EN ISO 16119-2:2013

Agricultural and forestry machinery - Environmental requirements for sprayers - Part 2: Horizontal boom sprayers (ISO 16119-2:2013, Corrected version 2017-03)

ISO 16119-2:2013 specifies requirements and the means for their verification for the design and performance of horizontal boom sprayers, as defined in 3.1, with regard to minimizing the potential risk of environmental contamination during use, including misuse foreseeable by the manufacturer.
It is intended to be used with ISO 16119-1, which gives general requirements common to all the sprayer types covered by ISO 16119. It does not cover safety aspects (see ISO 4254-6).
ISO 16119-2:2013 is not applicable to sprayers manufactured before the date of its publication.

Land- und Forstmaschinen - Pflanzenschutzgeräte zum Ausbringen von Pflanzenschutzmitteln und flüssigen Düngemitteln - Umweltschutz - Teil 2: Feldspritzgeräte und vergleichbare Geräte (ISO 16119-2:2013, korrigierte Fassung 2017-03)

Dieser Teil von ISO 16119 legt Anforderungen und Verfahren zur Überprüfung für die Konstruktion und das Leistungsvermögen von Feldspritzgeräten, wie unter 3.1 definiert, hinsichtlich der Minimierung von Risiken von Verunreinigungen der Umwelt während der Verwendung, einschließlich einer vom Hersteller vorhersehbaren Fehlanwendung, fest.
Dieser Teil ist in Verbindung mit der Norm ISO 16119-1 anzuwenden, die allgemeine Anforderungen an alle Bauarten von Pflanzenschutzgeräten, die von ISO 16119 erfasst werden, beschreibt. Wenn dieser Teil von ISO 16119 abweichende Anforderungen im Vergleich zu ISO 16119-1 enthält, haben die Anforderungen dieses Teiles von ISO 16119 Vorrang vor den Anforderungen von ISO 16119-1 bei Geräten, die von dem Geltungsbereich dieses Teiles von ISO 16119 erfasst werden. Dieser Teil enthält keine Sicherheitsanforderungen (siehe ISO 4254-6).
Dieser Teil von ISO 16119 ist nicht auf Pflanzenschutzgeräte anzuwenden, die vor dem Veröffentlichungsdatum hergestellt wurden.

Matériel agricole et forestier - Exigences environnementales pour les pulvérisateurs - Partie 2: Pulvérisateurs à rampe horizontale (ISO 16119-2:2013, Version corrigée 2017-03)

L'ISO 16119-2:2013 spécifie les exigences et les méthodes de vérification correspondantes pour la conception et les performances des pulvérisateurs à rampe horizontale, avec l'objectif de réduire les risques de contamination de l'environnement durant leur utilisation, y compris lors d'une mauvaise utilisation raisonnablement prévisible par le fabricant.
Elle est prévue pour être utilisée conjointement avec l'ISO 16119‑1, qui donne les exigences générales applicables à tous les types de pulvérisateurs couverts par l'ISO 16119. Lorsque les exigences de la présente partie diffèrent de celles énoncées dans l'ISO 16119‑1, les exigences de l'ISO 16119-2:2013 prennent le pas sur celles de l'ISO 16119‑1 pour les machines faisant partie du domaine d'application de l'ISO 16119-2:2013. L'ISO 16119-2:2013 ne couvre pas les aspects de sécurité (voir l'ISO 4254‑6).
L'ISO 16119-2:2013 n'est pas applicable aux pulvérisateurs qui sont fabriqués avant sa date de publication.

