iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1948-1:1996

(Main)

Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs - Part 1: Sampling

Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs - Part 1: Sampling

This part of the Standard specifies the sampling of PCDDs/PCDFs. It is an integral part of the complete measurement procedure.  The use of the other two parts EN 1948-2:1996 and EN 1948-3:1996 describing extraction and clean-up and identification and quantification, respectively, is necessary for the determination of the PCDDs and PCDFs.

Emissionen aus stationären Quellen - Bestimmung der Massenkonzentrationen von PCDDs/PCDFs - Teil 1: Probenahme

Der vorliegende Teil der Norm legt die Probenahme der PCDD/PCDF fest. Er ist intergraler Bestandteil des vollständigen Messverfahrens. Die Anwendung der anderen beiden Teile EN 1948-2:1996 und EN 1948-3:1996, die die Extraktion und Reinigung bzw. die Indentifizierung und Quantifizierung beschreiben, ist notwendig für die Bestimmung der PCDD und PCDF.

Emissions de sources fixes - Détermination de la concentration massique en PCDDs/PCDFs - Partie 1: Prélèvement

La présente partie de la norme spécifie des procédure de prélèvement des PCDD/ PCDF. Elle est partie intégrante de la procédure complète de mesure. L'utilisa- tion des deux autres parties de la norme EN 1948-2:1996 et EN 1948-3:1996 décrivant d'une part l'extraction et la purification et d'autres part l'identi- fication et la quantification pour la détermination des PCDD et PCDF.

Emisije nepremičnih virov – Določevanje masne koncentracije PCDD/PCDF – 1. del: Vzorčenje

General Information

Status
Withdrawn
Publication Date
27-Dec-1996
Withdrawal Date
14-Mar-2006
ICS
13.040.40 - Stationary source emissions
Technical Committee
CEN/TC 264 - Air quality
Drafting Committee
CEN/TC 264/WG 1 - Dioxins - emissions
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
15-Mar-2006
Completion Date
15-Mar-2006
Directive
89/369/EEC - Prevention of air pollution from new municipal waste incineration plants
89/429/EEC - Reduction of air pollution from existing municipal waste incineration plants
94/67/EC - Incineration of hazardous waste
Mandate
M/BC/CEN/91/12 - Standardization mandate for CEN concerning a standardized measurement method for dioxins and furans emissions in exhausted gas
Ref Project
SIST EN 1948-1:1999 - Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs - Part 1: Sampling

Relations

Replaced By
EN 1948-1:2006 - Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 1: Sampling of PCDDs/PCDFs
Effective Date
22-Dec-2008

Buy Standard

EN 1948-1:1999EN 1948-1:1999
PreviousNext
Standard
EN 1948-1:1999
English language
44 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Emissionen aus stationären Quellen - Bestimmung der Massenkonzentrationen von PCDDs/PCDFs - Teil 1: ProbenahmeEmissions de sources fixes - Détermination de la concentration massique en PCDDs/PCDFs - Partie 1: PrélevementStationary source emissions - Determination of the mass concentration of PCDDs/PCDFs - Part 1: Sampling13.040.40Stationary source emissionsICS:Ta slovenski standard je istoveten z:EN 1948-1:1996SIST EN 1948-1:1999en01-september-1999SIST EN 1948-1:1999SLOVENSKI
STANDARD



SIST EN 1948-1:1999



SIST EN 1948-1:1999



SIST EN 1948-1:1999



SIST EN 1948-1:1999



SIST EN 1948-1:1999



SIST EN 1948-1:1999



SIST EN 1948-1:1999



SIST EN 1948-1:1999



SIST EN 1948-1:1999



SIST EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17255-4:2023(Main)
Stationary source emissions - Data acquisition and handling systems - Part 4: Specification of requirements for the installation and on-going quality assurance and quality control of data acquisition and handling systems
SIST EN 17255-4:2023

This document specifies the requirements for the installation and on-going quality assurance and quality control of data acquisition and handling systems (DAHS). This includes requirements on:
-   installation (Clause 5);
-   quality assurance and quality control during QAL2 (Clause 6);
-   quality assurance and quality control during on-going operation (Clause 7);
-   annual functional test (Clause 8);
-   documentation (Clause 9).
This document supports the requirements of EN 14181 and legislation such as the IED [1], MCPD [2] and E-PRTR [3]. It does not preclude the use of additional features and functions provided the minimum requirements of this document are met and that these features do not adversely affect data quality, clarity or access.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 17911:2023(Main)
Stationary source emissions - Guideline for the elaboration of standardized measurement methods - Recommendations for the structure and content
SIST-TP CEN/TR 17911:2023

