EN ISO 10364:2018
(Main)Structural adhesives - Determination of the pot life (working life) of multi-component adhesives (ISO 10364:2015)
Structural adhesives - Determination of the pot life (working life) of multi-component adhesives (ISO 10364:2015)
ISO 10364:2015 specifies methods for determining the pot life of multi-part adhesives in order to be able to determine whether the pot life conforms to the minimum specified working life required of an adhesive.
For the purposes of simplification, the term "pot life" is deemed to have the same meaning as "working life" and will be used to represent both throughout this International Standard. Methods described to measure the property provide different answers. So the results shall be specified with respect to the method used.
The test methods described are suitable for assessing all multi?part adhesives, and especially epoxy based and polyurethane based adhesives, but they are not suitable for some acrylic-based adhesives.
NOTE 1 Some of the methods described in this International Standard can also be suitable for determination of working life of one-part adhesives that react to humidity (e.g. PUR prepolymers).
NOTE 2 This International Standard can also be used for assessing non-structural adhesives.
Strukturklebstoffe - Bestimmung der Topfzeit (Verarbeitungszeit) von Mehrkomponentenklebstoffen (ISO 10364:2015)
Adhésifs structuraux - Détermination de la vie en pot (durée d'utilisation) des adhésifs multicomposants (ISO 10364:2015)
ISO 10364:2015 spécifie des méthodes de détermination de la vie en pot des adhésifs multicomposants afin de pouvoir établir si la vie en pot correspond à la durée d'utilisation minimale spécifiée, requise pour un adhésif.
À des fins de simplification, le terme «vie en pot» est considéré comme ayant la même signification que «durée d'utilisation» et sera utilisé pour les deux occurrences terminologiques tout au long de la présente Norme internationale. Les méthodes décrites pour mesurer cette propriété fournissent des résultats divers. Par conséquent, ces derniers doivent être spécifiés par rapport à la méthode utilisée.
Les méthodes d'essai décrites permettent d'évaluer tous les adhésifs multicomposants, et notamment les adhésifs à base d'époxyde et à base de polyuréthanne mais elles ne sont pas appropriées à l'évaluation de certains adhésifs acryliques.
NOTE 1 Parmi les méthodes décrites dans la présente Norme internationale, certaines peuvent également convenir pour déterminer la durée d'utilisation des adhésifs monocomposants qui réagissent à l'humidité (par exemple les prépolymères PUR).
NOTE 2 La présente Norme internationale peut également être utilisée pour évaluer des adhésifs non structuraux.
Konstrukcijska lepila - Ugotavljanje roka uporabnosti večkomponentnih lepil (ISO 10364:2015)
ISO 10364:2015 opisuje metode za določanje življenjske dobe večdelnih lepil z namenom določanja, če se ta ujema z najkrajšo določeno dobo uporabnosti lepila.
Zavoljo poenostavitve ima pojem »življenjska doba« enak pomen kot »doba uporabnosti« in bo v tem mednarodnem standardu uporabljen za oboje. Opisane metode za merjenje lastnosti nudijo različne odgovore. Rezultati bodo zato določeni glede na uporabljeno metodo.
Opisane preskusne metode so primerne za ocenjevanje vseh večdelnih lepil, zlasti tistih, ki temeljijo na epoksi in poliuretanskih lepilih, niso pa primerne za nekatera akrilna lepila.
OPOMBA 1 Nekatere od metod, opisanih v tem mednarodnem standardu, so prav tako lahko primerne za ugotavljanje življenjske dobe enodelnih lepil, ki reagirajo na vlago (npr. PUR prepolimerov).
