EN 62841-3-13:2017

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-13: Particular requirements for transportable drills

IEC 62841-3-13:2017 applies to transportable drills, with manually fed axial movement of the spindle, having a maximum chuck capacity of 13 mm. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. Transportable drills are also known as bench drills or drill presses. This part of IEC 62841 does not apply to stationary drilling machines. This part of IEC 62841 does not apply to radial arm drills. This part of IEC 62841 does not apply to magnetic drill stands and drill motors. This Part 3-13 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Key words: Drills, Hand-held tool, Safety

Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 3-13: Besondere Anforderungen für transportable Bohrmaschinen

Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 3-13: Exigences particulières pour les perceuses transportables

IEC 62841-3-13:2017 s'applique aux perceuses transportables sur lesquelles le mouvement axial de l'arbre est commandé manuellement et qui ont une capacité de mandrin maximale de 13 mm. La tension assignée est inférieure à 3 700 W. Les limites d'application de la présente Norme aux outils fonctionnant sur batterie sont indiquées en K.1 et L.1. La présente Norme traite des dangers présentés par les outils, encourus par tous les individus dans l'utilisation normale et dans l'utilisation impropre raisonnablement prévisible de ces outils. Les outils électroportatifs, qui peuvent être montés sur un support de travail pour être utilisés comme outils installés à poste fixe sans aucune modification de l'outil lui-même, sont compris dans le domaine d'application de la présente Norme et la combinaison d'un outil portatif et d'un support est considérée comme un outil portable, donc couvert par la Partie 3 applicable. Les perceuses transportables sont également appelées perceuses d'établi ou foreuses sur colonne. La présente partie de l'IEC 62841 ne s'applique pas aux perceuses fixes. La présente partie de l'IEC 62841 ne s'applique pas aux perceuses à bras radial. La présente partie de l'IEC 62841 ne s'applique pas aux perceuses magnétiques et à leurs moteurs. La présente Partie 3-13 doit être utilisée conjointement avec la première édition de l'IEC 62841-1:2014. L'attention des Comités Nationaux est attirée sur le fait que les fabricants d'appareils et les organismes d'essai peuvent avoir besoin d'une période transitoire après la publication d'une nouvelle publication IEC, ou d'une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication. Mots clés: Perceuses, Outils portables, Sécurité

Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-13. del: Posebne zahteve za prenosne vrtalnike (IEC 62841-3-13:2017)

Ta del standarda IEC 62841 se uporablja za prenosne vrtalnike z ročno podajanim osnim premikanjem vretena in največjo zmogljivostjo vpenjala 13 mm.
OPOMBA 101: Prenosni vrtalniki se imenujejo tudi namizni vrtalniki ali vrtalne stiskalnice.
Ta del standarda IEC 62841 se ne uporablja za nepremične vrtalne stroje.
Ta del standarda IEC 62841 se ne uporablja za radialne vrtalnike.
Ta del standarda IEC 62841 se ne uporablja za magnetna stojala za vrtalnike in motorje vrtalnikov.
OPOMBA 102: Magnetna stojala za vrtalnike in motorje vrtalnikov bodo zajeti v naslednjem delu standarda IEC 62841-3.
OPOMBA 103: V Evropi (EN 62841-3-13) veljajo naslednji pogoji:
Radialni vrtalniki in nepremični vrtalni stroji so zajeti v standardu EN 12717.

General Information

• Status: Published
• Publication Date: 22-Jun-2017
• Withdrawal Date: 12-Mar-2021
• ICS: 25.120.40 - Electrochemical machines
• Technical Committee: CLC/TC 116 - Safety of hand-held motor-operated electric tools
• Drafting Committee: IEC/TC 116 - Safety of hand-held motor-operated electric tools
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 23-Jun-2017
• Completion Date: 23-Jun-2017
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 62841-3-13:2017 - Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-13: Particular requirements for transportable drills (IEC 62841-3-13:2017)

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2017
(OHNWURPRWRUQDURþQDRURGMDSUHQRVQDRURGMDWHUVWURML]DWUDWRLQYUW9DUQRVW
GHO3RVHEQH]DKWHYH]DSUHQRVQHYUWDOQLNH,(&
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 3-13: Particular requirements for transportable drills (IEC
62841-3-13:2017)
Ta slovenski standard je istoveten z: EN 62841-3-13:2017
ICS:
25.080.40 Vrtalniki Drilling machines
25.140.20 (OHNWULþQDRURGMD Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 62841-3-13

NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2017
ICS 25.120.40
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-13: Particular
requirements for transportable drills
(IEC 62841-3-13:2017 , modified)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-13: Exigences transportable Werkzeuge und Rasen- und
particulières pour les perceuses transportables Gartenmaschinen - Sicherheit - Teil 3-13: Besondere
(IEC 62841-3-13:2017 , modifiée) Anforderungen für transportable Bohrmaschinen
(IEC 62841-3-13:2017 , modifiziert)
This European Standard was approved by CENELEC on 2017-03-13. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-3-13:2017 E
European foreword
The text of document 116/309/FDIS, future edition 1 of IEC 62841-3-13, prepared by IEC/TC 116
"Safety of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN 62841-3-13:2017.
A draft amendment, which covers common modifications to IEC 62841-3-13 (116/309/FDIS), was
prepared by CLC/TC 116 "Safety of motor-operated electric tools" and approved by CENELEC.
The following dates are fixed:
• latest date by which the document has to be implemented at (dop) 2018-03-13
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2021-03-13
the document have to be withdrawn

