EN ISO 178:2010/A1:2013

Plastics - Determination of flexural properties (ISO 178:2010/Amd 1:2013)

2012-10-10 EMA: Draft for // vote received in ISO/CS (see notification of 2012-10-10 in dataservice).
2011-11-28 EMA: Draft for // ENQ received in ISO/CS (see notification of 2011-11-28 in dataservice).

Kunststoffe - Bestimmung der Biegeeigenschaften (ISO 178:2010/Amd 1:2013)

Plastiques - Détermination des propriétés en flexion (ISO 178:2010/Amd 1:2013)

Polimerni materiali - Določanje upogibnih lastnosti (ISO 178:2010/Amd 1:2013)

Ta mednarodni standard določa metodo za določanje upogibnih lastnosti trdih (glej točko 3.12) in poltrdih polimernih materialov pod določenimi pogoji. Opredeljen je standardni preskušanec, vendar so vključeni parametri za druge velikosti preskušanca, ki se uporabijo, kjer je to primerno. Vključen je razpon preskusnih hitrosti. Ta metoda se uporablja za preučevanje upogibnega obnašanja preskušanca in za določanje upogibne trdnosti, upogibnih modulov in drugih vidikov razmerja med upogibno napetostjo/raztezkov pod opredeljenimi pogoji. Velja za prosto podprt tram, obremenjen na sredini (tritočkovni obremenitveni preskus). Ta metoda je primerna za uporabo pri naslednjih materialih: – plastomerni materiali za brizganje, materiali za iztiskanje in vlivanje, vključno s polnjenimi in ojačanimi spojinami poleg nepolnjenih vrst; trdi plastomerni trakovi; termoreaktivni materiali za brizganje, vključno s polnjenimi in ojačanimi spojinami; termoreaktivni trakovi.

General Information

• Status: Withdrawn
• Publication Date: 19-Mar-2013
• Withdrawal Date: 07-May-2019
• ICS: 83.080.01 - Plastics in general
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 08-May-2019
• Ref Project: SIST EN ISO 178:2011/A1:2014 - Plastics - Determination of flexural properties (ISO 178:2010/Amd 1:2013)

Relations

• Replaced By: EN ISO 178:2019 - Plastics - Determination of flexural properties (ISO 178:2019)
• Effective Date: 15-May-2019
• Amends: EN ISO 178:2010 - Plastics - Determination of flexural properties (ISO 178:2010)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2014
3ROLPHUQLPDWHULDOL'RORþDQMHXSRJLEQLKODVWQRVWL,62$PG
Plastics - Determination of flexural properties (ISO 178:2010/Amd 1:2013)
Kunststoffe - Bestimmung der Biegeeigenschaften (ISO 178:2010/Amd 1:2013)
Plastiques - Détermination des propriétés en flexion (ISO 178:2010/Amd 1:2013)
Ta slovenski standard je istoveten z: EN ISO 178:2010/A1:2013
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 178:2010/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2013
ICS 83.080.01
English Version
Plastics - Determination of flexural properties (ISO
178:2010/Amd 1:2013)
Plastiques - Détermination des propriétés en flexion (ISO Kunststoffe - Bestimmung der Biegeeigenschaften (ISO
178:2010/Amd 1:2013) 178:2010/Amd 1:2013)
This amendment A1 modifies the European Standard EN ISO 178:2010; it was approved by CEN on 19 March 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 178:2010/A1:2013: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 178:2010/A1:2013) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This Amendment to the European Standard EN ISO 178:2010 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting
national standards shall be withdrawn at the latest by September 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 178:2010/Amd 1:2013 has been approved by CEN as EN ISO 178:2010/A1:2013 without any
modification.
INTERNATIONAL ISO
STANDARD 178
Fifth edition
2010-12-15
AMENDMENT 1
2013-04-01
Plastics — Determination of flexural
properties
AMENDMENT 1
Plastiques — Détermination des propriétés en flexion
AMENDEMENT 1
Reference number
ISO 178:2010/Amd.1:2013(E)
©
ISO 2013
ISO 178:2010/Amd.1:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 178:2010/Amd.1:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO colla
...