EN ISO 6224:2011
(Main)Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011)
Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011)
This International Standard specifies the requirements for general-purpose textile-reinforced thermoplastics
water-discharge hoses.
Three types of hose are specified according to their operating duty requirements, i.e. their ambient and water
temperature ranges:
— ambient temperatures: −10 °C to +60 °C;
— water temperature during operation: 0 °C to +60 °C.
NOTE At water temperatures above 23 °C and particularly above 40 °C, the maximum working pressure will be reduced.
These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine
inlets, as fire-fighting hoses, for special agricultural machines or as gardening hoses for the consumer market.
Kunststoffschläuche mit Textileinlage für allgemeine Anwendungen mit Wasser - Anforderungen (ISO 6224:2011)
Diese Internationale Norm legt die Anforderungen an Kunststoffschläuche mit Textileinlage für allgemeine Anwendungen mit Wasser fest.
Drei Arten von Schläuchen sind entsprechend ihrer Eignung für betriebliche Anforderungen beschrieben, wie z. B. für Umgebungs- und Wassertemperaturbereiche von:
Umgebungstemperaturen: 10 °C bis 60 °C;
Betriebstemperaturbereich: 0 °C bis 60 °C.
ANMERKUNG Bei Temperaturen über 23 °C und insbesondere über 40 °C wird der maximale Betriebsdruck reduziert.
Diese Schläuche sind nicht vorgesehen für die Verwendung beim Transport von Trinkwasser, an Wasch-maschineneinlässen, bei der Brandbekämpfung, bei speziellen Landwirtschaftsmaschinen oder als Garten¬schlauch für den privaten Gebrauch.
Tuyaux en matières thermoplastiques à armature textile d'usage général pour l'eau - Spécifications (ISO 6224:2011)
La présente Norme internationale spécifie les exigences relatives aux tuyaux d'usage général, en matières
thermoplastiques à armature textile pour refoulement d'eau.
Trois types de tuyaux sont spécifiés en fonction de leurs conditions de service, c'est-à-dire leurs plages de
températures ambiantes et de températures d'eau:
— températures ambiantes: −10 °C à +60 °C;
— températures d'eau en service: 0 °C à +60 °C.
NOTE Pour des températures d'eau supérieures à 23 °C et particulièrement supérieures à 40 °C, la pression
maximale de service sera réduite.
Ces tuyaux ne sont pas destinés à être utilisés pour le transport d'eau potable, le raccordement de machine à
laver, comme tuyaux d'incendie, pour les machines agricoles spéciales ou comme tuyaux d'arrosage pour le
marché grand public.
S tekstilom ojačene plastomerne cevi za splošno uporabo vode - Specifikacija (ISO 6224:2011)
Ta mednarodni standard določa zahteve za s tekstilom ojačene plastomerne cevi za splošno uporabo odvajanja vode.
Določene so tri vrste cevi glede na njihove zahteve za delovanje, tj. razpone temperature okolja in vode:
- okoljske temperature: -10 °C do +60 °C,
— temperatura vode med obratovanjem: 0 °C do +60 °C.
OPOMBA: Pri temperaturah vode nad 23 °C in še zlasti nad 40 °C se maksimalni delovni tlak zniža.
Te cevi niso namenjene uporabi za prenos pitne vode, za dotoke v pralne stroje, kot požarne cevi, za posebne kmetijske stroje ali kot vrtne cevi za potrošniški trg.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6224:2011
01-december-2011
1DGRPHãþD
SIST EN ISO 6224:2009
6WHNVWLORPRMDþHQHSODVWRPHUQHFHYL]DVSORãQRXSRUDERYRGH6SHFLILNDFLMD ,62
Thermoplastics hoses, textile-reinforced, for general-purpose water applications -
Specification (ISO 6224:2011)
Einführendes Element - Haupt-Element - Ergänzendes Element (ISO 6224:2011)
Tuyaux en matières thermoplastiques à armature textile d'usage général pour l'eau -
Spécifications (ISO 6224:2011)
Ta slovenski standard je istoveten z: EN ISO 6224:2011
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 6224:2011 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6224:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 6224:2011
EUROPEAN STANDARD
EN ISO 6224
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2011
ICS 23.040.70 Supersedes EN ISO 6224:2008
English Version
Thermoplastics hoses, textile-reinforced, for general-purpose
water applications - Specification (ISO 6224:2011)
Tuyaux en matières thermoplastiques à armature textile Kunststoffschläuche mit Textileinlage für allgemeine
d'usage général pour l'eau - Spécifications (ISO 6224:2011) Anwendungen mit Wasser - Anforderung (ISO 6224:2011)
This European Standard was approved by CEN on 30 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6224:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 6224:2011
EN ISO 6224:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 6224:2011
EN ISO 6224:2011 (E)
Foreword
This document (EN ISO 6224:2011) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and
hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the
latest by April 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6224:2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 6224:2011 has been approved by CEN as a EN ISO 6224:2011 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 6224:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 6224:2011
INTERNATIONAL ISO
STANDARD 6224
Fourth edition
2011-10-01
Thermoplastics hoses, textile-reinforced,
for general-purpose water applications —
Specification
Tuyaux en matières thermoplastiques à armature textile d’usage
général pour l’eau — Spé
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.