EN 10152:2003
(Main)Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
1.1 This European Standard specifies requirements for continuously electrolytic zinc coated cold rolled flat products of low carbon steels suitable for cold forming according to Table 1 in rolled widths $ 600 mm and thicknesses from 0,35 mm up to and including 3 mm, delivered as strip (in coil form), sheet, slit strip or cut lengths obtained from slit strip or sheet.
Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen - Technische Lieferbedingungen
Produits plats en acier, laminés à froid, revêtus de zinc par voie électrolytique pour formage à froid - Conditions techniques de livraison
1.1 La présente Norme européenne définit les prescriptions relatives aux produits plats laminés à froid revêtus de zinc en continu par voie électrolytique, en aciers à bas carbone aptes au formage à froid selon les indications du Tableau 1, en largeurs laminées * 600 mm et en épaisseurs comprises entre 0,35 mm et 3 mm inclus, livrés sous forme de bandes (en bobines), de tôles, de bandes refendues ou coupés à longueur dans des bandes refendues ou dans des tôles.
1.2 La présente Norme européenne peut également s'appliquer aux produits plats laminés à froid revêtus de zinc en continu, par voie électrolytique, en :
a) aciers conformes à l'EN 10139 (feuillards laminés à froid en largeur de laminage < 600 mm) ;
b) d'autres types d'aciers à bas carbone pour formage à froid ;
c) aciers normalement caractérisés par une valeur minimale de limite d'élasticité en plus de leur aptitude au formage et par exemple ;
¾ aciers à haute limite d'élasticité et à formabilité améliorée conforme à l'EN 10268 ou autres aciers micro-alliés ;
¾ aciers IF (sans atomes intersticiels) ;
¾ aciers alliés au phosphore et à durcissement différé à la cuisson (bake-hardening) ;
¾ aciers biphasés ;
¾ aciers de construction d'usage général.
1.3 Par accord particulier au moment de l'appel d'offres et à la commande, cette Norme européenne peut être appliquée aux produits plats laminés à chaud revêtus de zinc en continu par voie électrolytique (par exemple, conforme aux EN 10025, EN 10111, EN 10149-1 à EN 10149-3).
1.4 Les masses de revêtement, aspects et finitions de surface sont indiqués en 6.9, 6.11 et au Tableau 2. La masse de zinc déposée étant relativement faible, le matériau n'est pas censé résister à une exposition extérieure sans autre traitement chimique et peinture.
1.5 La présente Norme européenne ne s'applique pas :
¾ aux tôles et bandes en acier galvanisées à chaud (voir EN 10142 et EN 10147) ;
¾ aux produits plats prélaqués (voir EN 10169-1, prEN 10169-2 et prEN 10169-3).
Elektrolizno cinkani hladno valjani ploščati izdelki za hladno preoblikovanje – Tehnični dobavni pogoji
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 10152:2003
01-november-2003
1DGRPHãþD
SIST EN 10152:1997
(OHNWUROL]QRFLQNDQLKODGQRYDOMDQLSORãþDWLL]GHONL]DKODGQRSUHREOLNRYDQMH±
7HKQLþQLGREDYQLSRJRML
Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical
delivery conditions
Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen -
Technische Lieferbedingungen
Produits plats en acier, laminés a froid, revetus de zinc par voie électrolytique pour
formage a froid - Conditions techniques de livraison
Ta slovenski standard je istoveten z: EN 10152:2003
ICS:
77.140.50 3ORãþDWLMHNOHQLL]GHONLLQ Flat steel products and semi-
SROL]GHONL products
SIST EN 10152:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 10152
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2003
ICS 77.140.50 Supersedes EN 10152:1993
English version
Electrolytically zinc coated cold rolled steel flat products for cold
forming - Technical delivery conditions
Produits plats en acier, laminés à froid, revêtus de zinc par Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus
voie électrolytique pour formage à froid - Conditions Stahl zum Kaltumformen - Technische Lieferbedingungen
techniques de livraison
This European Standard was approved by CEN on 21 February 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10152:2003 E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 10152:2003 (E)
Contents
page
Foreword. 3
1 Scope. 3
2 Normative references . 4
3 Terms and definitions. 5
4 Classification and designation . 5
4.1 Classification. 5
4.2 Designation. 5
5 Information to be supplied by the purchaser. 6
6 Requirements . 6
6.1 General . 6
6.2 Steelmaking and manufacturing processes. 7
6.3 Deoxidation. 7
6.4 Chemical composition. 7
6.5 Delivery condition . 7
6.6 Choice of properties . 7
6.7 Mechanical properties . 7
6.8 Stretcher strain marks . 9
6.9 Coatings. 9
6.10 Adhesion of coating. 10
6.11 Surface characteristics. 10
6.12 Surface treatment (surface protection). 10
6.13 Applications. 11
6.14 Mass, tolerances on dimensions and shape. 11
7 Testing. 11
7.1 General . 11
7.2 Test units . 12
7.3 Number of tests. 12
7.4 Sampling . 12
7.5 Test methods. 12
7.6 Retests . 13
7.7 Inspection documents . 13
8 Marking. 13
9 Packing. 13
10 Storage and transportation. 13
Annex A (normative) Reference method for determination of the zinc coating mass . 14
Bibliography . 15
2
---------------------- Page: 3 ----------------------
EN 10152:2003 (E)
Foreword
This document EN 10152:2003 has been prepared by Technical Committee ECISS/TC 27 "Surface coated flat
products - Qualities, dimensions, tolerances and specific tests", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by October 2003, and conflicting national standards shall be withdrawn at the latest
by October 2003.
