EN IEC 55016-1-4:2019/A1:2020
(Amendment)Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements
Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements
2018-12-10: WI started as prA1 on 2010 edition and updated to read prA1 on future 2019 edition (IEC ed 4)
Anforderungen an Geräte und Einrichtungen sowie Festlegung der Verfahren zur Messung der hochfrequenten Störaussendung (Funkstörungen) und Störfestigkeit - Teil 1-4: Geräte und Einrichtungen zur Messung der hochfrequenten Störaussendung (Funkstörungen) und Störfestigkeit - Antennen und Messplätze für Messungen der gestrahlten Störaussendung
Spécifications des méthodes et des appareils de mesure des perturbations radioélectriques et de l'immunité aux perturbations radioélectriques - Partie 1-4: Appareils de mesure des perturbations radioélectriques et de l'immunité aux perturbations radioélectriques - Antennes et emplacements d'essai pour les mesures des perturbations rayonnées
Specifikacija merilnih naprav in metod za merjenje radiofrekvenčnih motenj in odpornosti - 1-4. del: Merilne naprave za merjenje radiofrekvenčnih motenj in odpornosti - Antene in preskuševališča za meritve sevanih motenj - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2020
Specifikacija merilnih naprav in metod za merjenje radiofrekvenčnih motenj in
odpornosti - 1-4. del: Merilne naprave za merjenje radiofrekvenčnih motenj in
odpornosti - Antene in preskuševališča za meritve sevanih motenj - Dopolnilo A1
Specification for radio disturbance and immunity measuring apparatus and methods -
Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites
for radiated disturbance measurements
Anforderungen an Geräte und Einrichtungen sowie Festlegung der Verfahren zur
Messung der hochfrequenten Störaussendung (Funkstörungen) und Störfestigkeit – Teil
1-4: Geräte und Einrichtungen zur Messung der hochfrequenten Störaussendung
(Funkstörungen) und Störfestigkeit – Antennen und Messplätze für Messungen der
gestrahlten Störaussendung
Spécifications des méthodes et des appareils de mesure des perturbations
radioélectriques et de l'immunité aux perturbations radioélectriques - Partie 1-4:
Appareils de mesure des perturbations radioélectriques et de l'immunité aux
perturbations radioélectriques - Antennes et emplacements d'essai pour les mesures
des perturbations rayonnées
Ta slovenski standard je istoveten z: EN IEC 55016-1-4:2019/A1:2020
ICS:
17.240 Merjenje sevanja Radiation measurements
33.100.20 Imunost Immunity
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 55016-1-4:2019/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2020
ICS 33.100.10; 33.100.20
English Version
Specification for radio disturbance and immunity measuring
apparatus and methods - Part 1-4: Radio disturbance and
immunity measuring apparatus - Antennas and test sites for
radiated disturbance measurements
(CISPR 16-1-4:2019/A1:2020)
Spécifications des méthodes et des appareils de mesure Anforderungen an Geräte und Einrichtungen sowie
des perturbations radioélectriques et de l'immunité aux Festlegung der Verfahren zur Messung der hochfrequenten
perturbations radioélectriques - Partie 1-4: Appareils de Störaussendung (Funkstörungen) und Störfestigkeit - Teil 1-
mesure des perturbations radioélectriques et de l'immunité 4: Geräte und Einrichtungen zur Messung der
aux perturbations radioélectriques - Antennes et hochfrequenten Störaussendung (Funkstörungen) und
emplacements d'essai pour les mesures des perturbations Störfestigkeit - Antennen und Messplätze für Messungen
rayonnées der gestrahlten Störaussendung
(CISPR 16-1-4:2019/A1:2020) (CISPR 16-1-4:2019/A1:2020)
This amendment A1 modifies the European Standard EN IEC 55016-1-4:2019; it was approved by CENELEC on 2020-07-20. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 55016-1-4:2019/A1:2020 E
European foreword
The text of document CIS/A/1316/FDIS, future CISPR 16-1-4/A1, prepared by CISPR SC A "Radio-
interference measurements and statistical methods" of CISPR "International special committee on
radio interference" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-04-20
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-07-20
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard CISPR 16-1-4:2019/A1:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
CISPR 11 NOTE Harmonized as EN 55011
CISPR 16-1-4 ®
Edition 4.0 2020-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
INT ERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
C OMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES
AMENDMENT 1
AMENDEMENT 1
Specification for radio disturbance and immunity measuring apparatus
and methods –
Part 1-4: Radio disturbance and immunity measuring apparatus – Antennas
and test sites for radiated disturbance measurements
Spécifications des méthodes et des appareils de mesure des perturbations
radioélectriques et de l'immunité aux perturbations radioélectriques –
Partie 1-4: Appareils de mesure des perturbations radioélectriques et de
l'immunité aux perturbations radioélectriques – Antennes et emplacements
d'essai pour les mesures des perturbations rayonnées
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.100.10; 33.100.20 ISBN 978-2-8322-8450-6
– 2 – CISPR 16-1-4:2019/AMD1:2020
© IEC 2020
FOREWORD
This amendment has been prepared by subcommittee CISPR A: Radio-interference
measurements and statistical methods, of IEC technical committee CISPR: International special
committee on radio interference.
The text of this amendment is based on the following documents:
FDIS Report on voting
CIS/A/1316/FDIS CIS/A/1320/RVD
Full information on the voting for the approval of this amendment can be found in the report on
voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC website under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this document using a colour printer.
