iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 582:1993

(Main)

Thermal spraying - Determination of tensile adhesive strength

Thermal spraying - Determination of tensile adhesive strength

In the test to determine the tensile strenght of thermally sprayed deposits, the specimen is loaded in tension. The test is conducted to obtain information on the strength of the coating and/or the strength of the bond between the spary deposit and the parent metal.

Thermische Spritzen - Ermittlung der Haftzugfestigkeit

Der Stirnzugversuch dient zur Bestimmung der Haft-Zugfestigkeit thermisch gespritzter Schichten bei Zugbeanspruchung. Die Prüfung gibt Aufschluss über die Schichtfestigkeit und/oder Haftung zwischen Spritzschicht und Grundwerkstoff

Projection thermique - Mesure de l'adhérence par essais de traction

Dans l'essai permettant de déterminer la résistance d'adhérence des revêtements de projection thermique, l'échantillon est sollicité en traction. L'essai vise à obtenir des renseignements sur la résistance du revêtement, sur la résistance de la liaison entre le dépôt projeté ou le substrat ou les deux.

Vroče brizganje - Ugotavljanje adhezijske natezne trdnosti

General Information

Status
Withdrawn
Publication Date
14-Oct-1993
Withdrawal Date
21-Mar-2017
ICS
25.220.20 - Surface treatment
Technical Committee
CEN/TC 240 - Thermal spraying and thermally spraying coatings
Drafting Committee
CEN/TC 240 - Thermal spraying and thermally spraying coatings
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
22-Mar-2017
Ref Project
SIST EN 582:1999 - Thermal spraying - Determination of tensile adhesive strength

Relations

Replaced By
EN ISO 14916:2017 - Thermal spraying - Determination of tensile adhesive strength (ISO 14916:2017)
Effective Date
29-Mar-2017

Buy Standard

EN 582:1999EN 582:1999
PreviousNext
Standard
EN 582:1999
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Thermische Spritzen - Ermittlung der HaftzugfestigkeitProjection thermique - Mesure de l'adhérence par essais de tractionThermal spraying - Determination of tensile adhesive strength25.220.20Površinska obdelavaSurface t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 14919:2023(Main)
Thermal spraying - Wires, rods and cords for flame and arc spraying - Classification and technical supply conditions (ISO 14919:2023)
SIST EN ISO 14919:2024

This document specifies requirements for classification of metal and non-metal wires (solid and cored), rods, cords processed by means of thermal spraying, especially by arc and flame spraying.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14920:2023(Main)
Thermal spraying - Spraying and fusing of self-fluxing alloys (ISO 14920:2023)
SIST EN ISO 14920:2023

This document specifies the procedure for thermal spraying of self-fluxing alloys that are simultaneously or subsequently fused to create a homogeneous, diffusion-bonded coating.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17832:2023(Main)
Thermal spraying - Determination of the feed rate with spray material in powder form in a production environment
SIST EN 17832:2023

This document describes the procedure for the measurement of the feed rate for thermal spraying with spray materials in powder form in a production environment.
The application of this document is essential if information on the feed rate of a spray material in powder form is required when using a thermal spraying method.
It is applicable to any thermal spraying method using spray materials in powder form (see EN ISO 14917) where the technical installation used allows the spray powder to be fed through without an activated spray gun.
The determination of the feed rate is mandatory for the preparation of thermal spray procedure specifications in accordance with EN 17002 and the determination of the deposition efficiency in accordance with EN ISO 17836.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14922:2021(Main)
Thermal spraying - Quality requirements for manufacturers of thermal sprayed coatings (ISO 14922:2021)
SIST EN ISO 14922:2021

This document specifies quality requirements for manufacturers of thermal sprayed coatings to ensure quality assurance for activities in the field of production.
NOTE      It is independent of the availability of a quality management system, e.g. ISO 9001, ISO 14001 and ISO 45001, which concern the concept and organization of the quality management.
This document defines the quality requirements that are of importance for the manufacturing route.
This document is applicable to thermal spraying including all the pre- and post-treatments of the whole coating process for new parts, for repairs and maintenance (e.g. after service) at the workshop or on site.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15339-2:2021(Main)
Thermal spraying - Safety requirements for thermal spraying equipment - Part 2: Gas control units
SIST EN 15339-2:2021

