EN ISO 5398-4:2007
(Main)Leather - Chemical determination of chromic oxide content - Part 4: Quantification by inductively coupled plasma - optical emission spectrometer (ICP-OES) (ISO 5398-4:2007)
Leather - Chemical determination of chromic oxide content - Part 4: Quantification by inductively coupled plasma - optical emission spectrometer (ICP-OES) (ISO 5398-4:2007)
ISO 5398-4:2007 describes a method for the determination of chromium in aqueous solution obtained from leather. This is an analysis for total chromium in leather; it is not compound specific or specific to its oxidation state.
This method describes the determination of chromium by inductively coupled plasma – optical emission spectrometry and is applicable to leathers which are expected to have chromic oxide contents in excess of 1 mg/kg. Two techniques for the preparation of the solution to be analysed are included. In the case of dispute, the wet oxidation technique is to be used.
Leder - Chemische Bestimmung des Chromoxidgehalts - Teil 4: Bestimmung durch induktiv gekoppeltes Plasma - Optisches Emissionsspektrometer (ICP-OES) (ISO 5398-4:2007)
Dieser Teil der ISO 5398 beschreibt ein Verfahren zur Bestimmung von Chrom in einer aus Leder erhaltenen wässrigen Lösung. Im vorliegenden Fall handelt es sich um eine Analyse des Gesamtchromgehaltes in Leder, die nicht verbindungsspezifisch oder spezifisch für die Oxidationsstufe ist.
Das vorliegende Verfahren beschreibt die Bestimmung von Chrom durch induktiv gekoppeltes Plasma – Optische Emissionsspektrometrie und ist vorgesehen für die Anwendung bei Ledern, bei denen Chromoxidgehalte im Bereich von mehr als 1 mg/kg vermutet werden.
Enthalten sind zwei Verfahren zur Herstellung der zu analysierenden Lösung. Im Streitfall ist das Nassoxidationsverfahren anzuwenden.
Cuir - Dosage chimique de l'oxyde de chrome - Partie 4: Quantification par plasma à couplage inductif - spectromètre d'émission optique (ICP-OES) (ISO 5398-4:2007)
L'ISO 5398-4:2007 spécifie une méthode permettant de doser le chrome dans une solution aqueuse obtenue à partir de cuir. C'est une analyse du chrome total dans le cuir; elle est non spécifique du composé chromé ou de l'état d'oxydation du chrome.
La présente méthode indique comment doser le chrome par plasma à couplage inductif – spectrométrie d'émission optique et elle s'applique aux cuirs susceptibles de contenir de l'oxyde de chrome dans des proportions supérieures à 1 mg/kg. Deux techniques de préparation de la solution à analyser sont décrites. En cas de désaccord, c'est la méthode d'oxydation en milieu humide qui doit être utilisée.
Usnje - Kemijsko določevanje kromovega oksida - 4. del: Kvantitativno določevanje z induktivno plazemsko/optično spektrometrijo (ICP-OES) (ISO 5398-4:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2009
8VQMH.HPLMVNRGRORþHYDQMHNURPRYHJDRNVLGDGHO .YDQWLWDWLYQR
GRORþHYDQMH]LQGXNWLYQRSOD]HPVNRRSWLþQRVSHNWURPHWULMR ,&32(6 ,62
Leather - Chemical determination of chromic oxide content - Part 4: Quantification by
inductively coupled plasma - optical emission spectrometer (ICP-OES) (ISO 5398-
4:2007)
Leder - Chemische Bestimmung des Chromoxidgehaltes - Teil 4: Bestimmung durch
induktiv gekoppeltes Plasma/optisches Spektrometer (ICP-OES) (ISO 5398-4:2007)
Cuir - Dosage de l'oxyde de chrome - Partie 4: Quantification par plasma a couplage
inductif/spectrométrie d'émission optique (ICP-OES) (ISO 5398-4:2007)
Ta slovenski standard je istoveten z: EN ISO 5398-4:2007
ICS:
59.140.30 Usnje in krzno Leather and furs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 5398-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2007
ICS 59.140.30
English Version
Leather - Chemical determination of chromic oxide content - Part
4: Quantification by inductively coupled plasma - optical
emission spectrometer (ICP-OES) (ISO 5398-4:2007)
Cuir - Dosage chimique de l'oxyde de chrome - Partie 4: Leder - Chemische Bestimmung des Chromoxidgehaltes -
Quantification par plasma à couplage inductif - Teil 4: Bestimmung durch induktiv gekoppeltes
spectromètre d'émission optique (ICP-OES) (ISO 5398- Plasma/optisches Spektrometer (ICP-OES) (ISO 5398-
4:2007) 4:2007)
This European Standard was approved by CEN on 28 July 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5398-4:2007: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Foreword
This document (EN ISO 5398-4:2007) has been prepared by Technical Committee CEN/TC 289 "Leather", the
secretariat of which is held by UNI, in collaboration with the International Union of Leather Technologists and
Chemists Societies (IULTCS).