This document supersedes EN 10152:1993.
Annex A is normative.
This document includes a Bibliography.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,
Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
1 Scope
1.1 This European Standard specifies requirements for continuously electrolytic zinc coated cold rolled flat
products of low carbon steels suitable for cold forming according to Table 1 in rolled widths 600 mm and
thicknesses from 0,35 mm up to and including 3 mm, delivered as strip (in coil form), sheet, slit strip or cut lengths
obtained from slit strip or sheet.
1.2 This European Standard can also be applied to continuously electrolytic zinc coated cold rolled flat products
of
a) steels according to EN 10139 (cold rolled strip in rolled widths < 600 mm),
b) other types of low carbon steel for cold forming,
c) steels normally characterized by minimum yield strength values in addition to formability parameters,
e. g.
steels with high yield strength and improved formability according to EN 10268, or other microalloyed
steels,
high strength IF(without interstitial atoms) steels,
phosphorous alloyed steels and bake-hardening steels,
dual phase steels,
general purpose structural steels.
1.3 By special agreement at the time of enquiry and order this European Standard can be applied to
continuously electrolytic zinc coated hot-rolled steel flat products (e.g. according to EN 10025, EN 10111,
EN 10149-1 to EN 10149-3, etc.).
3
---------------------- Page: 4 ----------------------
EN 10152:2003 (E)
1.4 The coating masses, surface qualities and surface finishes are given in 6.9, 6.11 and Table 2. As the mass
of the zinc coating applied is relatively small, the material is not intended to withstand outside exposure without
further chemical treatment and painting.
1.5 This European Standard is not applicable to
hot-dip zinc coated steel strip and sheet (see EN 10142 and EN 10147);
continuously organic coated steel flat products (see EN 10169-1, ENV 10169-2 and prEN 10169-3).
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 10002-1, Metallic materials - Tensile testing - Part 1: Method of test at ambient temperature.
EN 10020:2000, Definition and classification of grades of steel.
EN 10021:1993, General technical delivery requirements for steel and iron products.
EN 10027-1, Designation systems for steels - Part 1: Steel names; principal symbols.
EN 10027-2, Designation systems for steels - Part 2: Numerical system.
EN 10079:1992, Definition of steel products.
EN 10131, Cold rolled uncoated low carbon and high yield strength steel flat products for cold forming - Tolerances
on dimensions and shape.
EN 10204:1991, Metallic materials - Types of inspection documents.
CR 10260, Designation systems for steel - Additional symbols.
EN ISO 7438, Metallic materials - Bend test (ISO 7438:1985).
ISO 10113, Metallic materials - Sheet and strip - Determination of plastic strain ratio.
ISO 10275, Metallic materials - Sheet and strip - Determination of tensile strain hardening exponent.
4
---------------------- Page: 5 ----------------------
EN 10152:2003 (E)
3 Terms and definitions
For the purposes of this European Standard the terms and definitions given in EN 10020:2000, EN 10021:1993,
EN 10079:1992 and EN 10204:1991 and the following apply.
3.1
electrolytic zinc coating (ZE)
application of a zinc coating by electrolysis on a suitably prepared steel surface from an aqueous zinc salt solution
by the use of an electric current
NOTE Flat products can have a zinc coating on one or both surfaces. If both surfaces are zinc coated, a different coating
thickness can be applied on each side (this process being referred to as differential zinc coating).
4 Classification and designation
4.1 Classification
The steel grades specified in this standard are classified in accordance with EN 10020 as non-alloy quality steels
(DC01, DC03, DC04, DC05) and alloy quality steel (DC06) and by their increasing suitability for cold forming as
follows:
DC01: drawing quality;
DC03: deep drawing quality;
DC04, DC05: special deep drawing quality
DC06: extra deep drawing quality.
4.2 Designation
4.2.1 The steel names are allocated in accordance with EN 10027-1 and CR 10260; the steel numbers are
allocated in accordance with EN 10027-2.
4.2.2 The products covered by this European Standard shall be designated as follows in the order given:
a) Type of product (e. g. strip, sheet, cut length),
b) Number of this standard (EN 10152),
c) Steel name or steel number and symbol for the type of electrolytical coating (see Table 1),
d) Numbers denoting the nominal coating thickness on each surface (e. g. 50/50 = nominal coating thickness of
5,0 mm on each side, see Table 2 and 6.9.2).
e) Letters A or B indicating the surface quality (see 6.11.2).
f) Letters denoting the surface treatment (see 6.12 and Table 3).
