iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 15792-3:2008

(Main)

Welding consumables - Test methods - Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld (ISO 15792-3:2000 including Cor 1:2006)

Welding consumables - Test methods - Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld (ISO 15792-3:2000 including Cor 1:2006)

This standard specifies the preparation of the test piece and the evaluation of the test results. The purpose of this standard is to test positional capability of covered electrodes and tubular cored electrode. Fillet welds shall be made in horizontal, vertical up, vertical down and overhead position, as applicable.

Schweißzusätze - Prüfverfahren - Teil 3: Prüfung zur Einteilung der Schweißzusätze nach ihrer Eignung für Schweißpositionen und Wurzeleinbrand an Kehlnähten (ISO 15792-3:2000, enthält Cor. 1:2006)

Dieser Teil von ISO 15792 bezieht sich auf die Einteilung von Elektroden und Drähten zum Lichtbogenschweißen
von Kohlenstoff-Mangan-Stählen, niedriglegierten Stählen, nichtrostenden Stählen und Nickellegierungen, soweit
sie in der Einteilungsnorm aufgeführt sind. Er beschreibt die Herstellung des Prüfstücks und die Bewertung der
Prüfergebnisse im Hinblick auf die Übereinstimmung mit den Anforderungen an die Eignung zum Schweißen in
verschiedenen Positionen und an die Wurzelerfassung nach der Einteilungsnorm für Elektrode oder Draht.
Dieser Teil von ISO 15792 legt keine Anforderungen für die Bewertung fest.

Produits consommables pour le soudage - Méthodes d'essai - Partie 3: Évaluation de l'aptitude au soudage en position et de la pénétration en racine des produits consommables pour les soudures d'angle (ISO 15792-3:2000, Cor 1:2006 inclus)

Dodajni materiali za varjenje - Preskusne metode - 3. del: Preskušanje primernosti dodajnih materialov za varjenje v legah in prevaritev korena pri kotnih varih (ISO 15792-3:2000 including Cor 1:2006)

General Information

Status
Withdrawn
Publication Date
06-May-2008
Withdrawal Date
14-May-2011
ICS
25.160.10 - Welding processes
25.160.20 - Welding consumables
Technical Committee
CEN/TC 121 - Welding
Drafting Committee
CEN/TC 121/WG 3 - Welding consumables
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
15-May-2011
Completion Date
15-May-2011
Ref Project
SIST EN ISO 15792-3:2008 - Welding consumables - Test methods - Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld (ISO 15792-3:2000 including Cor 1:2006)

Relations

Replaces
EN 1597-3:1997 - Welding consumables - Test methods - Part 3: Testing of positional capability of welding consumables in a fillet weld
Effective Date
22-Dec-2008
Replaced By
EN ISO 15792-3:2011 - Welding consumables - Test methods - Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld (ISO 15792-3:2011)
Effective Date
21-May-2011

Buy Standard

EN ISO 15792-3:2008EN ISO 15792-3:2008
PreviousNext
Standard
EN ISO 15792-3:2008
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15792-3:2008
01-september-2008
1DGRPHãþD
SIST EN 1597-3:1998
Dodajni materiali za varjenje - Preskusne metode - 3. del: Preskušanje primernosti
dodajnih materialov za varjenje v legah in prevaritev korena pri kotnih varih (ISO
15792-3:2000 including Cor 1:2006)
Welding consumables - Test methods - Part 3: Classification testing of positional
capacity and root penetration of welding consumables in a fillet weld (ISO 15792-3:2000
including Cor 1:2006)
Schweißzusätze - Prüfverfahren - Teil 3: Prüfung zur Einteilung der Schweißzusätze
nach ihrer Eignung für Schweißpositionen und Wurzeleinbrand an Kehlnähten (ISO
15792-3:2000, enthält Cor. 1:2006)
Produits consommables pour le soudage - Méthodes d'essai - Partie 3: Évaluation de
l'aptitude au soudage en position et de la pénétration en racine des produits
consommables pour les soudures d'angle (ISO 15792-3:2000, Cor 1:2006 inclus)
Ta slovenski standard je istoveten z: EN ISO 15792-3:2008
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
SIST EN ISO 15792-3:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15792-3:2008