This document supports the elaboration of standardized measurement methods for the determination of stationary source emissions by manual or automated measurement methods.
This document describes the basic elements of standardized measurement methods for the determination of stationary source emissions.
This document is supplemented by an electronic template providing a uniform structure and common elements and texts.
NOTE   Detailed information on the electronic template is given in Annex A.
This document is addressed to working groups of CEN/TC 264 dealing with stationary source emissions. It aims at facilitating in the working groups the elaboration and the harmonization of documents produced by CEN/TC 264. Such documents can be European standards (EN), European Technical Specifications (CEN/TS) or European Technical Reports (CEN/TR).

  • Technical report
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14884:2022(Main)
Stationary source emissions - Determination of total mercury - Automated measuring systems
SIST EN 14884:2023

This document specifies requirements for the calibration and validation (QAL2), the ongoing quality assurance during operation (QAL3) and the annual surveillance test (AST) of AMS used for monitoring total mercury emissions from stationary sources to demonstrate compliance with an emission limit value (ELV). This document is derived from EN 14181 and is only applicable in conjunction with EN 14181.
This document is applicable by direct correlation with the standard reference method (SRM) described in EN 13211.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17656:2022(Main)
Stationary source emissions - Requirements on proficiency testing schemes for emission measurements
SIST EN 17656:2023

This document supplements the requirements of EN ISO/IEC 17043 by providing clarification and additional information for proficiency testing schemes for emission measurements. It gives specific requirements for:
—   competence of proficiency testing providers;
—   proficiency testing facility characteristics; and
—   design, operation and evaluation of proficiency testing schemes by means of interlaboratory comparisons.
All these aspects are necessary in order to organize and conduct proficiency testing on emission measurements.
Requirements on the competence of proficiency testing providers cover personnel, organisation, equipment and environment.
Requirements on the proficiency testing facility characteristics cover measurement sections, measurements ports and working area for the participants.
Requirements on the proficiency testing schemes cover:
—   design, including planning, preparations, homogeneity and stability of test atmospheres and statistical design;
—   operation, including handling and instruction of participants;
—   calculation and use of assigned values; and
—   testing results evaluation, including statistical data.
This document supports the application of proficiency testing schemes for checking the performance of testing laboratories in the context of qualification, accreditation and related quality checks in relation to the application of standardized measurement methods such as standard reference methods (SRM) or alternative methods (AM).
This document is applicable in combination with EN ISO/IEC 17043 only.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17628:2022(Main)
Fugitive and diffuse emissions of common concern to industry sectors - Standard method to determine diffuse emissions of volatile organic compounds into the atmosphere
SIST EN 17628:2022

This document specifies the framework for determining emissions to the atmosphere of Volatile Organic Compounds (VOCs). It specifies a system of methods to detect and/or identify and/or quantify VOC emissions from industrial sources. These methods include Optical Gas Imaging (OGI), Differential Absorption Lidar (DIAL), Solar Occultation Flux (SOF), Tracer Correlation (TC), and Reverse Dispersion Modelling (RDM). It specifies the methodologies for carrying out all the above, and also the performance requirements and capabilities of the direct monitoring methods, the requirements for the results and their measurement uncertainties.
This document specifically addresses, but is not restricted to, the petrochemicals, oil refining, and chemical industries receiving, processing, storing, and/or exporting of VOCs, and includes the emissions of VOCs from the natural gas processing/conditioning industry and the storage of natural gas and similar fuels. The methods specified in this document have been validated at onshore facilities.
This document is applicable to diffuse VOC emissions to atmosphere but not to the emissions of VOCs into water and into solid materials such as soils. It is complementary to EN 15446 [9], the standardized method for the detection, localization of sources (individual leaks from equipment and piping), and quantification of fugitive VOC emissions within the scope of a Leak Detection and Repair Programme (LDAR).
This document has been validated for non-methane VOCs, but the methodology is in principle applicable to methane and other gases.
This document specifies methods to determine (detect, identify and/or quantify) VOC emissions during the periods of monitoring. It does not address the extrapolation of emissions to time periods beyond the monitoring period.