_____________
3.2 Abbreviated terms
Add the following new abbreviated terms to the existing list:
DRH double ridged horn
XP cross polarization
PDF probability density function
4.5.5 Cross-polar response of antenna
Delete, in the first sentence of the existing last paragraph, the cross-reference to [21].
CISPR 16-1-4:2019/AMD1:2020 – 3 –
© IEC 2020
4.7 Special antenna arrangements – large-loop antenna system
Replace the first sentence of the third paragraph with the following new sentence:
The EUT shall be positioned in the centre of the LLAS on a non-conductive support table.
Replace the third sentence of the third paragraph with the following new sentence:
Guidelines for routing of EUT cables are given in C.3 and Figure C.6.
Add, after the existing third paragraph, the following new paragraph:
The LLAS may be placed in any environment. Placement inside a shielded room, SAC, FAR, or
weather-protected OATS is permitted. Placement in a shielded environment is recommended
to eliminate ambient signals allowing for better sensitivity to EUT emissions. A minimum
distance of 0,5 m between the LLAS and any metallic plane is recommended. The validation of
the LLAS shall be performed at the location where the LLAS measurements normally take place
to take into account the effect of the environment (see C.4).
Replace, in the NOTE, "Correction factors" with "Conversion factors".
C.3 Construction of a large-loop antenna (LLA)
Replace the existing third paragraph with the following paragraph:
The standard diameter of each LLA is defined as D = 2 m (i.e. the reference diameter). If
necessary, e.g. in the case of a large EUT, D may be increased. However, in the frequency
range up to 30 MHz, the maximum diameter allowed is 4 m. Further increase of the diameter
can result in non-reproducible resonances of the LLAS response at the high-frequency end of
the measuring range. The validation method specified in C.4 applies for LLAS loops with
diameters of 2 m, 3 m, or 4 m.
Replace the second sentence of the seventh paragraph "The insertion loss of the current probe
shall be sufficiently low (see NOTE 1)." with "The insertion impedance of the current probe
should be sufficiently low (see NOTE)."
Delete the existing NOTE 1 and NOTE 2.
– 4 – CISPR 16-1-4:2019/AMD1:2020
© IEC 2020
Add, between the seventh and eighth paragraphs, the following new NOTE:
NOTE To obtain a flat frequency response for each LLA at the lower end of the 9 kHz to 30 MHz frequency range,
the resistive part of the insertion impedance, R , of the current probe is designed to be much smaller than 2π f L at
c c
f = 9 kHz, where L represents the inductance of the current probe. In addition, R + R is to be less than or equal to
c c i
X /10 = (2π f L)/10 at 9 kHz, where R is the resistance of the inner conductor of the loop and L is the loop inductance.
i i
This inductance is about 1,5 µH/m along the circumference; thus, for each standard LLA whose diameter is 2 m,
X ≈ 0,5 Ω at f = 9 kHz.
i
Add, at the end of the existing text (before Figure C.1), the following new paragraph:
To avoid unwanted capacitive coupling between the EUT and the LLAS, the distance between
the EUT and components of the LLAS shall be at least 0,10 times the loop diameter. Particular
attention should be paid to the leads of an EUT. Cables shall be routed together and leave the
test volume in the same octant of the LLAS, no closer than 0,4 m to any of the LLAS loops (see
Figure C.6).
C.4 Validation of an LLA
Replace the existing title of this clause with the following new title:
C.4 Validation of the LLAS
Replace the first paragraph of this clause with the following three new paragraphs:
The validation of the LLAS shall be carried out by measuring the current induced in each of the
three LLAs by means of the LLAS verification dipole connected to a 50 Ω RF generator, as
described in C.5. The magnetic field emitted by the dipole allows verification of the magnetic
field sensitivity of the LLAS. The electric field emitted by the LLAS verification dipole is intended
to verify that the electric field sensitivity of the LLAS is sufficiently low.
The validation of an LLAS shall be performed at the site where the LLAS measurements
normally take place. This is to account for the effect of the floor, walls, and similar objects or
surfaces in the specific environment of the LLAS.
Validation measurements shall be performed at least at the following frequencies: 9 kHz,
100 kHz, 1 MHz, 2 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz, 20 MHz, 25 MHz, and 30 MHz.
Replace the existing second and third paragraphs with the following new paragraphs:
The induced current shall be measured as a function of frequency in the range of 9 kHz to
30 MHz at the eight positions of the LLAS verification dipole shown in Figure C.7. During this
measurement, the LLAS verification dipole shall be in the plane of the LLA under test.
In each of the eight positions, the measured validation factor, expressed in dB(Ω) as
20 lg(V /I ), where V is the open circuit voltage of the RF generator and I is the measured
go I go I
current, shall not deviate by more than ±3 dB from the applicable reference validation factor
given in Figure C.8 and Table C.1.
CISPR 16-1-4:2019/AMD1:2020 – 5 –
© IEC 2020
Delete the existing fourth paragraph.
Add, before Figure C.7, three new paragraphs as follows:
The reference validation factors given in Figure C.8 and Table C.1 are valid for an LLAS with
circular loops having diameters of D = 2 m, 3 m, or 4 m.
Tabular values of the curves presented in Figure C.8 are given in Table C.1. These tabular
values shall be used for the LLAS validation.
Background material and the equations for calculating the reference validation factors are given
in CISPR TR 16-3:2020 [23].
Figure C.7 – The eight positions of the LLAS verification dipole during validation of an
LLA
Replace the existing figure with the following new figure:
Figure C.7 – The eight positions of the LLAS verification
dipole during validation of an LLA
– 6 – CISPR 16-1-
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.