OPOMBA 2 Ta mednarodni standard se prav tako lahko uporablja za ocenjevanje nekonstrukcijskih lepil.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2018
1DGRPHãþD
SIST EN 14022:2011
.RQVWUXNFLMVNDOHSLOD8JRWDYOMDQMHURNDXSRUDEQRVWLYHþNRPSRQHQWQLKOHSLO ,62
Structural adhesives - Determination of the pot life (working life) of multi-component
adhesives (ISO 10364:2015)
Strukturklebstoffe - Bestimmung der Topfzeit (Verarbeitungszeit) von
Mehrkomponentenklebstoffen (ISO 10364:2015)
Adhésifs structuraux - Détermination de la durée de vie en pot (délai d'utilisation)
d'adhésifs multicomposants (ISO 10364:2015)
Ta slovenski standard je istoveten z: EN ISO 10364:2018
ICS:
83.180 Lepila Adhesives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 10364
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2018
EUROPÄISCHE NORM
ICS 83.180 Supersedes EN 14022:2010
English Version
Structural adhesives - Determination of the pot life
(working life) of multi-component adhesives (ISO
10364:2015)
Adhésifs structuraux - Détermination de la vie en pot Strukturklebstoffe - Bestimmung der Topfzeit
(délai d'utilisation) d'adhésifs multicomposants (ISO (Verarbeitungszeit) von Mehrkomponentenklebstoffen
10364:2015) (ISO 10364:2015)
This European Standard was approved by CEN on 18 April 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10364:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 10364:2015 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 10364:2018 by
Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2018, and conflicting national standards
shall be withdrawn at the latest by September 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14022:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10364:2015 has been approved by CEN as EN ISO 10364:2018 without any modification.
INTERNATIONAL ISO
STANDARD 10364
Third edition
2015-09-15
Structural adhesives — Determination
of the pot life (working life) of multi-
component adhesives
Adhésifs structuraux — Détermination de la durée de vie en pot (délai
d’utilisation) d’adhésifs multicomposants
Reference number
ISO 10364:2015(E)
©
ISO 2015
ISO 10364:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
ISO 10364:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Procedure. 3
6.1 Sampling . 3
6.2 Method 1: Determination from the change in apparent viscosity . 3
6.3 Method 2: Determination from the change in extrusion rate . 4
6.4 Method 3: Determination from the reaction temperature . 5
6.5 Method 4: Determination by means of a drying recorder . 5
7 Expression of results . 6
8 Test report . 6
Bibliography . 8
ISO 10364:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This third edition cancels and replaces the second edition (ISO 10364:2007), which has been
technically revised.
iv © ISO 2015 – All rights reserved
INTERNATIONAL STANDARD ISO 10364:2015(E)
Structural adhesives — Determination of the pot life
(working life) of multi-component adhesives
SAFETY STATEMENT — Persons using this International Standard should be familiar with
normal laboratory practice, if applicable. This International Standard does not purport to
address all of the safety concerns, if any, associated with its use. It is the responsibility of the
user to establish appropriate safety and health practices and to ensure compliance with any
regulatory requirements.
1 Scope
This International Standard specifies methods for determining the pot life of multi-part adhesives in
order to be able to determine whether the pot life conforms to the minimum specified working life
required of an adhesive.
For the purposes of simplification, the term “pot life” is deemed to have the same meaning as “working life”
and will be used to represent both throughout this International Standard. Methods described to measure
the property provide different answers. So the results shall be specified with respect to the method used.
The test methods described are suitable for assessing all multi–part adhesives, and especially epoxy
based and polyurethane based adhesives, but they are not suitable for some acrylic-based adhesives.
NOTE 1 Some of the methods described in this International Standard can also be suitable for determination
of working life of one-part adhesives that react to humidity (e.g. PUR prepolymers).
NOTE 2 This International Standard can also be used for assessing non-structural adhesives.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 472, Plastics — Vocabulary
ISO 2555, Plastics — Resins in the liquid state or as emulsions or dispersions — Determination of apparent
viscosity by the Brookfield Test method
ISO 3219, Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of
viscosity using a rotational viscometer with defined shear rate
ISO 15605, Adhesives — Sampling
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 472 and the following apply.
3.1
pot life
working life
maximum period of time during which a multi-part adhesive can be used after mixing the components
ISO 10364:2015(E)
4 Principle
This International Standard specifies four methods for the determination of the pot life of multi-
part adhesives.
In method 1, the pot life is determined from the increase in viscosity of the adhesive as it reacts. This
method is not suitable for the determination of pot lives that are shorter than 5 min.
In method 2, the pot life is determined from the decrease in the mass of mixed adhesive which is
extruded in unit time under standard conditions. This method is not suitable for the determination of
pot lives that are shorter than 5 min.
In method 3, the pot life is determined as the time taken by the mixed adhesive to reach a defined
temperature, the so-called critical temperature. This method is applicable to all multi-part systems.
In method 4, the working live of low viscose, self-levelling two part adhesives, or one-part mois
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.