EN 2424:2008

Aerospace series - Marking of aerospace products

This standard specifies the rules for the marking of aerospace products.
It is applicable whenever referenced in the definition document of the product.

Luft und Raumfahrt - Kennzeichnung von Luft- und Raumfahrt-Erzeugnissen

Série aérospatiale - Marquage des produits aérospatiaux

Aeronavtika - Označevanje proizvodov v aeronavtiki

General Information

• Status: Published
• Publication Date: 27-May-2008
• Withdrawal Date: 29-Nov-2008
• ICS: 49.025.01 - Materials for aerospace construction in general
• ICS: 49.035 - Components for aerospace construction
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3 - Mechanical
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 28-May-2008
• Completion Date: 28-May-2008
• Ref Project: SIST EN 2424:2008 - Aerospace series - Marking of aerospace products

Relations

• Replaces: EN 2424:1995 - Aerospace series - Marking of aerospace products
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft und Raumfahrt - Kennzeichnung von Luft- und RaumfahrtteilenSérie aérospatiale - Marquage des produits aérospatiauxAerospace series - Marking of aerospace products49.035Sestavni deli za letalsko in vesoljsko gradnjoComponents for aerospace constructionICS:Ta slovenski standard je istoveten z:EN 2424:2008SIST EN 2424:2008en01-september-2008SIST EN 2424:2008SLOVENSKI
STANDARDSIST EN 2424:20011DGRPHãþD



SIST EN 2424:2008



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2424May 2008ICS 49.035Supersedes EN 2424:1995
English VersionAerospace series - Marking of aerospace productsSérie aérospatiale - Marquage des produits aérospatiauxLuft und Raumfahrt - Kennzeichnung von Luft- undRaumfahrtteilenThis European Standard was approved by CEN on 7 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2424:2008: ESIST EN 2424:2008



EN 2424:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Aim.4 4 Marking practice.4
SIST EN 2424:2008



EN 2424:2008 (E) 3 Foreword This document (EN 2424:2008) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2008, and conflicting national standards shall be withdrawn at the latest by November 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 2424:1995. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 2424:2008



EN 2424:2008 (E) 4 1 Scope This standard specifies the rules for the marking of aerospace products. It is applicable whenever referenced in the definition document of the product. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. TR 3198, Aerospace series — Manufacturer's identification monograms for EN aerospace products 1) 3 Aim 3.1 General The marking allows th
...