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2008, and conflicting national standards shall be withdrawn
at the latest by February 2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
INTERNATIONAL ISO
STANDARD 5398-4
IULTCS/IUC
8:4
First edition
2007-08-01
Leather — Chemical determination of
chromic oxide content —
Part 4:
Quantification by inductively coupled
plasma – optical emission spectrometer
(ICP-OES)
Cuir — Dosage chimique de l'oxyde de chrome —
Partie 4: Quantification par plasma à couplage inductif – spectromètre
d'émission optique (ICP-OES)
Reference number
ISO 5398-4:2007(E)
IULTCS/IUC 8:4:2007(E)
©
ISO 2007
ISO 5398-4:2007(E)
IULTCS/IUC 8:4:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
ISO 5398-4:2007(E)
IULTCS/IUC 8:4:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Principle.2
5 Sampling and sample preparation.2
6 Reagents.2
6.1 Wet oxidation method .2
6.2 ICP–OES .2
7 Apparatus .2
8 Methods .3
8.1 Preparation of analytical solution.3
8.2 Measurement of the aqueous solution.3
9 Calculation and expression of results.4
10 Test report .5
Annex A (informative) Determination of water and other volatile matter.6
ISO 5398-4:2007(E)
IULTCS/IUC 8:4:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
This part of ISO 5398 was prepared by the Chemical Tests Commission of the International Union of Leather
Technologists and Chemists Societies (IUC Commission, IULTCS) in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 289, Leather, the secretariat of which is
held by UNI, in accordance with the agreement on technical co-operation between ISO and CEN (Vienna
Agreement). It is based on IUC 8 originally published in J. Soc. Leather Trades Chemists 49, p. 17, (1965)
and declared an official method of the IULTCS in 1965.
IULTCS, originally formed in 1897, is a world-wide organization of professional leather societies to further the
advancement of leather science and technology. IULTCS has three Commissions, which are responsible for
establishing international methods for the sampling and testing of leather. ISO recognizes IULTCS as an
international standardizing body for the preparation of test methods for leather.
ISO 5398 consists of the following parts, under the general title Leather — Chemical determination of chromic
oxide content:
⎯ Part 1: Quantification by titration
⎯ Part 2: Quantification by colorimetric determination
⎯ Part 3: Quantification by atomic absorption spectrometry
⎯ Part 4: Quantification by inductively coupled plasma – optical emission spectrometer (ICP-OES)
iv © ISO 2007 – All rights reserved
ISO 5398-4:2007(E)
IULTCS/IUC 8:4:2007(E)
Introduction
ISO 5398 has been split into four parts, each describing methods suitable for the determination of the chromic
oxide content in leather. The different techniques have been described to reflect the variations in industrial
practice compared with the more sensitive analytical equipment available for test laboratories. Variations also
exist in the range of chromic oxide that the methods are deemed suitable to quantify.
ISO 5398-4 describes a technique that is suitable for determining chromium more precisely than those
described in ISO 5398-1 and ISO 5398-2. It requires the use of sophisticated analytical equipment, such as
inductively coupled plasma and atomic absorption spectroscopy.
ISO 5398-4:2007(E)
INTERNATIONAL STANDARD
IULTCS/IUC 8:4:2007(E)
Leather — Chemical determination of chromic oxide content —
Part 4:
Quantification by inductively coupled plasma — optical
emission spectrometer (ICP-OES)
1 Scope
This part of ISO 5398 describes a method for the determination of chromium in aqueous solution obtained
from leather. This is an analysis for total chromium in leather; it is not compound specific or specific to its
oxidation state.
This method describes the determination of chromium by inductively coupled plasma – optical emission
spectrometry and is applicable to leathers which are expected to have chromic oxide contents in excess of
1 mg/kg. Two techniques for the preparation of the solution to be analysed are included. In the case of
dispute, the wet oxidation technique is to be used.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 2418, Leather — Chemical, physical and mechanical and fastness tests — Sampling location
ISO 3696:1987, Water for analytical laboratory use — Specification and test methods
ISO 4044, Leather — Chemical tests — Preparation of chemical test samples
EN 14602, Footwear — Test methods for the assessment of ecological criteria
ISO 4684, Leather — Chemical tests — Determination of volatile matter
ISO 11885, Water quality — Determination of selected elements by inductively coupled plasma optical
emission spectroscopy (ICP-OES)
3 Terms and definitio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.