Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2021)

This document specifies test procedures for the acquisition and presentation of multipoint data on the following mechanical properties of plastics:
—    dynamic modulus;
—    tensile properties at constant test speed;
—    ultimate stress and strain;
—    tensile stress-strain curves;
—    tensile creep;
—    Charpy impact strength;
—    puncture impact behaviour.
The test methods and test conditions apply predominantly to those plastics that can be injection- or compression-moulded or prepared as sheets of specified thickness from which specimens of the appropriate size can be machined.

Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil 1: Mechanische Eigenschaften (ISO 11403-1:2021)

Dieses Dokument legt Prüfverfahren für die Ermittlung und Darstellung von Vielpunkt Kennwerten für die folgenden mechanischen Eigenschaften von Kunststoffen fest:
- dynamischer Modul;
- Zugeigenschaften bei konstanter Prüfgeschwindigkeit;
- Grenzspannung und  dehnung;
- Zugspannungs Dehnungs Diagramme;
- Kriechverhalten unter Zugbeanspruchung;
- Charpy Schlagzähigkeit;
- Durchstoßverhalten.
Die Prüfverfahren und Prüfbedingungen treffen vorwiegend auf solche Kunststoffe zu, die durch Spritzgießen oder Formpressen oder als Platten mit vorgegebener Dicke hergestellt werden können, aus denen sich Probekörper der erforderlichen Größe fertigen lassen.

Plastiques - Acquisition et présentation de données multiples comparables - Partie 1: Propriétés mécaniques (ISO 11403-1:2021)

Le présent document spécifie des modes opératoires d’essai en vue de l’acquisition et de la présentation de données multiples relatives aux propriétés mécaniques suivantes des plastiques :
—    module dynamique ;
—    propriétés en traction avec vitesse d’essai constante ;
—    contrainte et déformation ultimes ;
—    courbes contrainte-déformation en traction ;
—    fluage en traction ;
—    résistance au choc Charpy ;
—    comportement au choc par perforation.
Ces méthodes et conditions d’essai s’appliquent principalement aux plastiques susceptibles d’être moulés par injection ou compression, ou préparés en feuilles avec une épaisseur spécifiée à partir desquelles il est possible d’usiner des éprouvettes de dimensions appropriées.

Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri različnih pogojih - 1. del: Mehanske lastnosti (ISO 11403-1:2021)

General Information

Status
Published
Publication Date
29-Jun-2021
Withdrawal Date
30-Dec-2021
Technical Committee
Drafting Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
30-Jun-2021
Completion Date
30-Jun-2021

Relations

Buy Standard

Standard
EN ISO 11403-1:2021
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 11403-1:2020
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11403-1:2021
01-september-2021
Nadomešča:
SIST EN ISO 11403-1:2014
Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri
različnih pogojih - 1. del: Mehanske lastnosti (ISO 11403-1:2021)
Plastics - Acquisition and presentation of comparable multipoint data - Part 1:
Mechanical properties (ISO 11403-1:2021)
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil
1: Mechanische Eigenschaften (ISO 11403-1:2021)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 1:
Propriétés mécaniques (ISO 11403-1:2021)
Ta slovenski standard je istoveten z: EN ISO 11403-1:2021
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11403-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 11403-1:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 11403-1:2021


EN ISO 11403-1
EUROPEAN STANDARD

NORME EUROPÉENNE

June 2021
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 11403-1:2014
English Version

Plastics - Acquisition and presentation of comparable
multipoint data - Part 1: Mechanical properties (ISO
11403-1:2021)
Plastiques - Acquisition et présentation de données Kunststoffe - Ermittlung und Darstellung von
multiples comparables - Partie 1: Propriétés vergleichbaren Vielpunkt-Kennwerten - Teil 1:
mécaniques (ISO 11403-1:2021) Mechanische Eigenschaften (ISO 11403-1:2021)
This European Standard was approved by CEN on 6 June 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11403-1:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 11403-1:2021
EN ISO 11403-1:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 11403-1:2021
EN ISO 11403-1:2021 (E)
European foreword
This document (EN ISO 11403-1:2021) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2021, and conflicting national standards
shall be withdrawn at the latest by December 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11403-1:2014.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11403-1:2021 has been approved by CEN as EN ISO 11403-1:2021 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 11403-1:2021

---------------------- Page: 6 ----
...

SLOVENSKI STANDARD
oSIST prEN ISO 11403-1:2020
01-september-2020
Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri
različnih pogojih - 1. del: Mehanske lastnosti (ISO/DIS 11403-1:2020)
Plastics - Acquisition and presentation of comparable multipoint data - Part 1:
Mechanical properties (ISO/DIS 11403-1:2020)
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil
1: Mechanische Eigenschaften (ISO/DIS 11403-1:2020)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 1:
Propriétés mécaniques (ISO/DIS 11403-1:2020)
Ta slovenski standard je istoveten z: prEN ISO 11403-1
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO 11403-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 11403-1:2020

---------------------- Page: 2 ----------------------
oSIST prEN ISO 11403-1:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 11403-1
ISO/TC 61/SC 2 Secretariat: KATS
Voting begins on: Voting terminates on:
2020-07-06 2020-09-28
Plastics — Acquisition and presentation of comparable
multipoint data —
Part 1:
Mechanical properties
Plastiques — Acquisition et présentation de données multiples comparables —
Partie 1: Propriétés mécaniques
ICS: 83.080.01
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 11403-1:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020

---------------------- Page: 3 ----------------------
oSIST prEN ISO 11403-1:2020
ISO/DIS 11403-1:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 11403-1:2020
ISO/DIS 11403-1:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Specimen preparation . 2
5 Conditioning . 3
6 Test requirements . 4
6.1 General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.