This document specifies safety requirements of machines and equipment for thermal spraying, in this case of gas control units. This document is intended to be used in conjunction with Part 1, which deals with general aspects when designing, manufacturing, and/or putting in service of machines or equipment.
Generally the requirements of EU Directive 2014/34/EU are valid for the use of this document.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12671:2021(Main)
Thermal spraying - Thermally sprayed coatings - Symbolic representation on drawings (ISO 12671:2021)
SIST EN ISO 12671:2021

This document specifies how the symbolic representation of thermally sprayed coatings is indicated on drawings.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17393:2020(Main)
Thermal spraying - Tubular coating tensile test
SIST EN 17393:2020

This document specifies the procedure for the determination of coating strength, and hence of cohesive strength in a tubular coating tensile test.
The test is intended to determine the tensile coating strength parallel to the spray layers (normal to the spray direction) and to identify differences in particle cohesion quality, as caused by defects as internal delamination at cracks or oxides between the spray particles or splats.
The tubular coating tensile test is suitable for sprayed coatings deposited using metallic materials (not carbides and ceramics).
The tubular coating tensile test is not suitable for fused sprayed coatings deposited using self-fluxing alloys.
The test supports quality assurance and is intended to be applied for the purpose of coating optimization by identifying the influences of coating parameters and spray materials on the coatings's quality. Furthermore, the coating in particular for cold sprayed coatings can be compared with the characteristics of similar solid materials and the coating's quality can be assessed.
This test is not recommended for thin coatings (coating thickness < 500 µm), since massive scattering of results is to be expected here. Due to the size of the specimen, it is particularly suitable to apply the tubular coating tensile test for coating processes that use a concentrated spray jet and a highly focused spray spot, as in the case of cold spraying, high velocity flame spraying (HVOF) or plasma spraying. Applying the tubular coating tensile test for coating processes that use a broad spray jet, such as flame spraying and arc spraying, may require special spraying measures, e.g. the use of a template to ensure a nearly vertical impingement angle.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 2063-1:2019(Main)
Thermal spraying - Zinc, aluminium and and their alloys - Part 1: Design considerations and quality requirements for corrosion protection systems (ISO 2063-1:2019)
SIST EN ISO 2063-1:2019

This document specifies requirements for the protection of iron and steel surfaces against corrosion by applying thermal-sprayed metallic coatings of zinc, aluminium or their alloys.
In this document, requirements for the planning of the corrosion protection system and for the constructive design of the component to be protected are specified, where thermal spraying is intended to be the process for the deposition of the metallic corrosion protection.
Some field-related basic terms are defined and instructions for corrosion behaviour of the zinc and aluminium materials under different environment conditions are provided.
Characteristic properties of the coating, e.g. coating thickness, minimum adhesive strength and surface appearance, are specified and test procedures for thermal-sprayed corrosion protection coatings of zinc, aluminium or their alloys are determined.
This document is valid for applying thermal-sprayed zinc and aluminium protection coatings against corrosion in the temperature range between −50 °C to +200 °C, taking into consideration the service conditions of any sealants used. Heat-resistant protective coatings of aluminium are covered by ISO 17834 and are not in the scope of this document.
Other corrosion protection processes, e.g. hot-dip galvanizing (galvanic coating), sherardizing, electroplating or selection and deposition of organic coatings/paints are not in the scope of this document.
Requirements for the manufacturing of thermal-sprayed coatings are specified in ISO 2063-2.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17002:2018(Main)
Thermal spraying - Components with thermally sprayed coatings - Thermal spray procedure specification
SIST EN 17002:2018

The thermal spray procedure specification (TSPS) is a critically important quality assurance document in the production workflow when producing a thermally sprayed coating.
This document defines the minimum requirements to be followed for the content of a thermal spray procedure specification. When using the thermal spray procedure specification, the requirements of the coating specification are intended to be met. To ensure traceability, the thermal spray procedure specification is intended to be documented and component-related.
Tests and test scopes are intended to be defined by the manufacturer of the coating in a separate test plan according to the requirements of the coating specification.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1395-5:2018(Main)
Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 5: Plasma spraying in chambers
SIST EN 1395-5:2018

This European Standard specifies requirements for the acceptance inspection of thermal spraying equipment, in this case the pressurized part only for low pressure and controlled atmosphere plasma spraying, used in spray jobs to produce thermally sprayed coatings of reproducible quality.
This part is intended to be used in conjunction with EN 1395-1, which includes general requirements and explanations of procedures.
The plasma spraying system itself is intended to be acceptance inspected according to EN 1395-4.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day