iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 50321:1999

(Main)

Electrically insulating footwear for working on low voltage installations

Electrically insulating footwear for working on low voltage installations

This standard is applicable to electrically insulating footwear used for working live or close to live parts on installations not exceeding 1 000 V a.c. This footwear, when used in conjunction with other electrically insulating protective equipment such as gloves or blankets, prevents dangerous current from passing through persons via their feet. This standard applies to designs A low shoe, B ankle boot, C half-knee boot, and D knee-height boot, as shown in EN 344. Antistatic and conductive footwear are excluded from the scope of this standard. NOTE: Extension of this standard to overshoes is under consideration. Electrical requirements of this standard may be applied to overshoes but further considerations must be given to non-electrical requirements

Elektrisch isolierende Schuhe zum Arbeiten in Niederspannungsanlagen

Chaussures électriquement isolantes pour travaux sur installations à basse tension

Elektroizolacijska obutev za delo na nizkonapetostnih električnih inštalacijah

General Information

Status
Withdrawn
Publication Date
28-Oct-1999
Withdrawal Date
30-Sep-2002
ICS
13.260 - Protection against electric shock. Live working
13.340.50 - Leg and foot protection
Technical Committee
CLC/TC 78 - Equipment and tools for live working
Drafting Committee
IEC/TC 78 - IEC_TC_78
Parallel Committee
IEC/TC 78 - IEC_TC_78
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
12-Jan-2021
Completion Date
12-Jan-2021
Directive
2016/425 - Regulation (EU) 2016/425 of the European Parliament and of the Council of 9 March 2016 on personal protective equipment and repealing Council Directive 89/686/EEC
89/686/EEC - Council Directive 89/686/EEC of 21 December 1989 on the approximation of the laws of the Member States relating to personal protective equipment
Mandate
M/031 - Standardization mandate to CEN/CENELEC concerning standards for Personal Protective Equipment
Ref Project
SIST EN 50321:2000 - Electrically insulating footwear for working on low voltage installations

Relations

Replaced By
EN 50321-1:2018 - Live working - Footwear for electrical protection - Insulating footwear and overboots
Effective Date
28-Jan-2023

Buy Standard

EN 50321:2000EN 50321:2000
PreviousNext
Standard
EN 50321:2000
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2000
(OHNWURL]RODFLMVNDREXWHY]DGHORQDQL]NRQDSHWRVWQLKHOHNWULþQLKLQãWDODFLMDK
Electrically insulating footwear for working on low voltage installations
Elektrisch isolierende Schuhe zum Arbeiten in Niederspannungsanlagen
Chaussures électriquement isolantes pour travaux sur installations à basse tension
Ta slovenski standard je istoveten z: EN 50321:1999
ICS:
13.260 9DUVWYRSUHGHOHNWULþQLP Protection against electric
XGDURP'HORSRGQDSHWRVWMR shock. Live working
13.340.50 Varovanje nog in stopal Leg and foot protection
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN 503
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 50321-1:2018/AC:2018-08(Corrigendum)
Live working - Footwear for electrical protection - Insulating footwear and overboots
SIST EN 50321-1:2018/AC:2018

TC - Update of EN title; Update of reference in clause 4.4.1; Update of cross-referencing.

  • Corrigendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50321-1:2018(Main)
Live working - Footwear for electrical protection - Insulating footwear and overboots
SIST EN 50321-1:2018

This European Standard specifies the requirements and testing for PPE footwear used as electrical insulating footwear and overboots that provide protection of the worker against electric shock and used for working live or close to live parts on installations up to 36 000 V AC or 25 000 V DC. The products designed and manufactured according to this standard contribute to the safety of the users provided they are used by skilled persons, in accordance with safe methods of work and the instructions for use. Antistatic, electrical shock resistant and conductive footwear are not covered by this standard. NOTE Part 2 Electrical Shock Resistant Footwear and Part 3 Conductive Footwear for Live Working are in development.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50321-1:2018/AC:2018-08(Corrigendum)
Live working - Footwear for electrical protection - Insulating footwear and overboots
SIST EN 50321-1:2018/AC:2018

TC - Update of EN title; Update of reference in clause 4.4.1; Update of cross-referencing.

  • Corrigendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50321-1:2018(Main)
Live working - Footwear for electrical protection - Insulating footwear and overboots
SIST EN 50321-1:2018

This European Standard specifies the requirements and testing for PPE footwear used as electrical insulating footwear and overboots that provide protection of the worker against electric shock and used for working live or close to live parts on installations up to 36 000 V AC or 25 000 V DC. The products designed and manufactured according to this standard contribute to the safety of the users provided they are used by skilled persons, in accordance with safe methods of work and the instructions for use. Antistatic, electrical shock resistant and conductive footwear are not covered by this standard. NOTE Part 2 Electrical Shock Resistant Footwear and Part 3 Conductive Footwear for Live Working are in development.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60034-9:2024(Main)
Rotating electrical machines - Part 9: Noise limits
SIST EN IEC 60034-9:2025