EXAMPLE 1 Designation of strip made of steel DC03+ZE (1.0347+ZE), electrolytically zinc coated with a nominal thickness of
5,0 mm on each surface (50/50), surface quality A, surface treatment phosphated (P):
Strip EN 10152-DC03+ZE50/50-A-P
or
Strip EN 10152-1.0347+ZE50/50-A-P
5
---------------------- Page: 6 ----------------------
EN 10152:2003 (E)
EXAMPLE 2 Designation of sheet made of steel DC05+ZE (1.0312+ZE), electrolytically zinc coated with a nominal thickness
of 7,5 mm on one surface and of 2,5 mm on the other surface (75/25), surface quality B, surface treatment phosphated and oiled
(PO):
Sheet EN 10152-DC05+ZE75/25-B-PO
or
Sheet EN 10152-1.0312+ZE75/25-B-PO
4.2.3 Where appropriate, additional information to the designation as specified in 4.2.2 shall be given to describe
clearly the delivery requirements (see clause 5).
5 Information to be supplied by the purchaser
The following information is required from the purchaser so that the manufacturer may supply the products to
conform with the requirements:
a) complete designation (see 4.2.2);
b) nominal dimensions (thickness, width and, in the case of sheet and cut lengths, length);
c) quantity;
d) limiting mass and sizes of the coils and individual bundles of sheets;
e) properties of steels other than those covered by Table 1 (see 6.1, 6.14.2 and 7.5.3);
f) any requirement concerning a special steelmaking or manufacturing process (see 6.2);
g) any products suitable for making a particular part (see 6.6);
h) any requirement relating to coating on one surface only (see 6.9.5);
i) any requirement for a maximum value of the coating mass (see 6.9.6);
j) any requirement concerning surface quality and surface finish (see 6.11);
k) any requirement on surface roughness (see 6.11.3),
l) any requirement concerning surface treatment (see 6.12 and Table 3);
m) any requirement concerning application of a dimensional standard different from EN 10131 (see 6.14.2);
n) if required type of testing and inspection document (see 7.1.1 and 7.7);
o) any marking desired by branding of the product (see 8.2);
p) any requirement for packing (see clause 9).
6 Requirements
6.1 General
The requirements according to 6.2 to 6.5 and 6.13 apply to products made of the steel grades given in
Table 1.
For other steels used as substrate for electrolytically deposited coatings of zinc (see 1.2 and 1.3) the requirements
shall be based on the appropriate quality standard for the non-coated steel product.
6
---------------------- Page: 7 ----------------------
EN 10152:2003 (E)
6.2 Steelmaking and manufacturing processes
Unless otherwise agreed at the time of enquiry and order, the steelmaking and manufacturing processes are left to
the discretion of the manufacturer. The purchaser shall be informed of these processes, if he requires it.
6.3 Deoxidation
The method of deoxidation shall be in accordance with that specified in Table 1.
6.4 Chemical composition
The chemical composition based on ladle analysis shall be as given in Table 1.
6.5 Delivery condition
The steel substrates are normally supplied in the skin-passed condition. By agreement at the time of enquiry and
order non skin-passed products may be supplied.
6.6 Choice of properties
The products covered by this standard shall comply with the requirements of Table 1. By agreement at the time of
enquiry and order they may be delivered as suitable for making a particular part; in this case a maximum
percentage of scrap may be agreed and acceptance on the basis of mechanical properties is not applicable.
6.7 Mechanical properties
6.7.1 The mechanical properties are given in Table 1; they apply only to skin-passed products.
NOTE The properties in Table 1 are those specified for cold rolled non-coated low carbon steel flat products according to
EN 10130 with the exception of the R , A and n values for the grades DC04+ZE, DC05+ZE and DC06+ZE which have been
e 80 90
altered with respect to the influence of the electrolytical treatment on those properties.
The mechanical properties are valid for the period specified in Table 1 from the date on which the products are
made available. The date of availability shall be notified to the purchaser with reasonable prior notice compatible
with the validity of the mechanical properties. Prolonged storage of products of grade DC01+ZE could result in
some change in the mechanical properties leading to a reduction in formability.
6.7.2 The tensile test values apply to transverse samples and relate to the test piece cross-section without zinc
coating.
7
---------------------- Page: 8 ----------------------
EN 10152:2003 (E)
a
Table 1 - Chemical composition and mechanical properties of electrolytically zinc coated mild steel flat products
Designation Definition and Desoxidation Validity of Surface Absence of R R A r n Chemical composition
e m 80 90 90
Steel grade classification mechanical appea- stretcher % (ladle analysis)
according to properties rance strain MPa MPa min. min. min. %
EN 10020 marks max.
bcd,ed
Steel name Steel Symbol for the CP S Mn Ti
number type of
electrolytically
coating
f h
DC01 1.0330 +ZE Non alloy Manufacturer´s -A - 140 to 280 270 to 28 - - 0,12 0,045 0,045 0,60
g
quality steel discretion B 3 months 410
DC03 1.0347 +ZE Non alloy Fully killed 6 months A 6 months 140 to 240 270 to 34 1,3 - 0,10 0,035 0
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.