EN 55035:2017
(Main)Electromagnetic compatibility of multimedia equipment - Immunity requirements
Electromagnetic compatibility of multimedia equipment - Immunity requirements
CISPR 35:2016 applies to multimedia equipment (MME) having a rated AC or DC supply voltage not exceeding 600 V. The objectives of this document are:
- to establish requirements which provide an adequate level of intrinsic immunity so that the MME will operate as intended in its environment in the frequency range 0 kHz to 400 GHz; and
- to specify procedures to ensure the reproducibility of tests and the repeatability of results.
Elektromagnetische Verträglichkeit von Multimediageräten - Anforderungen zur Störfestigkeit
Compatibilité électromagnétique des équipements multimédia - Exigences d'immunité
Elektromagnetna združljivost večpredstavnostne opreme - Zahteve za odpornost opreme
NAVODILO Modro obarvano besedilo v tem dokumentu označuje besedilo, usklajeno s standardom CISPR 32. Standard CISPR 32 vsebuje
ustrezne zahteve glede emisij nad 150 kHz za opremo znotraj področja uporabe tega dokumenta.
Ta dokument velja za večpredstavnostno opremo (MME), kakor je opredeljeno v 3.1.24, z napajalno napetostjo izmeničnega toka (AC) ali enosmernega toka (DC), ki ne presega 600 V.
Večpredstavnostna oprema znotraj področja uporabe standarda CISPR 20 ali CISPR 24 je znotraj področja uporabe tega dokumenta.
Večpredstavnostna oprema s funkcijo sprejemanja oddajanja je znotraj področja uporabe tega dokumenta, glej dodatek A.
Večpredstavnostna oprema z brezžičnimi vmesniki, ki ne oddajajo, je tudi znotraj področja uporabe tega dokumenta, vendar skladnost s tem dokumentom ne zahteva ocenjevanja delovanja teh vmesnikov.
Večpredstavnostna oprema, ki je namenjena predvsem za profesionalno uporabo, sodi v področje uporabe tega dokumenta.
Večpredstavnostna oprema, za katero so zahteve glede odpornosti v frekvenčnem območju, ki ga zajema ta dokument, izrecno navedene v drugih dokumentih CISPR (razen CISPR 20 in CISPR 24), ni vključena v področje uporabe tega dokumenta.
Namen tega dokumenta je:
• pripraviti zahteve, ki zagotavljajo ustrezno stopnjo intrinzične odpornosti, tako da bo večpredstavnostna oprema delovala, kot je bilo predvideno v svojem okolju v frekvenčnem območju od 0 kHz do 400 GHz; • določiti postopke, s katerimi se zagotovi obnavljanje preskusov in ponovljivost rezultatov. Zaradi tehnološke konvergence funkcij večpredstavnostne opreme so bila merila delovanja določena na funkcionalno usmerjeni podlagi in ne na podlagi, usmerjeni v opremo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2017
(OHNWURPDJQHWQD]GUXåOMLYRVWYHþSUHGVWDYQRVWQHRSUHPH=DKWHYH]DRGSRUQRVW
RSUHPH
Electromagnetic Compatibility of Multimedia equipment - Immunity Requirements
Ta slovenski standard je istoveten z: EN 55035:2017
ICS:
33.100.20 Imunost Immunity
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 55035
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2017
ICS 33.100.20
English Version
Electromagnetic compatibility of multimedia equipment -
Immunity requirements
(CISPR 35:2016 , modified)
Compatibilité électromagnétique des équipements Elektromagnetische Verträglichkeit von Multimediageräten -
multimédia - Exigences d'immunité Anforderungen zur Störfestigkeit
(CISPR 35:2016 , modifiée) (CISPR 35:2016 , modifiziert)
This European Standard was approved by CENELEC on 2016-09-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 55035:2017 E
Contents Page
European foreword . 3
Endorsement notice . 4
1 Modification to Clause 1 "Scope" . 4
2 Modification to Clause A.4 "Modified test levels and performance criteria" . 4
3 Modification to Annexes . 4
Annex ZA (normative) Normative references to international publications with their
corresponding European publications . 5
Annex ZZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/30/EU [2014 OJ L96] aimed to be covered . 7
Annex ZZB (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/53/EU [2014 OJ L153] aimed to be covered . 8
4 Modifications to Bibliography . 9
European foreword
The text of document CISPR/I/522/FDIS, future edition 1 of CISPR 35:2016, prepared by CISPR SC I
"Electromagnetic compatibility of information technology equipment, multimedia equipment and
receivers" of CISPR "International special committee on radio interference" was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN 55035:2017.