Kmetijski in gozdarski stroji - Okoljevarstvene zahteve za škropilnice - 2. del: Škropilnice za poljščine (ISO 16119-2:2013, popravljena različica 2017-03)

Ta del standarda ISO 16119 opredeljuje zahteve in načine za njihovo preverjanje glede projektiranja in lastnosti škropilnic za poljščine, kot je opredeljeno v točki 3.1, pri čemer si je treba prizadevati za čim manjše tveganje okoljskega onesnaženja med uporabo, vključno s predvideno nepravilno uporabo. Standard je treba uporabljati s standardom ISO 16119-1, ki določa splošne zahteve za vse vrste škropilnic, obravnavane v standardu ISO 16119. Ko se zahteve tega dela standarda ISO 16119 razlikujejo od zahtev, navedenih v standardu ISO 16119-1, imajo zahteve tega dela standarda ISO 16119 prednost pred zahtevami standarda ISO 16119-1 za stroje v okviru tega dela standarda ISO 16119. Ne vključuje varnostnih vidikov (glej standard ISO 4254-6). Ta del standarda ISO 16119 se ne uporablja za škropilnice, izdelane pred datumom njegove objave.

General Information

• Status: Published
• Publication Date: 05-Mar-2013
• Withdrawal Date: 29-Sep-2013
• ICS: 65.060.25 - Equipment for storage, preparation and distribution of fertilizers
• ICS: 65.060.40 - Plant care equipment
• Technical Committee: CEN/TC 144 - Tractors and machinery for agriculture and forestry
• Drafting Committee: CEN/TC 144/WG 3 - Mobile machines and trailers
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 06-Mar-2013
• Due Date: 25-Nov-2012
• Completion Date: 06-Mar-2013
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/471 - Mandate addressed to CEN for standardisation in the field of machinery for pesticide application
• Ref Project: SIST EN ISO 16119-2:2013 - Agricultural and forestry machinery - Environmental requirements for sprayers - Part 2: Horizontal boom sprayers (ISO 16119-2:2013, Corrected version 2017-03)

Relations

• Replaces: EN 12761-2:2001 - Agricultural and forestry machinery - Sprayers and liquid fertilizer distributors - Environmental protection - Part 2: Field crop sprayers
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2013
1DGRPHãþD
SIST EN 12761-2:2001
.PHWLMVNLLQJR]GDUVNLVWURML2NROMHYDUVWYHQH]DKWHYH]DãNURSLOQLFHGHO
âNURSLOQLFH]DSROMãþLQH,62
Agricultural and forestry machinery - Environmental requirements for sprayers - Part 2:
Horizontal boom sprayers (ISO 16119-2:2013)
Land- und Forstmaschinen - Pflanzenschutzgeräte zum Ausbringen von
Pflanzenschutzmitteln und flüssigen Düngemitteln - Umweltschutz - Teil 2:
Feldspritzgeräte und vergleichbare Geräte (ISO 16119-2:2013)
Matériel agricole et forestier - Exigences environnementales pour les pulvérisateurs -
Partie 2: Pulvérisateurs à rampe horizontale (ISO 16119-2:2013)
Ta slovenski standard je istoveten z: EN ISO 16119-2:2013
ICS:
13.020.01 Okolje in varstvo okolja na Environment and
splošno environmental protection in
general
65.060.25 2SUHPD]DVNODGLãþHQMH Equipment for storage,
SULSUDYRLQUD]GHOMHYDQMH preparation and distribution
JQRMLY of fertilizers
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 16119-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2013
ICS 65.060.40 Supersedes EN 12761-2:2001
English Version
Agricultural and forestry machinery - Environmental
requirements for sprayers - Part 2: Horizontal boom sprayers
(ISO 16119-2:2013)
Matériel agricole et forestier - Exigences Land- und Forstmaschinen - Pflanzenschutzgeräte zum
environnementales pour les pulvérisateurs - Partie 2: Ausbringen von Pflanzenschutzmitteln und flüssigen
Pulvérisateurs à rampe horizontale (ISO 16119-2:2013) Düngemitteln - Umweltschutz - Teil 2: Feldspritzgeräte und
vergleichbare Geräte (ISO 16119-2:2013)
This European Standard was approved by CEN on 5 January 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16119-2:2013: E
worldwide for CEN national Members.