---------------------- Page: 2 ----------------------

SIST EN ISO 15792-3:2008
EUROPEAN STANDARD
EN ISO 15792-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2008
ICS 25.160.20 Supersedes EN 1597-3:1997
English Version
Welding consumables - Test methods - Part 3: Classification
testing of positional capacity and root penetration of welding
consumables in a fillet weld (ISO 15792-3:2000 including Cor
1:2006)
Produits consommables pour le soudage - Méthodes Schweißzusätze - Prüfverfahren - Teil 3: Prüfung zur
d'essai - Partie 3: Évaluation de l'aptitude au soudage en Einteilung der Schweißzusätze nach ihrer Eignung für
position et de la pénétration en racine des produits Schweißpositionen und Wurzeleinbrand an Kehlnähten
consommables pour les soudures d'angle (ISO 15792- (ISO 15792-3:2000, enthält Cor. 1:2006)
3:2000, Cor 1:2006 inclus)
This European Standard was approved by CEN on 5 April 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15792-3:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15792-3:2008
EN ISO 15792-3:2008 (E)
Contents Page
Foreword.3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 15792-3:2008
EN ISO 15792-3:2008 (E)
Foreword
The text of ISO 15792-3:2000/Cor 1:2006 has been prepared by Technical Committee ISO/TC 44 “Welding
and allied processes” of the International Organization for Standardization (ISO) and has been taken over as
EN ISO 15792-3:2008 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2008, and conflicting national standards shall be withdrawn
at the latest by November 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1597-3:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 14344:2010(Main)
Welding consumables - Procurement of filler materials and fluxes (ISO 14344:2010)
SIST EN ISO 14344:2011

ISO 14344:2010 specifies tools for communication between a purchaser and a supplier of welding consumables within quality systems, such as those based upon ISO 9001.
In production, the components of welding consumables are divided into discrete, predetermined quantities so that satisfactory tests with a sample from that quantity will establish that the entire quantity meets specification requirements. These quantities, known by such terms as heats, lots, blends, batches and mixes, vary in size according to the manufacturer. For identification purposes, each manufacturer assigns a unique designation to each quantity. This designation usually consists of a series of numbers or letters, or combinations thereof, which will enable the manufacturer to determine the date and time (or shift) of manufacture, the type and source of the raw materials used, and the details of the procedures used in producing the welding consumable. This designation stays with the welding consumable and can be used to identify the material later, in those cases in which identification is necessary.
ISO 14344:2010, together with an applicable International Standard or other standard for welding consumables, provides a method for preparing those specific details needed for welding consumable procurement which consist of: a) the welding consumable classification (selected from the applicable International Standard or other standard for welding consumables); b) the lot classification; c) the testing schedule.
Selection of the specific welding consumable classification, lot classification, and testing schedule depends upon the requirements of the application for which the welding consumable is being procured.
ISO 14344:2010 does not apply to non-consumable electrodes or shielding gases.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14344:2010(Main)
Welding consumables - Procurement of filler materials and fluxes (ISO 14344:2010)
SIST EN ISO 14344:2011

ISO 14344:2010 specifies tools for communication between a purchaser and a supplier of welding consumables within quality systems, such as those based upon ISO 9001.
In production, the components of welding consumables are divided into discrete, predetermined quantities so that satisfactory tests with a sample from that quantity will establish that the entire quantity meets specification requirements. These quantities, known by such terms as heats, lots, blends, batches and mixes, vary in size according to the manufacturer. For identification purposes, each manufacturer assigns a unique designation to each quantity. This designation usually consists of a series of numbers or letters, or combinations thereof, which will enable the manufacturer to determine the date and time (or shift) of manufacture, the type and source of the raw materials used, and the details of the procedures used in producing the welding consumable. This designation stays with the welding consumable and can be used to identify the material later, in those cases in which identification is necessary.
ISO 14344:2010, together with an applicable International Standard or other standard for welding consumables, provides a method for preparing those specific details needed for welding consumable procurement which consist of: a) the welding consumable classification (selected from the applicable International Standard or other standard for welding consumables); b) the lot classification; c) the testing schedule.
Selection of the specific welding consumable classification, lot classification, and testing schedule depends upon the requirements of the application for which the welding consumable is being procured.
ISO 14344:2010 does not apply to non-consumable electrodes or shielding gases.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16739-1:2024(Main)
Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries - Part 1: Data schema (ISO 16739-1:2024)
kSIST FprEN ISO 16739-1:2024