  • Standard
    101 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17255-3:2021(Main)
Stationary source emissions - Data acquisition and handling systems - Part 3: Specification of requirements for the performance test of data acquisition and handling systems
SIST EN 17255-3:2022

This document specifies the performance test of data acquisition and handling systems (DAHS). This includes:
-   specification of test procedures;
-   description of laboratory tests;
-   requirements on the testing laboratory.
This document supports the requirements of EN 14181 and legislation such as the IED, MCPD and E-PRTR. It does not preclude the use of additional features and functions provided the minimum requirements of this document are met and that these features do not adversely affect data quality, clarity or access.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16429:2021(Main)
Stationary source emissions - Reference method for the determination of the concentration of gaseous hydrogen chloride (HCl) in waste gases emitted by industrial installations into the atmosphere
SIST EN 16429:2021

This document specifies the standard reference method (SRM) based on an automatic method for determination of the mass concentration of hydrogen chloride (HCl) in ducts and stacks emitting to the atmosphere. It describes the sampling and gas conditioning system.
This document specifies the characteristics to be determined and the performance criteria to be fulfilled by portable automated measuring systems (P-AMS) using the infrared measurement method. It applies for periodic monitoring and for the calibration or control of automated measuring systems (AMS) permanently installed on a stack, for regulatory or other purposes.
The infrared measurement method described in this document can be used as a SRM, provided the expanded uncertainty of the method is less than 20 % relative at the daily Emission Limit Value (ELV), or 1 mg/m3 for ELV below 5 mg/m3, and the criteria associated to performance characteristics described in EN 15267-4 for portable automated measuring systems (P-AMS), are fulfilled.
This document specifies criteria for demonstration of equivalence of an alternative method (AM) to the SRM by application of EN 14793.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17638:2021(Main)
Stationary source emissions - Manual method for the determination of the mass concentration of formaldehyde - Reference method
SIST-TS CEN/TS 17638:2021

This document specifies the reference method for the determination of the concentration of formaldehyde in emissions from stationary sources. Waste gas samples are taken by absorption in water and subsequently analysed by spectrophotometry or HPLC. The method applies to waste gases in which the formaldehyde concentration is 2 mg/m3 to 60 mg/m3, on dry basis, at the reference conditions of 273 K and 101,3 kPa.
The specific components and the requirements for the measuring system are described. A number of performance characteristics with associated minimum performance criteria are specified for the measuring system.

  • Technical specification
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17340:2020(Main)
Stationary source emissions - Determination of mass concentration of fluorinated compounds expressed as HF - Standard reference method
SIST-TS CEN/TS 17340:2020

This European Standard specifies a manual method for the determination of the concentration of fluorinated compounds expressed in HF. Two cases are presented:
- first case: the measurand is the concentration of hydrofluoric acid and gaseous and bound to particulates fluorides,
- second case: the measurand is the concentration of hydrofluoric acid and gaseous fluorides.
Three analytical techniques are proposed: ionometry, spectrophotometry and ion-exchange chromatography.
This European Standard specifies the performance characteristics to be determined and the performance criteria to be fulfilled when it is used as the Standard Reference Method (SRM) for periodic monitoring and for calibration or control of Automated Measuring Systems (AMS) permanently installed on a stack, for regulatory or other purposes.
This document applies to more or less dust-laden flue gases whose HF concentration may vary between 0,1 mg/m3 and 10 mg/m3, at standard conditions of pressure and temperature. The quantification limit of the method is estimated at 0.1 mg/m3 for a sampled volume of 0.1 m3.

  • Technical specification
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    74 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17405:2020(Main)
Stationary source emissions - Determination of the volume concentration of carbon dioxide - Reference method: infrared spectrometry
SIST-TS CEN/TS 17405:2020

This document specifies the reference method (RM) for the measurement of carbon dioxide (CO2) based on the infrared (IR) absorption principle. It includes the sampling and the gas conditioning system, and allows the determination of the CO2 in flue gases emitted to the atmosphere from ducts and stacks. This document specifies the measurement of the total CO2 concentration and does not differentiate between biogenic and fossil derived CO2.
This document specifies the characteristics to be determined and the performance criteria to be fulfilled by portable automated measuring systems (P-AMS) using the IR measurement method. It applies for periodic monitoring and for the calibration or control of automated measuring systems (AMS) permanently installed on a stack, for regulatory or other purposes.

  • Technical specification
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day