EN ISO 19065-2:2019

Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19065-2:2019)

This document specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylenediene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials. Requirements for handling the test material and for conditioning both the test material before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize ASA, AEPDS and ACS moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this document, as are the designatory properties specified in ISO 19065-1.
In order to obtain reproducible and comparable test results, it is intended to use the methods of specimen preparation and conditioning, the specimen dimensions and the test procedures specified in this document. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.

Kunststoffe - Acrylnitril-Styrol-Acrylat (ASA)-, Acrylnitril-(Ethylen-Propylen-Dien)-Styrol (AEPDS)- und Acrylnitril-(Chloriertes Polyethylen)-Styrol (ACS)-Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 19065-2:2019)

Dieses Dokument legt die Verfahren zur Herstellung von Probekörpern und die anzuwendenden Prüfverfahren zur Bestimmung der Eigenschaften von Acrylnitril-Styrol-Acrylat (ASA)-, Acrylnitril-(Ethylen-Propylen-Dien)-Styrol (AEPDS)- und Acrylnitril-(Chloriertes Polyethylen)-Styrol (ACS)-Form-massen fest. Anforderungen an die Behandlung des Probenmaterials und für die Konditionierung des Probenmaterials vor der Herstellung der Probekörper sowie der Probekörper vor der Prüfung sind ebenfalls enthalten.
Verfahren und Bedingungen für die Herstellung der Probekörper und Vorschriften für die Bestimmung der Eigen¬schaften der Werkstoffe, aus denen die Probekörper hergestellt werden, sind angegeben. Eigen-schaften und Prüfverfahren, die anwendbar und notwendig sind, um ASA-, AEPDS- und ACS-Formmassen zu charakterisieren, sind aufgelistet.
Die Eigenschaften wurden aus den allgemeinen Prüfverfahren, die in ISO 10350 1 festgelegt sind, ausgewählt. Andere weithin gebräuchliche Prüfverfahren oder solche von besonderer Bedeutung für diese Formmassen, wie die kennzeichnenden Eigenschaften nach ISO 19065 1, sind in dieses Dokument aufgenommen.
Um reproduzierbare und vergleichbare Prüfergebnisse zu erhalten, ist es vorgesehen, dass die in diesem Dokument festgelegten Verfahren der Probekörperherstellung und  konditionierung, die Probe-körpermaße sowie die Prüfverfahren angewendet werden. Die gemessenen Werte werden nicht zwingend mit denen identisch sein, die bei der Anwendung von Probekörpern anderer Abmessungen oder solchen, die mit anderen Verfahren hergestellt wurden, erhalten werden.

Plastiques - Matériaux à base d'acrylonitrile-styrène-acrylate (ASA), d'acrylonitrile-(éthylène-propylène-diène)-styrène (AEPDS) et d'acrylonitrile-(polyéthylène chloré)-styrène (ACS) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 19065-2:2019)

Le présent document spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai qui doivent être utilisées pour la détermination des propriétés des matériaux à base d'acrylonitrile-styrène-acrylate (ASA), d'acrylonitrile-(éthylène-propylène-diène)-styrène (AEPDS) et d'acrylonitrile-(polyéthylène chloré)-styrène (ACS) pour moulage et extrusion. Les exigences relatives à la manipulation du matériau d'essai et au conditionnement du matériau d'essai avant moulage et des éprouvettes avant essai sont indiquées.
Les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesure des propriétés des matériaux à partir desquels les éprouvettes sont obtenues sont donnés. Les propriétés et méthodes d'essai qui sont utiles et nécessaires pour caractériser les matériaux pour moulage et extrusion à base d'ASA, d'AEPDS et d'ACS sont énumérées.
Les propriétés ont été sélectionnées parmi les méthodes d'essai générales de l'ISO 10350-1. D'autres méthodes d'essai largement utilisées ou qui revêtent une importance particulière pour ces matériaux pour moulage et extrusion sont aussi incluses dans le présent document; c'est le cas des propriétés de désignation spécifiées dans l'ISO 19065‑1.
Dans le but d'obtenir des résultats d'essai reproductibles et comparables, il est nécessaire d'utiliser les méthodes de préparation et de conditionnement des éprouvettes, les dimensions d'éprouvette ainsi que les modes opératoires d'essai spécifiés dans le présent document. Les valeurs déterminées ne seront pas nécessairement identiques à celles obtenues en utilisant des éprouvettes de dimensions différentes ou préparées selon des modes opératoires différents.