This European Standard is divided into four parts:
Part 1: General requirements which are common to most hand-held electric motor operated
tools (for the purpose of this standard referred to simply as tools) which could come
within the scope of this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics
of these specific tools.
This Part 3-13 is to be used in conjunction with EN 62841-1:2015.
This Part 3-13 supplements or modifies the corresponding clauses in EN 62841-1:2015, so as to
convert it into the European Standard: Particular requirements for transportable drills.
Where a particular subclause of Part 1 is not mentioned in this Part 3-13, that subclause applies as far
as relevant. When this standard states "addition", "modification" or "replacement", the relevant text in
Part 1 is to be adapted accordingly.
The following print types are used:
- requirements; in roman type
- test specifications: in italic type;
- notes: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting
from 101.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62841-3-13:2017 are prefixed “Z”.
This European Standard follows the overall requirements of EN ISO 12100.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s), see informative Annex ZZ, which is an integral part of this
document.
Compliance with the clauses of Part 1 together with this Part 3-13 provides one means of conforming
with the essential health and safety requirements of the Directive concerned.
Endorsement notice
The text of the International Standard IEC 62841-3-13:2017 was approved by CENELEC as a
European Standard with agreed common modifications.
COMMON MODIFICATIONS
1 Scope
Replace Note 103 with the following:
NOTE 103 Radial arm drills and stationary drilling machines are covered by EN 12717.
8 Marking and instructions
Add the following after 8.14.2 b):
8.14.2 Za) Replacement of items 3, 4 and 5 with the following:
3) The following information:
− that the declared noise emission value(s) have been measured in accordance with a
standard test method and may be used for comparing one tool with another;
− that the declared noise emission value(s) may also be used in a preliminary assessment
of exposure.
4) A warning:
− that the noise emissions during actual use of the power tool can differ from the declared
values depending on the ways in which the tool is used especially what kind of
workpiece is processed; and
− of the need to identify safety measures to protect the operator that are based on an
estimation of exposure in the actual conditions of use.
18 Abnormal operation
Replace the existing Subclause 18.8 with the following:
18.8 Replacement of Table 4 by the following:
Table 4 – Required performance levels
Type and purpose of SCF Minimum Performance
Level (PL)
Power switch - prevent unwanted switch-on b
Power switch - provide desired switch-off b
Any electronic control to pass the test of 18.3 a
Prevent output speed from exceeding 130 % of rated no-load speed a
without accessories mounted
Provide desired direction of rotation Not an SCF
Prevent exceeding thermal limits as in Clause 18 a
Prevent self-resetting as required in 23.3 b
Provide run-down time as required by 19.103 a
Stopping as required by 19.104 a
Restart prevention as required by 19.104 b
Restart prevention as required by 21.18.2.1 a

21 Construction
Replace the existing Subclause 21.18.2.1 with the following:
21.18.2.1 Addition:
The tool shall not restart after an interruption of the mains supply without releasing and re-actuating
the power switch.
Annex I
Replace the title of Annex I with the following:
Annex I
(normative)
Measurement of noise and vibration emissions

and delete the note.
Add the following annex:
Annex ZZ
(informative)
Relationship between this European Standard and the essential requirements
of Directive 2006/42/EC [2006 OJ L157] aimed to be covered
This European Standard has been prepared under a Commission’s standardisation request M/396 to
provide one voluntary means of conforming to essential requirements of Directive 2006/42/EC of the
European Parliament and of the Council of 17 May 2006 on machinery, and amending
Directive 95/16/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZZ.1 – Correspondence between this European Standard
and Annex I of Directive 2006/42/EC
Essential Requirements of Clause(s) / sub-clause(s)
Remarks / Notes
Directive 2006/42/EC of this EN
Annex I All clauses All corresponding requirements
are covered by complying with
all clauses.
WARNING 1: Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2: Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
Bibliography
Replace the bibliography with the following:
The bibliography of EN 62841-1:2015 is applicable, except as follows:
Addition:
EN 12717, Safety of machine tools – Drilling machines
IEC 62841-3-13 ®
Edition 1.0 2017-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electric motor-operated hand-held tools, transportable tools and lawn and

garden machinery – Safety –
Part 3-13: Particular requirements for transportable drills

Outils électroportatifs à moteur, outils portables et machines pour jardins et

pelouses – Sécurité –
Partie 3-13: Exigences particulières pour les perceuses transportables

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.120.40 ISBN 978-2-8322-3889-9

– 2 – IEC 62841-3-13:2017 © IEC 2017
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 6
5 General conditions for the tests . 6
6 Radiation, toxicity and similar hazards . 6
7 Classification . 6
8 Marking and instructions . 6
9 Protection against access to live parts . 7
10 Starting . 8
11 Input and current . 8
12 Heating . 8
13 Resistance to heat and fire . 8
14 Moisture resistance . 8
15 Resistance to rusting . 8
16 Overload protection of transformers and associated circuits . 8
17 Endurance . 8
18 Abnormal operation . 8
19 Mechanical hazards . 9
20 Mechanical strength . 10
21 Construction . 11
22 Inte
...