EN 12808-3:2008

Grouts for tiles - Part 3: Determination of flexural and compressive strength

This European Standard applies to all ceramic tile grouts for internal and external tile installations on walls and floors.
This European Standard describes the test method to be used to determine the compressive and flexural strength of ceramic tile grouts.
This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles.
NOTE   Ceramic tile grouts may also be used for other types of tiles (natural and agglomerated stones, etc.), where these do not adversely affect the stones.

Klebstoffe und Fugenmörtel für Fliesen und Platten - Teil 3: Bestimmung der Biege- und Druckfestigkeit

Diese Europäische Norm ist auf sämtliche Fugenmörtel für keramische Fliesen und Platten an Wand und Boden für innen und außen anwendbar.
Diese Europäische Norm beschreibt das Prüfverfahren zur Bestimmung der Druck  und Biegefestigkeit von Fugenmörtel für keramische Fliesen und Platten.
Diese Europäische Norm enthält keine Anforderungen und keine Empfehlungen hinsichtlich der Planung und Verlegung von keramischen Fliesen/Platten.
ANMERKUNG   Fugenmörtel für keramische Fliesen und Platten können auch für andere Arten von Fliesen und Platten verwendet werden (Natur , Betonwerksteine usw.), sofern diese die Steine nicht negativ beeinflussen.

Mortiers de joints pour carrelage - Partie 3: Détermination de la résistance à la flexion et à la compression

La présente Norme européenne s’applique à tous les mortiers utilisés pour le jointoiement de carrelages
céramiques sur les murs et au sol, à l’intérieur et à l’extérieur.
La présente Norme européenne spécifie la méthode d’essai qui doit être utilisée pour déterminer la résistance
à la flexion et à la compression des mortiers pour le jointement de carrelages céramiques.
La présente Norme européenne ne contient pas de spécifications, ni de recommandations pour la conception,
la pose et le jointoiement des carrelages en céramique.
NOTE Les mortiers de joints pour carrelages céramiques peuvent être également utilisés pour d’autres types de
carrelage (pierre naturelle ou agglomérée, etc.) s'ils sont compatibles.

Lepila in fugirne malte za ploščice - 3. del: Ugotavljanje upogibne in tlačne trdnosti

General Information

• Status: Withdrawn
• Publication Date: 21-Oct-2008
• Withdrawal Date: 13-Sep-2022
• ICS: 83.180 - Adhesives
• ICS: 91.100.10 - Cement. Gypsum. Lime. Mortar
• Technical Committee: CEN/TC 67 - Ceramic tiles
• Drafting Committee: CEN/TC 67/WG 3 - Adhesives and grouts for tiles
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 14-Sep-2022
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Ref Project: SIST EN 12808-3:2009 - Grouts for tiles - Part 3: Determination of flexural and compressive strength

Relations

• Replaces: EN 12808-3:2001 - Grouts for tiles - Part 3: Determination of flexural and compressive strength
• Effective Date: 22-Dec-2008
• Replaced By: EN 13888-2:2022 - Grouts for ceramic tiles - Part 2: Test methods
• Effective Date: 21-Sep-2022

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Mörtel und Klebstoffe für Fliesen und Platten — Teil 3: Bestimmung der Biege- und DruckfestigkeitMortiers de joints pour carrelage - Partie 3: Détermination de la résistance à la flexion et à la compressionGrouts for tiles - Part 3: Determination of flexural and compressive strength91.100.23Ceramic tiles91.100.10Cement. Mavec. Apno. MaltaCement. Gypsum. Lime. Mortar83.180LepilaAdhesivesICS:Ta slovenski standard je istoveten z:EN 12808-3:2008SIST EN 12808-3:2009en,fr,de01-marec-2009SIST EN 12808-3:2009SLOVENSKI
STANDARDSIST EN 12808-3:20021DGRPHãþD



SIST EN 12808-3:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12808-3October 2008ICS 83.180; 91.100.10Supersedes EN 12808-3:2001
English VersionGrouts for tiles - Part 3: Determination of flexural andcompressive strengthMortiers de joints pour carrelage - Partie 3: Déterminationde la résistance à la flexion et à la compressionMörtel und Klebstoffe für Fliesen und Platten - Teil 3:Bestimmung der Biege- und DruckfestigkeitThis European Standard was approved by CEN on 29 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12808-3:2008: ESIST EN 12808-3:2009



EN 12808-3:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Sampling.4 4 Test conditions.4 5 Test materials.4 6 Apparatus.4 7 Procedure.5 7.1 Mixing of grouts.5 7.2 Preparation of test specimens.5 7.3 Flexural strength under standard conditions.6 7.4 Compressive strength under standard conditions.6 7.5 Flexural and compressive strength after freeze-thaw cycles.6 8 Evaluation of results.6 8.1 Flexural strength.6 8.2 Compressive strength.7 9 Test report.
...