Polimerni materiali - Materiali na osnovi kopolimerov akrilonitril-stiren-akrilata (ASA), akrilonitril-(etilen-propilen-dien)-stirena (AEPDS) in akrilonitril-(klorirani polietilen)-stirena (ACS) za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 19065-2:2019)

Ta dokument določa metode za pripravo preskušancev in preskusnih metod za uporabo pri ugotavljanju lastnosti materialov na osnovi kopolimerov akrilonitril-stiren-akrilata (ASA), akrilonitril-(etilen-propilen-dien)-
stirena (AEPDS) ter akrilonitril-(klorirani polietilen)-stirena (ACS) za oblikovanje in ekstrudiranje. Podane so zahteve za ravnanje s preskusnim materialom ter obdelavo preskusnega materiala pred oblikovanjem in obdelavo preskušancev pred preskušanjem.
Podani so postopki in pogoji za pripravo preskušancev ter postopki za merjenje lastnosti materialov, iz katerih so izdelani preskušanci. Navedene so lastnosti in preskusne metode, ki so primerne in nujne za opredelitev materialov na osnovi kopolimerov akrilonitril-stiren-akrilata, akrilonitril-(etilen-propilen-dien)-stirena ter akrilonitril-(klorirani polietilen)-stirena za oblikovanje in ekstrudiranje.
Lastnosti so bile izbrane na podlagi splošnih preskusnih metod iz standarda ISO 10350-1. Druge preskusne metode, ki so v splošni uporabi ali so posebej pomembne za te materiale za oblikovanje in ekstrudiranje, so prav tako vključene v ta dokument. Vključene so tudi označevalne lastnosti, določene v standardu ISO 19065-1.
Da se zagotovijo primerljivi in ponovljivi rezultati preskusa, naj se uporabljajo metode priprave in obdelave primerka, mere preskušanca ter preskusni postopki, ki so določeni v
tem dokumentu. Pri tem ni nujno, da bodo ugotovljene vrednosti enake tistim, ki so pridobljene z uporabo preskušancev,
ki imajo drugačne mere ali so pripravljeni z uporabo drugih postopkov.

General Information

• Status: Published
• Publication Date: 26-Mar-2019
• Withdrawal Date: 29-Sep-2019
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 27-Mar-2019
• Completion Date: 27-Mar-2019
• Ref Project: SIST EN ISO 19065-2:2019 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19065-2:2019)

Relations

• Replaces: EN ISO 6402-2:2003 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:2003)
• Effective Date: 03-Apr-2019

