EN 10152:2009/AC:2011

Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions

This European Standard specifies requirements for continuously electrolytic zinc coated cold rolled flat products of low carbon steels suitable for cold forming according to Table 1 in rolled widths ≥ 600 mm and thicknesses from 0,35 mm up to and including 3 mm, delivered as strip (in coil form), sheet, slit strip or cut lengths obtained from slit strip or sheet. NOTE 1 This European Standard can also be applied to continuously electrolytic zinc coated flat products of:
a) steels according to EN 10139 (cold rolled strip in rolled widths < 600 mm),
b) steels normally characterized by minimum yield strength or minimum tensile strength values in addition to formability parameters, e. g.
1) steels with high yield strength and improved formability according to EN 10268 (cold rolled flat products),
2) multiphase steels (cold rolled or hot rolled) according to prEN 10338,
3) steels for construction according to national or regional standards (see e. g. DIN 1623).
NOTE 2 By agreement at the time of enquiry and order this European Standard can be applied to continuously electrolytic zinc coated hot-rolled steel flat products (e.g. according to EN 10025-1 and -2, EN 10111, EN 10149-1 to EN 10149-3, etc.). NOTE 3 As the mass of the zinc coating applied is relatively small, the material is not intended to withstand outside exposure without further chemical treatment and painting.

Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen - Technische Lieferbedingungen

Produits plats en acier, laminés à froid, revêtus de zinc par voie électrolytique pour formage à froid - Conditions techniques de livraison

Elektrolizno cinkani hladno valjani ploščati izdelki za hladno preoblikovanje - Tehnični dobavni pogoji

Ta evropski standard določa zahteve za trajno elektrolizno cinkane hladno valjane ploščate izdelke iz maloogljičnega jekla, primerne za hladno preoblikovanje v skladu s preglednico 1, z valjano širino ≥ 600 mm in debelino od 0,35 mm do vključno 3 mm, dobavljene v obliki traka (zvitki), pločevine, razrezanega traka ali narezanih dolžin iz razrezanega traka oziroma pločevine. OPOMBA 1: Ta evropski standard se lahko uporablja za trajno elektrolizno cinkane ploščate izdelke iz:
a) jekla v skladu s standardom EN 10139 (hladno valjan trak v valjanih širinah < 600 mm),
b) jekla, ki ga poleg parametrov oblikovalnosti običajno opredeljujejo najmanjše vrednosti  meje tečenja ali natezne trdnosti , npr.
1) jekla z visoko mejo tečenja in izboljšano oblikovalnostjo v skladu s standardom EN 10268 (hladno valjani ploščati izdelki),
2) večfazna jekla (hladno valjana ali vroče valjana) v skladu s standardom prEN 10338,
3) jekla za gradnjo v skladu z nacionalnimi ali regionalnimi standardi (glejte npr. DIN 1623).
OPOMBA 2: Ta evropski standard je mogoče po dogovoru v času povpraševanja in naročila uporabiti za trajno elektrolizno cinkane vroče valjane ploščate izdelke (npr. v skladu s standardi EN 10025-1 in -2, EN 10111, EN 10149-1 do EN 10149-3 itd.). OPOMBA 3: Ker je masa nanesenega cinkovega premaza sorazmerno majhna, material ni namenjen za uporabo na prostem brez dodatne kemične obdelave in barvanja.

General Information

• Status: Withdrawn
• Publication Date: 20-Dec-2011
• Withdrawal Date: 24-Jan-2017
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: ECISS/TC 109 - Coated and uncoated flat products to be used for cold forming
• Drafting Committee: ECISS/TC 109 - Coated and uncoated flat products to be used for cold forming
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 25-Jan-2017
• Ref Project: SIST EN 10152:2009/AC:2012 - Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions

Relations

• Replaced By: EN 10152:2017 - Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
• Effective Date: 01-Feb-2017
• Corrects: EN 10152:2009 - Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
• Effective Date: 08-Jun-2022

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen - Technische LieferbedingungenProduits plats en acier, laminés à froid, revêtus de zinc par voie électrolytique pour formage à froid - Conditions techniques de livraisonElectrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10152:2009/AC:2011SIST EN 10152:2009/AC:2012en,fr01-februar-2012SIST EN 10152:2009/AC:2012SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10152:2009/AC
December 2011
Décembre 2011
Dezember 2011 ICS 77.140.50 English version Version Française Deutsche Fassung
Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
Produits plats en acier, laminés à froid, revêtus de zinc par voie électrolytique pour formage à froid - Conditions techniques de livraison
Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen - Technische Lieferbedingungen This corrige
...