FprEN 50561-2
(Main)Power line communication apparatus used in low voltage installations - Radio disturbance characteristics - Limits and methods of measurement - Part 2: Apparatus for access-network use
Power line communication apparatus used in low voltage installations - Radio disturbance characteristics - Limits and methods of measurement - Part 2: Apparatus for access-network use
This part of EN 50561 specifies limits and methods of measurement of radio disturbance characteristics for PLC access network communication apparatus that use the low voltage power installation as the transmission medium. This European Standard applies to equipment that communicate over this medium in the frequency range 1,606 5 MHz to 30 MHz. Procedures are given for the measurement of signals generated by the equipment and limits are specified for the frequency range 9 kHz to 400 GHz. No measurement is required at frequencies where no limit is specified. PLC apparatus in the scope of this standard is intended to operate under the responsibility of the PLC access network operator. This part does not apply to PLC apparatus solely communicating to each other in the same home; such apparatus is in the scope of EN 50561-1.
Kommunikationsgeräte auf elektrischen Niederspannungsnetzen - Funkstöreigenschaften - Grenzwerte und Messverfahren - Teil 2: Geräte für die Verwendung im Netzzugang
Appareils de communication par courant porteur utilisés dans les installations basse tension - Caractéristiques de perturbations radioélectriques - Limites et méthodes de mesure - Partie 2: Appareils pour usage en réseau d’accès
La présente partie de l’EN 50561 spécifie les limites et méthodes de mesure des caractéristiques de perturbations radioélectriques des appareils de communication par réseau d'accès CPL utilisant l'installation électrique basse tension comme moyen de transmission. La présente Norme européenne s'applique aux appareils qui communiquent par ce moyen dans la plage de fréquences comprises entre 1,606 5 MHz et 30 MHz. Des procédures sont fournies pour le mesurage des signaux produits par les appareils et des limites sont spécifiées pour la plage de fréquences comprises entre 9 kHz et 400 GHz. Aucun mesurage n'est nécessaire aux fréquences pour lesquelles des limites ne sont pas spécifiées.
Naprave za komunikacijo po napajalnih vodih nizkonapetostnih inštalacij - Karakteristike občutljivosti za radijske motnje - Mejne vrednosti in merilne metode - 2. del: Naprave za uporabo v dostopnih omrežjih
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 50561-2:2015
01-julij-2015
1DSUDYH]DNRPXQLNDFLMRSRQDSDMDOQLKYRGLKQL]NRQDSHWRVWQLKLQãWDODFLM
.DUDNWHULVWLNHREþXWOMLYRVWL]DUDGLMVNHPRWQMH0HMQHYUHGQRVWLLQPHULOQHPHWRGH
GHO 1DSUDYH]DXSRUDERYGRVWRSQLKRPUHåMLK
Powerline communication apparatus used in low voltage installations - Radio disturbance
characteristics - Limits and methods of measurement - Part 2: Apparatus for access-
network use
Appareils de communication par courant porteur utilisés dans les installations basse
tension - Caractéristiques de perturbations radioélectriques - Limites et méthodes de
mesure - Partie 1: Appareils pour usage en réseau d’accès
Ta slovenski standard je istoveten z: prEN 50561-2:2015
ICS:
33.040.60 Telekomunikacije po Powerline
elektroenergetskih vodih telecommunications
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
oSIST prEN 50561-2:2015 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN 50561-2:2015
oSIST prEN 50561-2:2015
EUROPEAN STANDARD DRAFT
prEN 50561-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2015
ICS 33.040.60; 33.100.01
English Version
Powerline communication apparatus used in low voltage
installations - Radio disturbance characteristics - Limits and
methods of measurement - Part 2: Apparatus for access-network
use
Appareils de communication par courant porteur utilisés To be completed
dans les installations basse tension - Caractéristiques de
perturbations radioélectriques - Limites et méthodes de
mesure - Partie 1: Appareils pour usage en réseau d'accès
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2015-08-29.
It has been drawn up by CLC/TC 210.