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2019
1DGRPHãþD
SIST EN ISO 6402-2:2004
Polimerni materiali - Materiali na osnovi kopolimerov akrilonitril-stiren-akrilata
(ASA), akrilonitril-(etilen-propilen-dien)-stirena (AEPDS) in akrilonitril-(klorirani
polietilen)-stirena (ACS) za oblikovanje in ekstrudiranje - 2. del: Priprava
preskušancev in ugotavljanje lastnosti (ISO 19065-2:2019)
Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-
styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding
and extrusion materials - Part 2: Preparation of test specimens and determination of
properties (ISO 19065-2:2019)
Kunststoffe - Acrylnitril­Styrol­Acrylat (ASA)­, Acrylnitril­(Ethylen­Propylen­Dien)­Styrol
(AEPDS)­ und Acrylnitril-(Chloriertes Polyethylen)-Styrol (ACS)-Formmassen - Teil 2:
Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 19065-2:2019)
Plastiques - Matériaux à base d'acrylonitrile-styrène-acrylate (ASA), d'acrylonitrile-
(éthylène-propylène-diène)-styrène (AEPDS) et d'acrylonitrile-(polyéthylène chloré)-
styrène (ACS) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et
détermination des propriétés (ISO 19065-2:2019)
Ta slovenski standard je istoveten z: EN ISO 19065-2:2019
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19065-2
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2019
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 6402-2:2003
English Version
Plastics - Acrylonitrile-styrene-acrylate (ASA),
acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS)
and acrylonitrile-(chlorinated polyethylene)-styrene (ACS)
moulding and extrusion materials - Part 2: Preparation of
test specimens and determination of properties (ISO
19065-2:2019)
Plastiques - Matériaux à base d'acrylonitrile-styrène- Kunststoffe - Acrylnitril-Styrol-Acrylat (ASA)-,
acrylate (ASA), d'acrylonitrile-(éthylène-propylène- Acrylnitril-(Ethylen-Propylen-Dien)-Styrol (AEPDS)-
diène)-styrène (AEPDS) et d'acrylonitrile- und Acrylnitril-(Chloriertes Polyethylen)-Styrol (ACS)-
(polyéthylène chloré)-styrène (ACS) pour moulage et Formmassen - Teil 2: Herstellung von Probekörpern
extrusion - Partie 2: Préparation des éprouvettes et und Bestimmung von Eigenschaften (ISO 19065-
détermination des propriétés (ISO 19065-2:2019) 2:2019)
This European Standard was approved by CEN on 8 March 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19065-2:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 19065-2:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2019, and conflicting national standards
shall be withdrawn at the latest by September 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6402-2:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19065-2:2019 has been approved by CEN as EN ISO 19065-2:2019 without any
modification.
INTERNATIONAL ISO
STANDARD 19065-2
First edition
2019-03
Plastics — Acrylonitrile-styrene-
acrylate (ASA), acrylonitrile-(ethylene-
propylene-diene)-styrene (AEPDS)
and acrylonitrile-(chlorinated
polyethylene)-styrene (ACS) moulding
and extrusion materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Matériaux à base d'acrylonitrile-styrène-acrylate
(ASA), d'acrylonitrile-(éthylène-propylène-diène)-styrène (AEPDS) et
d'acrylonitrile-(polyéthylène chloré)-styrène (ACS) pour moulage et
extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 19065-2:2019(E)
©
ISO 2019
ISO 19065-2:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 19065-2:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Preparation of test specimens . 3
4.1 General . 3
4.2 Treatment of the material before moulding . 3
4.3 Injection moulding . 3
4.4 Compression moulding . 4
5 Conditioning of test specimens . 4
6 Determination of properties . 4
Annex A (normative) Determination of the bound-acrylonitrile content in the continuous phase .8
ISO 19065-2:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This first edition of ISO 19065-2 cancels and replaces ISO 6402-2:2003, which has been technically
revised mainly to update the normative references in Clause 2:
— ISO 3167 has been replaced by ISO 20753;
— ISO 1183 has been replaced by ISO 1183-1, ISO 1183-2 and ISO 1183-3;
— IEC 60093 has been replaced by IEC 62631-3-1 and IEC 62631-3-2.
A list of all parts in the ISO 19065 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved

ISO 19065-2:2019(E)
Introduction
There are many methods for testing properties of plastics. For some methods, the data obtained by
different standards are not comparable. Even when the same standards have been used, they often allow
the adoption of a wide range of alternative test conditions, and the data obtained are not necessarily
comparable. The purpose of this document is to specify methods and conditions of test to be used
for the acquisition and presentation of data to ensure that valid comparisons between acrylonitrile-
styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-
(chlorinated polyethylene)-styrene (ACS) materials can be made.
.
INTERNATIONAL STANDARD ISO 19065-2:2019(E)
Plastics — Acrylonitrile-styrene-acrylate (ASA),
acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS)
and acrylonitrile-(chlorinated polyethylene)-styrene (ACS)
moulding and extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
This document specifies the methods of preparation of test specimens and the test methods to be
used in determining the properties of acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-
propylenediene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding
and extrusion materials. Requirements for handling the test material and for conditioning both the test
material before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test s
...