IEC 60034-9:2021 specifies test methods for the determination of sound power level of rotating electrical machines and specifies maximum A-weighted sound power levels for factory acceptance testing of network-supplied, rotating electrical machines in accordance with lEC 60034-1, having methods of cooling according to lEC 60034-6 and degrees of protection according to lEC 60034-5, and having the following characteristics: - standard design, either AC or DC, without additional special electrical, mechanical, or acoustical modifications intended to reduce the sound power level - rated output from 1 kW (or kVA) up to and including 5 500 kW (or kVA) - rated speed not greater than 3 750 min–1 This fifth edition cancels and replaces the fourth edition, published in 2003 and its amendment 1, published in 2007. This edition includes the following significant technical changes with respect to the previous edition: a) In Table 2 and Table 3 cooling methods IC01, IC11, IC21 and IC31, IC71, IC81 are now covered. b) This edition adds Table 3 for 60 Hz machines, whereas Table 2, which covers only 50 Hz machines, has no change in levels. c) In Table 3, grade A is added to harmonize the highest levels seen in IEC and NEMA, whereas grade B was added to harmonize the lowest, more restrictive levels seen in IEC and NEMA. d) The clause “Determination of noise increments caused by converter supply” has been shifted to Annex B and renamed “Information on typical noise increments caused by converter supply”.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60034-12:2024(Main)
Rotating electrical machines - Part 12: Starting performance of single-speed three-phase cage induction motors
SIST EN IEC 60034-12:2025

IEC 60034-12:2024 is available as IEC 60034-12:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60034-12:2024 specifies the parameters for eight designs of starting performance of single-speed three-phase 50 Hz or 60 Hz cage induction motors in accordance with IEC 60034‑1 that: - have a rated voltage up to 1 000 V; - are intended for direct-on-line or star-delta starting; - are rated on the basis of duty type S1; - are constructed to any degree of protection as defined in IEC 60034-5 and explosion protection. This document also applies to dual voltage motors provided that the flux saturation level is the same for both voltages. This fourth edition cancels and replaces the third edition published in 2016. Aligned with the requirements for explosion protected motors from TC31 WG27 - new clause on methods for measuring locked-rotor current and torque; - new informative annex on the general current and torque characteristics with locked rotor; - new informative annex on correction of voltage and frequency; - aligned with the requirements for explosion protected motors from TC31 WG27.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60335-2-39:2024(Main)
Household and similar electrical appliances - Safety - Part 2-39: Particular requirements for commercial electric multi-purpose cooking pans
SIST EN IEC 60335-2-39:2025

IEC 60335-2-39:2012 deals with the safety of electrically operated commercial multi-purpose cooking pans not intended for household and similar use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. This standard also deals with pressurized appliances and appliances with pressurized parts. These appliances are used for processing food for commercial consumption, for example in kitchens of restaurants, canteens, hospitals and in commercial enterprises such as bakeries, butcheries, etc. The electrical part of appliances making use of other forms of energy is also within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by these types of appliances. Attention is drawn to the fact that for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary. The principal changes in this edition as compared with the fifth edition of IEC 60335-2-39 are as follows (minor changes are not listed): - addition to definition of portable appliances, atmospheric multi-purpose cooking and rated pressure; - deletion of equipotential symbol 5021 of IEC 60417 covered by Part 1; - addition of instructions for multi-purpose cooking pans; - modification on leakage current permissible for portable class l appliances; - addition to abnormal test requirements; - addition to mechanical hazard test for multi-purpose cooking pans; - addition of construction test for multi-purpose cooking pans; - addition to construction requirements for lids and theirs grips; - addition to construction requirements for positioning of pressure reliefs; - addition to construction's fixed appliances which are moved forward and backward for cleaning purposes.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication. Keywords: Multi-purpose cooking pans.

  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60335-2-40:2024(Main)
Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
SIST EN IEC 60335-2-40:2025

This European Standard deals with the safety of electric heat pumps, sanitary hot water heat pumps and air conditioners, incorporating motor-compressors as well as hydronic fan coils units, dehumidifiers (with or without motor-compressors), thermoelectric heat pumps and partial units. Their maximum rated voltage being not more than 300 V for single phase appliances and 600 V for multi-phase appliances. Appliances not intended for normal household use but which nevertheless can be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard.

  • Draft
    158 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60335-2-40:2024/A11:2024(Amendment)
Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
SIST EN IEC 60335-2-40:2025/A11:2025

This European Standard deals with the safety of electric heat pumps, sanitary hot water heat pumps and air conditioners, incorporating motor-compressors as well as hydronic fan coils units, dehumidifiers (with or without motor-compressors), thermoelectric heat pumps and partial units. Their maximum rated voltage being not more than 300 V for single phase appliances and 600 V for multi-phase appliances. Appliances not intended for normal household use but which nevertheless can be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard.

  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60034-11:2024(Main)
Rotating electrical machines - Part 11: Thermal protection
SIST EN IEC 60034-11:2025

IEC 60034-11:2020 is available as IEC 60034-11:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60034-11:2020 specifies requirements relating to the use of thermal protectors and thermal detectors incorporated into the stator windings or placed in other suitable positions in induction machines in order to protect them against serious damage due to thermal overloads. It applies to single-speed three-phase 50 Hz or 60 Hz cage induction motors in accordance with IEC 60034-1 and IEC 60034-12 that: - have a rated voltage up to 1 000 V; - are intended for direct-on-line or star-delta starting. The main changes with respect to the previous edition are: - the additional specification of winding temperature limits for temperature class 200 (N), - the increased limits of maximum winding temperatures for overloads with rapid variation, - the clarification that the motor winding may be permanently damaged after it has been exposed to temperatures - a clarification of the definition of indirect thermal protection, - a clarification on the test methods for larger motors.

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day