If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 23146 Ref. No. prEN 50561-2 E
oSIST prEN 50561-2:2015
prEN 50561-2:2015 (E)
Contents Page
Foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions. 6
4 Requirement for conducted disturbances at AC mains power ports . 8
5 Requirement for conducted disturbances at telecommunication/network ports . 8
6 Requirements for conducted disturbances and communications signals at PLC ports . 8
6.1 General requirements . 8
6.2 Specific requirements for Dynamic Frequency Exclusion . 10
6.3 Specific requirements for remote dynamic frequency inclusion . 11
7 Requirement for radiated disturbances. 12
8 Measurement conditions for PLC ports . 12
9 Measurement methods and procedures for PLC ports . 12
9.1 Conducted unsymmetrical disturbances . 12
9.2 Dynamic power control . 13
9.3 Cognitive frequency exclusion . 14
9.4 Testing compliance with remote dynamic frequency inclusion . 15
9.5 Conducted asymmetric disturbances . 15
10 Measurement Uncertainty . 16
Annex A (normative) Excluded frequency ranges . 17
Annex B (normative) Impedance Stabilization Network (ISN) for asymmetric disturbance
measurements . 19
Annex C (informative) Cognitive Frequency Exclusion . 21
C.1 Abbreviations . 21
C.2 PLC apparatus Broadcast Radio detection . 21
C.2.1 Overview . 21
C.2.2 Noise Floor . 21
C.2.3 Levels and Thresholds . 21
C.3 Verification of the cognitive frequency exclusion implementation . 22
C.3.1 Measurement arrangement . 22
C.3.2 Spectrum Analyser Settings . 22
C.3.3 Artificial Signal Ingress . 22
C.3.4 Levels and thresholds at verification-bench . 22
C.3.5 Test procedure . 23
C.4 Test Signals . 23
Annex ZZ (informative) Coverage of Essential Requirements of EC Directives. 25
oSIST prEN 50561-2:2015
prEN 50561-2:2015 (E)
Bibliography . 26
Tables and Figures
Table 1 — Limits for conducted disturbances . 9
Table 2 — Maximum PLC transmit signal level between 1,6065 MHz and 30 MHz . 10
Figure 1 — Minimum requirements for a dynamically excluded frequency range . 11
Figure 2 — Test arrangement for measuring the PLC port with an AMN . 13
Figure 3 — Example coupling system . 13
Figure 4 — Example test equipment arrangement for measuring PLC transmit signal levels . 14
Figure 5 — Example schematic of 100 Ω to 50 Ω Balun . 14
Figure 6 — Test arrangement for measuring the conducted asymmetric disturbances from the PLC
port . 16
Table A.1 — Permanently excluded frequency ranges . 17
Table A.2 — Permanent or dynamically excluded frequency ranges . 18
Figure B.1 — Example circuit schematic for ISN . 19
Figure B.2 — Arrangement for measurement of the ISN common mode decoupling attenuation
(isolation) (excluding the Coupling System). 20
oSIST prEN 50561-2:2015
prEN 50561-2:2015 (E)
Foreword
This document [prEN 50561-2:2015] has been prepared by CLC/TC 210 “Electromagnetic Compatibility
(EMC)”.
This document is currently submitted to the Enquiry.
This document has been prepared under a mandate given to CENELEC by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive(s).
The following dates are proposed:
– latest date by which the existence of the EN (doa) dor + 6 months
has to be announced at national level
– latest date by which the EN has to be implemented (dop) dor + 12 months
at national level by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) dor + 36 months
with the EN have to be withdrawn (to be confirmed or
modified when voting)
This document has been prepared under a mandate given to CENELEC by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
EN 50561 is currently composed of the following parts:
— EN 50561-1, Power line communication apparatus used in low-voltage installations — Radio
disturbance characteristics — Limits and methods of measurement — Part 1: Apparatus for in-home
use;
— prEN 50561-2, Powerline communication apparatus used in low voltage installations — Radio
disturbance characteristics — Limits and methods of measurement — Part 2: Apparatus for access-
network use (the present document).
The scope is extended to the whole radio-frequency range from 9 kHz to 400 GHz, but limits are formulated
only in restricted frequency bands, which are considered sufficient to reach adequate emission levels to
protect radio broadcast and telecommunication services and to allow other apparatus to operate as intended
at reasonable distance.
oSIST prEN 50561-2:2015
prEN 50561-2:2015 (E)
Introduction
CENELEC draws attention to the fact that it is claimed that compliance with this document may involve the
use of a patent given in EN 50561-1:2013.
CENELEC takes no position concerning the evidence, validity and scope of this patent right.
The holder of this patent right has assured CENELEC that he is willing to negotiate licenses under
reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect,
the statement of the holder of this patent right is registered with CENELEC. Information may be obtained
from:
Sony Cooperation
Hiroshi Kamitani
IP Alliance and Licensing Department
1-7-1 Konan, Minato-ku, Tokyo 108-0075, Japan
Tel: +81-3-6748-3505
Fax: +81-6748-3544
Hiroshi.Kamitani@jp.sony.com
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights other than those identified above. CENELEC shall not be held responsible for identifying any or all
such patent rights
oSIST prEN 50561-2:2015
prEN 50561-2:2015 (E)
1 Scope
This part of EN 50561 specifies limits and methods of measurement of radio disturbance characteristics for
PLC access network communication apparatus that use the low voltage power installation as the
transmission medium. This European Standard applies to equipment that communicate over this medium in
the frequency range 1,606 5 MHz to 30 MHz.
Procedures are given for the measurement of signals generated by the equipment and limits are specified for
the frequency range 9 kHz to 400 GHz. No measurement is required at frequencies where no limit is
specified.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applie
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.