Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2009, corrected version 2010-06-01)

ISO 11296-4:2009, in conjunction with ISO 11296-1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials and other process-related plastics components.

Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 4: Vor Ort härtendes Schlauch-Lining (ISO 11296-4:2009)

Dieser Teil der ISO 11296 legt in Verbindung mit ISO 11296-1 die Anforderungen und Prüfverfahren für vor Ort härtende Schlauch-Lining-Rohre und -Formstücke fest, die für die Renovierung erdverlegter druckloser Abwasserkanäle und -leitungen verwendet werden.
Er gilt für die Verwendung verschiedener härtender Harzsysteme (Duroplaste) in Kombination mit kompatiblen faserigen Trägermaterialien und anderen prozessabhängigen Kunststoffelementen (siehe 5.1).

Systèmes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression - Partie 4: Tubage continu par tubes polymérisés sur place (ISO 11296-4:2009, version corrigée 2010-06-01)

L'ISO 11296-4:2009, conjointement à l'ISO 11296-1, spécifie les exigences et les méthodes d'essais relatives aux tubages continus par tubes polymérisés sur place et aux raccords utilisés pour la rénovation des réseaux d'assainissement enterrés sans pression.
Elle couvre l'utilisation de divers systèmes de résine thermodurcissable, en combinaison avec des matrices fibreuses compatibles et autres procédés relatifs aux composants plastiques.

Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 4. del: Oblaganje s cevmi, utrjenimi na mestu vgradnje (ISO 11296-4:2009, popravljena različica 2010-06-01)

Ta del ISO 11296 v povezavi z ISO 11296-1 določa zahteve in preskusne metode za cevi in fitinge, utrjene na mestu vgradnje, namenjene uporabi za obnovo omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka.
Velja za uporabo različnih sistemov termoreaktivnih smol v kombinaciji z združljivimi vlaknastimi nosilnimi materiali in drugimi polimernimi komponentami, povezanimi s postopkom (glej 5.1).

General Information

Status
Withdrawn
Publication Date
26-Apr-2011
Withdrawal Date
13-Feb-2018
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
14-Feb-2018

Relations

Buy Standard

Standard
EN ISO 11296-4:2011
English language
42 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2011
1DGRPHãþD
SIST EN 13566-4:2003
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DREQRYRSRG]HPQLKRPUHåLM]D
RGYRGQMDYDQMHLQNDQDOL]DFLMR]DREUDWRYDQMHEUH]WODND YRGLVSURVWRJODGLQR 
GHO2EODJDQMHVFHYPLXWUMHQLPLQDPHVWXYJUDGQMH ,62
SRSUDYOMHQDUD]OLþLFD
Plastics piping systems for renovation of underground non-pressure drainage and
sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2009,
corrected version 2010-06-01)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen
Entwässerungsnetzen (Freispiegelleitungen) - Teil 4: Vor Ort härtendes Schlauch-Lining
(ISO 11296-4:2009)
Systèmes de canalisations en matières plastiques pour la rénovation des réseaux
d'assainissement gravitaires enterrés - Partie 4: Tubage continu par tubes polymérisés
sur place (ISO 11296-4:2009, version corrigée 2010-06-01)
Ta slovenski standard je istoveten z: EN ISO 11296-4:2011
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11296-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.20; 23.040.45; 93.030; 91.140.80 Supersedes EN 13566-4:2002
English Version
Plastics piping systems for renovation of underground non-
pressure drainage and sewerage networks - Part 4: Lining with
cured-in-place pipes (ISO 11296-4:2009, corrected version
2010-06-01)
Systèmes de canalisations en plastique pour la rénovation Kunststoff-Rohrleitungssysteme für die Renovierung von
des réseaux de branchements et de collecteurs erdverlegten drucklosen Entwässerungsnetzen
d'assainissement enterrés sans pression - Partie 4: Tubage (Freispiegelleitungen) - Teil 4: Vor Ort härtendes Schlauch-
continu par tubes polymérisés sur place (ISO 11296- Lining (ISO 11296-4:2009)
4:2009, version corrigée 2010-06-01)
This European Standard was approved by CEN on 8 April 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11296-4:2011: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
The text of ISO 11296-4:2009 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings
and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 11296-4:2011 by Technical Committee CEN/TC 155 “Plastics piping systems and
ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13566-4:2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11296-4:2009 has been approved by CEN as a EN ISO 11296-4:2011 without any
modification.
INTERNATIONAL ISO
STANDARD 11296-4
First edition
2009-11-01
Corrected version
2010-06-01
Plastics piping systems for renovation
of underground non-pressure drainage
and sewerage networks —
Part 4:
Lining with cured-in-place pipes
Systèmes de canalisations en matières plastiques pour la rénovation
des réseaux d'assainissement gravitaires enterrés —
Partie 4: Tubage continu par tubes polymérisés sur place

Reference number
ISO 11296-4:2009(E)
©
ISO 2009
ISO 11296-4:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved

ISO 11296-4:2009(E)
Contents Page
Foreword .v
Introduction.vi
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
3.1 General terms .2
3.2 Techniques.3
4 Symbols and abbreviated terms .4
4.1 Symbols.4
4.2 Abbreviated terms .5
5 Pipes at the “M” stage .5
5.1 Materials .6
5.2 General characteristics.7
5.3 Material characteristics.7
5.4 Geometric characteristics .8
5.5 Mechanical characteristics.8
5.6 Physical characteristics.8
5.7 Jointing.8
5.8 Marking.8
6 Fittings at the “M” stage.8
6.1 Materials .8
6.2 General characteristics.9
6.3 Material characteristics.9
6.4 Geometric characteristics .9
6.5 Mechanical characteristics.10
6.6 Physical characteristics.10
6.7 Jointing.10
6.8 Marking.10
7 Ancillary components.10
8 Fitness for purpose of the installed lining system at the “I” stage .10
8.1 Materials .10
8.2 General characteristics.10
8.3 Material characteristics.11
8.4 Geometric characteristics .11
8.5 Mechanical characteristics.11
8.6 Physical characteristics.13
8.7 Additional characteristics.13
8.8 Sampling.13
9 Installation practice.14
9.1 Preparatory work .14
9.2 Storage, handling and transport of pipe components .14
9.3 Equipment .14
9.4 Installation.15
9.5 Process-related inspection and testing .16
9.6 Lining termination .16
9.7 Reconnecting to existing manholes and laterals.16
9.8 Final inspection and testing.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.