A draft amendment, which covers common modifications to CISPR 35:2016 (CISPR/I/522/FDIS), was
prepared by CLC/TC 210 "Electromagnetic Compatibility (EMC)" and approved by CENELEC.
The following dates are fixed:
(dop) 2018-01-28
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2022-07-28
• latest date by which the national standards conflicting with
the document have to be withdrawn
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
CISPR 35:2016 are prefixed “Z”.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under mandate(s) given to CENELEC by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s).
For the relationship with EU Directive(s) and the standardization request(s), see informative
Annexes ZZA and ZZB, which are integral parts of this document.
Endorsement notice
The text of the International Standard CISPR 35:2016 was approved by CENELEC as a European
Standard with agreed common modifications.
COMMON MODIFICATIONS
1 Modification to Clause 1 "Scope"
Add the following new paragraph after the sentence "MME within the scope of CISPR 20 or CISPR 24
is within the scope of this document.":
For MME that falls within the scope of EN 300 386 or any part(s) of EN 301 489 series, the
requirements within these product specific/product family standards take precedence over the
requirements within this document.
2 Modification to Clause A.4 "Modified test levels and performance criteria"
In Table A.2 "Modified test levels for performance criterion A for the broadcast reception function",
replace the following:
The tuned channel ± 0,5 MHz (lower edge frequency - 0,5 MHz up to the upper edge frequency
+ 0,5 MHz of the tuned channel) is excluded from testing.
by the following:
Except for DVB-C, the tuned channel ± 0,5 MHz (lower edge frequency - 0,5 MHz up to the upper
edge frequency + 0,5 MHz of the tuned channel) is excluded from testing. For DVB-C, the disturbance
levels are 3 V/m or 3 V, except in the tuned channel ± 0,5 MHz (lower edge frequency - 0,5 MHz up to
the upper edge frequency + 0,5 MHz of the tuned channel), where the disturbance level is 1 V/m.
3 Modification to Annexes
Add the following new annexes.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
CISPR 16-1-2 2014 Specification for radio disturbance and EN 55016-1-2 2014
immunity measuring apparatus and
methods -
Part 1-2: Radio disturbance and
immunity measuring apparatus -
Coupling devices for conducted
disturbance measurements
IEC 61000-4-2 2008 Electromagnetic compatibility (EMC) - EN 61000-4-2 2009
Part 4-2: Testing and measurement
techniques - Electrostatic discharge
immunity test
IEC 61000-4-3 2006 Electromagnetic compatibility (EMC) - EN 61000-4-3 2006
Part 4-3: Testing and measurement
+ A1 2007 + A1 2008
techniques - Radiated, radio-frequency,
+ A2 2010 electromagnetic field immunity test + A2 2010
IEC 61000-4-4 2012 Electromagnetic compatibility (EMC) - EN 61000-4-4 2012
Part 4-4: Testing and measurement
techniques - Electrical fast
transient/burst immunity test
1)
IEC 61000-4-5 2005 Electromagnetic compatibility (EMC) - EN 61000-4-5 2006
Part 4-5: Testing and measurement
techniques - Surge immunity test
2)
IEC 61000-4-6 2008 Electromagnetic compatibility (EMC) - EN 61000-4-6 2009
Part 4-6: Testing and measurement
techniques - Immunity to conducted
disturbances, induced by radio-
frequency fields
1) EN 61000-4-5:2006 is replaced by EN 61000-4-5:2014, Electromagnetic compatibility (EMC) - Part 4-5:
Testing and measurement techniques - Surge immunity test (IEC 61000-4-5:2014).
