Part 2:
Preparation of test specimens and determination of
properties
2 Normative references
1 Scope
This part of ISO 6402 specifies the methods of prep-
The following Standards contain provisions which,
aration of test specimens and the test methods to be
through reference in this text, constitute provisions
used in determining the properties of ASA, AES, ACS
of this part of ISO 6402. At the time of publication, the
moulding and extrusion materials. Requirements for
editions indicated were valid. All Standards are subject
handling test material and for conditioning both the
to revision, and Parties to agreements based on this
test material before moulding and the specimens be-
patt of ISO 6402 are encouraged to investigate the
fore testing are given here.
possibility of applying the most recent editions of the
Standards indicated below. Members of IEC and ISO
Procedures and conditions for the preparation of test
maintain registers of currently valid International
specimens and procedures for measuring properties
Standards.
of the materials from which these specimens are
made are given. Properties and test methods which
ISO 62:1980, Plastics - Determination of wa ter ab-
are suitable and necessary to characterize ASA, AES,
sorp tion.
ACS moulding and extrusion materials are listed.
ISO 75-1: 1993, Plastics - Determination of tempera-
The properties have been selected from the general
ture of deflection under load - Part 7: General test
test methods in ISO 10350. Other test methods in
method.
wide use for or of particular significance to these
moulding and extrusion materials are also included in
ISO 75-2: 1993, Plastics - Determination of tempera-
this part of ISO 6402, as are the designatory proper-
ture of deflection under load - Part 2: Plastics and
ties specified in part 1: Vicat softening temperature,
ebonite.
melt flow rate, impact strength and flexural modulus.
ISO 178: 1993, Plastics - Determination of flexural
In Order to obtain reproducible and comparable test
properties.
results, it is necessary to use the methods of speci-
men preparation and conditioning, the specimen di- BS0 179: 1993, PIastics - Determination of Charpy
mensions and the test procedures specified herein impact strength.
Values determined will not necessarily be identical to
ISO 180:1993, Piastics - Determination of I’zod im-
those obtained using specimens of different dimen-
sions or prepared using different procedures. patt strength.

---------------------- Page: 9 ----------------------

SIST EN ISO 6402-2:2000
0 ISO
ISO 6402-2: 1994(E)
ISO 4589-2:-*), Plastics - Determination of
ISO 291 :1977, Plastics - Standard atmospheres for
flammability - Part 2: Determination of Oxygen index
conditioning and testing.
(01) at ambien t tempera ture.
- Compression moulding tes t
ISO 293: 1986, Plastics
-*), Plastics - Determination of burning
ISO 4589-3:
specimens of thermoplastic ma terials.
behaviour by Oxygen index - Part 3: Elevated-
ISO 294: -l 1, Plas tics - Injection moulding of test tempera ture tes t.
specimens of thermoplas tic ma terials.
ISO 6402-1: 1990, Plas tics - Impac t-resis tan t
acrylonitrile/s tyrene moulding and extrusion ma terials
ISO 306: 1994, Plastics - Thermoplastic materials -
excluding butadiene-modified ma-
Determination of Vicat softening temperature (VST). (ASA, AES, ACS),
terials - Part 1: Designation.
ISO 527-1 :1993, Plastics - Determination of tensile
properties - Part 1: General principles. ISO 8256:1990, Plastics - Determination of tensile-
impact strength.
ISO 527-2:1993, Plastics - Determination of tensile
properties - Part 2: Test conditions for moulding and ISO 10350: 1993, Plastics - Acquisition and presen-
extrusion plas tics. ta tion of comparable Single-poin t da ta.
Determination o f tensile
ISO 527-4: -*), Plastics - IEC 93: 1980, Methods of test for volume resistivity
properties - Patt 4: Test conditions for isotropic and and surface resistivity of solid electrical insulating
aniso tropic fibre-rein forced plas tic composites. ma terials.
- Determination of creep
ISO 899-1 :1993, Plastics IEC 112: 1979, Method for determining the compar-
- Part 1: Tensile creep.
behaviour ative and the proof tracking indices of solid insulating
materials under moist conditions.
ISO 1133:1991, Plastics - Determination of the melt
mass-flow rate (MFR) and the melt volume-flow rate IEC 243-1: 1988, Methods of test for electric strength
(M VR) of thermoplas tics. o f solid insula ting ma terials - Part I : Tests at power
frequencies.
ISO 1183:1987, Plastics - Me thods for determining
IEC 250:1969, Recommended methods for the deter-
the density and relative density of non-cellular
plastics. mina tion of t
...