This document represents an open international standard for information used in Building Information Modeling (BIM) that is exchanged and shared among software applications used by the various participants in the construction or facility management industry sector. This document includes definitions that cover information required for buildings and infrastructure works over their life cycle. This edition of the document added coverage of information required for infrastructure facilities including bridges, roads, railways, waterways and port facilities.
This document comprises the publication of a data schema, its documentation, the property and quantity set definitions and the mechanism of an exchange file format structure.
Definitions from this document are used to support different recognized work flows in the construction and facility management industry sector, representing information deliveries. Such information deliveries can be described according to ISO 29481.
Different implementation levels of this document can be defined to better support multiple information deliveries, they are referred to as a Model View Definition (MVD). Each MVD identifies which subset of the definitions of this document imposes requirements for implementation in software applications. Conforming software applications need to identify the model view definition they conform to when applying for software certification.
The following are within the scope of this edition of this document:
BIM exchange format definitions that are required during the life cycle phases of buildings and infrastructure:
demonstrating the need;
conception of need;
outline feasibility;
substantive feasibility study and outline financial authority;
outline conceptual design;
full conceptual design;
coordinated design;
procurement and full financial authority;
production information;
construction;
operation and maintenance.
BIM exchange format definitions that are required by the various disciplines involved within the life cycle phases:
architecture and civil engineering design;
service and utilities engineering;
structural engineering;
procurement;
construction planning;
facility and utility management;
project management;
client requirement management;
industry authorities for permits and approval.
BIM exchange format definitions including:
project structure;
physical components;
spatial components;
analysis items;
processes;
resources;
controls;
actors;
context definition.

  • Draft
    406 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17294-1:2024(Main)
Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 1: General requirements (ISO 17294-1:2024)
kSIST FprEN ISO 17294-1:2023

This document specifies the principles of inductively coupled plasma mass spectrometry (ICP-MS) and provides general requirements for the use of this technique to determine elements in water, digests of sludges and sediments (e.g. digests of water as described in ISO 15587-1 or ISO 15587-2). Generally, the measurement is carried out in water, but gases, vapours or fine particulate matter can be introduced too. This document applies to the use of ICP-MS for aqueous solution analysis.
The ultimate determination of the elements is described in a separate International Standard for each series of elements and matrix. The individual clauses of this document refer the user to these guidelines for the basic principles of the method and the configuration of the instrument.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 683-2:2024(Main)
Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties
kSIST FprEN 683-2:2024

This document specifies the mechanical properties of wrought aluminium and wrought aluminium alloy finstock.
The chemical composition limits of these materials are specified in EN 573 3, unless otherwise agreed between supplier and purchaser.
The designations of wrought aluminium and wrought aluminium alloys and the temper designations used in this document are specified in EN 573 3, and the temper designations are defined in EN 515.

  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 81060-2:2019/A2:2024(Amendment)
Non-invasive sphygmomanometers - Part 2: Clinical investigation of intermittent automated measurement type - Amendment 2 (ISO 81060-2:2018/Amd 2:2024)
SIST EN ISO 81060-2:2020/A2:2024
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16783:2024(Main)
Thermal insulation products - Environmental Product Declarations (EPD) - Product Category Rules (PCR) complementary to EN 15804 for factory made and in-situ formed products
kSIST FprEN 16783:2024

This document provides the product category rules (PCR) for Type III environmental declarations (as in EN 15804:2012+A2:20191) for factory made and in situ thermal insulation products.
Complementary to EN 15804:2012+A2:20191, the PCR described in this document:
-   specify the declared unit to be used;
-   define the system boundaries for thermal insulation products;
-   specify/describe the default scenarios and rules for defining scenarios for certain life cycle information modules.
These PCR are intended to be used for cradle to gate, cradle to gate with options or cradle to grave assessment, provided the intention is properly stated in the system boundary description.

  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16021:2024(Main)
Absorbent incontinence products for urine and/or faeces - Basic principles for evaluation of single-use adult products from the perspective of users and caregivers (ISO 16021:2024)
SIST EN ISO 16021:2024

This document provides guidelines and requirements for designing and conducting an evaluation of single-use adult incontinence absorbing products. It provides guidelines and requirements on creating data collection tools. In particular, it provides a framework for eliciting and recording the views of users and their carers on the acceptability of products. In addition, a product diary is described which can help to quantify some parameters of product use, such as wear times, the mass of urine absorbed by the product and the severity of any leakage from it.
This document does not cover direct comparison between products based on statistical parameters, neither does it provide guidelines on measuring the clinical efficacy of products; that is available in ISO 14155.

  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 2620:2024(Main)
Analysis of natural gas - Biomethane - Determination of VOCs by thermal desorption gas chromatography with flame ionization and/or mass spectrometry detectors (ISO 2620:2024)
kSIST FprEN ISO 2620:2024

This document describes a method for sampling and analysis of volatile organic compounds (VOCs), including siloxanes, terpenes, organic sulfur compounds, in natural gas and biomethane matrices, using thermal desorption gas chromatography with flame ionization and/or mass spectrometry detectors (TD-GC-FID/MS).

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day