2) EN 61000-4-6:2009 is replaced by EN 61000-4-6:2014, Electromagnetic compatibility (EMC) - Part 4-6:
Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency
fields (IEC 61000-4-6:2013).
Publication Year Title EN/HD Year
IEC 61000-4-8 2009 Electromagnetic compatibility (EMC) - EN 61000-4-8 2010
Part 4-8: Testing and measurement
techniques - Power frequency magnetic
field immunity test
IEC 61000-4-11 2004 Electromagnetic compatibility (EMC) - EN 61000-4-11 2004
Part 4-11: Testing and measurement
techniques - Voltage dips, short
interruptions and voltage variations
immunity tests
IEC 61000-4-20 2010 Electromagnetic compatibility (EMC) - EN 61000-4-20 2010
Part 4-20: Testing and measurement
techniques - Emission and immunity
testing in transverse electromagnetic
(TEM) waveguides
IEC 61000-4-21 2011 Electromagnetic compatibility (EMC) - EN 61000-4-21 2011
Part 4-21: Testing and measurement
techniques - Reverberation chamber test
methods
3)
ISO 9241-3 1992 Ergonomic requirements for office work EN 29241-3 1993
with visual display terminals (VDTs) -
Part 3: Visual display requirements
IEEE Standard - IEEE Standard for Ethernet, - -
802.3 Section Three
3) EN 29241-3:1992 is withdrawn and replaced by EN ISO 9241-302:2008, Ergonomics of human-system
interaction - Part 302: Terminology for electronic visual displays (ISO 9241-302:2008).
Annex ZZA
(informative)
Relationship between this European Standard and the essential requirements
of Directive 2014/30/EU [2014 OJ L96] aimed to be covered
This European Standard has been prepared under the European Commission standardization request
4)
C(2016) 7641 final of 30.11.2016 , ('M/552'), as regards harmonized standards in support of Directive
2014/30/EU relating to electromagnetic compatibility, to provide one voluntary means of conforming to
essential requirements of Directive 2014/30/EU of the European Parliament and of the Council of
26 February 2014 on the harmonization of the laws of the Member States relating to electromagnetic
compatibility [2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZZA.1 confers, within the limits
of the scope of this standard, a presumption of conformity with the corresponding essential
requirements of that Directive, and associated EFTA regulations.
Table ZZA.1 – Correspondence between this European Standard and the Essential
Requirements set out in Directive 2014/30/EU [2014 OJ L96]
Essential requirements of Clause(s) / sub-clause(s) Remarks / Notes
Directive 2014/30/EU of this EN
Annex I. 1(b)
Clause 5 Immunity requirements Not applicable for broadcast
(electromagnetic immunity)
receivers (Annex A) under
Table 1 – Immunity requirements
2014/30/EU
for enclosure ports
Clause 5 Immunity requirements Not applicable for broadcast
receivers (Annex A) under
Table 2 – Immunity requirements
2014/30/EU
for analogue/digital data ports
Clause 5 Immunity requirements Not applicable for broadcast
receivers (Annex A) under
Table 3 – Immunity requirements
2014/30/EU
for DC network power ports
Clause 5 Immunity requirements Not applicable for broadcast
receivers (Annex A) under
Table 4 – Immunity requirements
2014/30/EU
for AC mains power ports
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
4) COMMISSION IMPLEMENTING DECISION C(2016) 7641 final of 30.11.2016 on a standardisation request to
the European Committee for Standardisation, to the European Committee for Electrotechnical Standardisation
and to the European Telecommunications Standards Institute as regards harmonised standards in support of
Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the
harmonisation of the laws of the Member States relating to electromagnetic compatibility.
Annex ZZB
(informative)
Relationship between this European Standard and the essential requirements
of Directive 2014/53/EU [2014 OJ L153] aimed to be covered
This European Standard has been prepared under the European Commission standardization request
5)
C(2015) 5376 final of 4.8.2015 (‘M/536’), as regards harmonized standards in support of Directive
2014/53/EU relating to radio equipment, to provide one voluntary means of conforming to essential
requirements of Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014
on the harmonisation of the laws of the Member States
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.