Contents Page
Foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EC Directive 2009/127/EC amending 2006/42/EC. 4

Foreword
This document (EN ISO 16119-2:2013) has been prepared by Technical Committee CEN/TC 144 “Tractors
and machinery for agriculture and forestry", the secretariat of which is held by AFNOR, in collaboration with
Technical Committee ISO/TC 23 "Tractors and machinery for agriculture and forestry".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2013, and conflicting national standards shall be
withdrawn at the latest by September 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12761-2:2001.
The following major changes were introduced:
 extension of the scope;
 updating of the normative references;
 addition of a Clause "List of significant hazards";
 revision of requirements on control of spray drift and on cleaning;
 addition of a Clause "Verification";
 completion of Clause "Instruction handbook";
 deletion of Annex A "Test method for cleaning plant protection product cans", and deletion of Annex B
"Example of device for cleaning of plant protection product cans" and addition of a reference to
ISO 21278-1;
 inclusion of Annex C "Additional requirements for band sprayers" into the main text of the Standard;
 addition of Annex ZA.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EC Directive 2009/127/EC amending 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2009/127/EC amending 2006/42/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard confers, within the limits of the scope of this standard, a presumption of conformity with the
relevant Essential Requirements of that Directive and associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.
INTERNATIONAL ISO
STANDARD 16119-2
First edition
2013-03-01
Agricultural and forestry
machinery — Environmental
requirements for sprayers —
Part 2:
Horizontal boom sprayers
Matériel agricole et forestier — Exigences environnementales pour les
pulvérisateurs —
Partie 2: Pulvérisateurs à rampe horizontale
Reference number
ISO 16119-2:2013(E)
©
ISO 2013
ISO 16119-2:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 16119-2:2013(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 List of significant hazards . 2
5 Requirements . 3
5.1 General . 3
5.2 Volume/hectare adjustment system . 9
5.3 Distribution and control of spray drift . 9
5.4 Cleaning .10
5.5 Cleaning devices .11
5.6 Additional requirements for band sprayers .11
5.7 Additional requirements for spray guns and lances .12
6 Verification .12
7 Marking .13
8 Instruction handbook .13
Bibliography .14
ISO 16119-2:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16119-2 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 144, Tractors and machinery for agriculture and forestry, in collaboration with SO Technical
Committee TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 6, Equipment
for crop protection, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
ISO 16119 consists of the following parts, under the general title Agricultural and forestry machinery —
Environmental requirements for sprayers:
— Part 1: General
— Part 2: Horizontal boom sprayers
— Part 3: Sprayers for bush and tree crops
— Part 4: Fixed and semi-mobile sprayers
iv © ISO 2013 – All rights reserved

ISO 16119-2:2013(E)
Introduction
The requirements of this part of ISO 16119 are based on the test methods given in ISO 5682-2:1997,
which were primarily developed for hydraulic sprayers. For other types of sprayers, other test methods
and/or test criteria may be needed and may be the subject of future i
...

SLOVENSKI STANDARD
01-maj-2013
Nadomešča:
SIST EN 12761-2:2001
Kmetijski in gozdarski stroji - Okoljevarstvene zahteve za škropilnice - 2. del:
Škropilnice za poljščine (ISO 16119-2:2013, popravljena različica 2017-03)
Agricultural and forestry machinery - Environmental requirements for sprayers - Part 2:
Horizontal boom sprayers (ISO 16119-2:2013, Corrected version 2017-03)
Land- und Forstmaschinen - Pflanzenschutzgeräte zum Ausbringen von
Pflanzenschutzmitteln und flüssigen Düngemitteln - Umweltschutz - Teil 2:
Feldspritzgeräte und vergleichbare Geräte (ISO 16119-2:2013, korrigierte Fassung 2017
-03)
Matériel agricole et forestier - Exigences environnementales pour les pulvérisateurs -
Partie 2: Pulvérisateurs à rampe horizontale (ISO 16119-2:2013, Version corrigée 2017-
03)
Ta slovenski standard je istoveten z: EN ISO 16119-2:2013
ICS:
13.020.01 Okolje in varstvo okolja na Environment and
splošno environmental protection in
general
65.060.25 Oprema za skladiščenje, Equipment for storage,
pripravo in razdeljevanje preparation and distribution
gnojiv of fertilizers
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 16119-2
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2013
EUROPÄISCHE NORM
ICS 65.060.40 Supersedes EN 12761-2:2001
English Version
Agricultural and forestry machinery - Environmental
requirements for sprayers - Part 2: Horizontal boom
sprayers (ISO 16119-2:2013, Corrected version 2017-03)
Matériel agricole et forestier - Exigences Land- und Forstmaschinen - Pflanzenschutzgeräte zum
environnementales pour les pulvérisateurs - Partie 2: Ausbringen von Pflanzenschutzmitteln und flüssigen
Pulvérisateurs à rampe horizontale (ISO 16119- Düngemitteln - Umweltschutz - Teil 2: Feldspritzgeräte
2:2013, Version corrigée 2017-03) und vergleichbare Geräte (ISO 16119-2:2013,
korrigierte Fassung 2017-03)
This European Standard was approved by CEN on 5 January 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16119-2:2013 E
worldwide for CEN national Members.

Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EC Directive 2009/127/EC amending 2006/42/EC .4

Foreword
This document (EN ISO 16119-2:2013) has been prepared by Technical Committee CEN/TC 144 “Tractors
and machinery for agriculture and forestry", the secretariat of which is held by AFNOR, in collaboration with
Technical Committee ISO/TC 23 "Tractors and machinery for agriculture and forestry".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2013, and conflicting national standards shall be
withdrawn at the latest by September 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12761-2:2001.
The following major changes were introduced:
 extension of the scope;
 updating of the normative references;
 addition of a Clause "List of significant hazards";
 revision of requirements on control of spray drift and on cleaning;
 addition of a Clause "Verification";
 completion of Clause "Instruction handbook";
 deletion of Annex A "Test method for cleaning plant protection product cans", and deletion of Annex B
"Example of device for cleaning of plant protection product cans" and addition of a reference to
ISO 21278-1;
 inclusion of Annex C "Additional requirements for band sprayers" into the main text of the Standard;
 addition of Annex ZA.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16119-2:2013, Corrected version 2017-03 has been approved by CEN as EN ISO 16119-
2:2013 without any modification.

Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EC Directive 2009/127/EC amending 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2009/127/EC amending 2006/42/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard confers, within the limits of the scope of this standard, a presumption of conformity with the
relevant Essential Requirements of that Directive and associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.
INTERNATIONAL ISO
STANDARD 16119-2
First edition
2013-03-01
Corrected version
2017-03
Agricultural and forestry
machinery — Environmental
requirements for sprayers —
Part 2:
Horizontal boom sprayers
Matériel agricole et forestier — Exigences environnementales pour les
pulvérisateurs —
Partie 2: Pulvérisateurs à rampe horizontale
Reference number
ISO 16119-2:2013(E)
©
ISO 2013
ISO 16119-2:2013(E)
© ISO 2013, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2013 – All rights reserved

ISO 16119-2:2013(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 List of significant hazards . 2
5 Requirements . 3
5.1 General . 3
5.1.1 Spray tank . 3
5.1.2 Lines (hoses and pipes) . 5
5.1.3 Spray boom . 5
5.1.4 Filter . 7
5.1.5 Nozzles . 7
5.1.6 Measuring systems. 8
5.1.7 Provisions for connecting test equipment . 8
5.2 Volume/hectare adjustment system . 8
5.2.1 General. 8
5.2.2 Measurements . 8
5.3 Distribution and control of spray drift . 9
5.3.1 Distribution . 9
5.3.2 Control of spray drift .10
5.4 Cleaning .10
5.4.1 Water tank .10
5.4.2 Cleaning systems .10
5.5 Cleaning devices .10
5.6 Additional requirements for band sprayers .11
5.6.1 General.11
5.6.2 Nozzles .11
5.6.3 Distribution .11
5.7 Additional requirements for spray guns and lances .11
6 Verification .
...