IEC 60317-15:2004+AMD1:2010 CSV

Specifications for particular types of winding wires - Part 15: Polyesterimide enamelled round aluminium wire, class 180

IEC 60317-15:2004+A1:2010 Specifies the requirements of enamelled round aluminium winding wire of class 180 with a sole coating based on polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. Class 180 is a thermal class that requires a minimum temperature index of 180 and a heat shock temperature of at least 200 °C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor diameters covered by this standard is as follows:
- grade 1: 0,400 mm up to and including 1,600 mm;
- grade 2: 0,400 mm up to and including 5,000 mm.
The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3. The main changes with respect to the previous edition are listed below:
- new requirements for appearance, Subclause 3.2, added;
- springiness test, Clause 7, determined to be inappropriate;
- cut-through test, Clause 10, determined to be inappropriate;
- high temperature failure test, Clause 22, deleted;
- new pin hole test, Clause 23, added
This publication is to be read in conjunction with  IEC 60317-0-3:2008.
This consolidated version consists of the third edition (2004) and its amendment 1 (2010). Therefore, no need to order amendment in addition to this publication.

Spécifications pour types particuliers de fils de bobinage - Partie 15: Fil de section circulaire en aluminium émaillé avec polyesterimide, classe 180

La CEI 60317-15:2004+A1:2010 Spécifie les exigences concernant les fils de bobinage de section circulaire en aluminium émaillé de classe 180 avec un revêtement unique à base de résine polyesterimide qui peut être modifiée pour autant que cette résine conserve l'identité chimique de la résine initiale et réponde à toutes les exigences du fil. La classe 180 est une classe thermique qui exige un indice de température minimal de 180 et une température de choc thermique d'au moins 200 °C. La température en degrés Celsius correspondant à l'indice de température n'est pas nécessairement celle à laquelle il est recommandé d'utiliser le fil; cela dépendra de beaucoup de facteurs, y compris du type d'équipement considéré. La gamme des diamètres nominaux des conducteurs couverte par la présente norme est la suivante:
- grade 1: 0,400 mm jusque et y compris 1,600 mm;
- grade 2: 0,400 mm jusque et y compris 5,000 mm.
Les diamètres nominaux des conducteurs sont spécifiés dans l'Article 4 de la CEI 60317-0-3. Les modifications principales par rapport à l'édition précédente sont les suivantes:
- nouvelles exigences pour les aspects, Paragraphe 3.2, ajouté;
- essai sur l'effet de ressort, Article 7, déterminé comme étant non applicable;
- essai de thermoplasticité, Article 10, déterminé comme étant non applicable;
- essai de défaillance à haute température, Article 22, supprimé;
- nouvel essai de détection des micro-fissures en immersion, Article 23, ajouté.
Cette publication doit être lue conjointement avec la  CEI 60317-0-3:2008.
Cette version consolidée comprend la troisième édition (2004) et son amendement 1 (2010). Il n'est donc pas nécessaire de commander l'amendement avec cette publication.

General Information

• Status: Published
• Publication Date: 15-Jun-2010
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 19.040 - Environmental testing
• ICS: 29.060.10 - Wires
• Technical Committee: TC 55 - Winding wires
• Current Stage: PPUB - Publication issued
• Start Date: 16-Jun-2010
• Completion Date: 16-Jun-2010

Standards Content (Sample)

IEC 60317-15
®
Edition 3.1 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Specifications for particular types of winding wires –
Part 15: Polyesterimide enamelled round aluminium wire, class 180

Spécifications pour types particuliers de fils de bobinage –
Partie 15: Fil de section circulaire en aluminium émaillé avec polyesterimide,
classe 180
IEC 60317-15:2004+A1:2010

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2010 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]


A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]

---------------------- Page: 2 ----------------------
IEC 60317-15
®
Edition 3.1 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Specifications for particular types of winding wires –
Part 15: Polyesterimide enamelled round aluminium wire, class 180

Spécifications pour types particuliers de fils de bobinage –
Partie 15: Fil de section circulaire en aluminium émaillé avec polyesterimide,
classe 180

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CC
CODE PRIX
ICS 29.060.10 ISBN 978-2-88910-952-4
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 3 ----------------------
– 2 – 60317-15 © IEC:2004+A1:2010
CONTENTS
FOREWORD.3
INTRODUCTION.5

1 Scope.6
2 Normative references .6
3 Definitions and general notes on methods of test and appearance.7
3.1 Definitions and general notes on methods of test .7
3.2 Appearance.7
4 Dimensions .7
5 Electrical resistance .7
6 Elongation .7
7 Springiness .7
8 Flexibility and adherence.7
9 Heat shock .7
10 Cut-through .7
11 Resistance to abrasion (nominal conductor diameters up to and including 2,500 mm) .7
12 Resistance to solvents.8
13 Breakdown voltage .8
14 Continuity of insulation .8
15 Temperature index .8
16 Resistance to refrigerants.8
17 Solderability .9
18 Heat or solvent bonding.9
19 Dielectric dissipation factor.9
20 Resistance to transformer oil .9
21 Loss of mass .9
23 Pin hole test .9
30 Packaging .9

Table 1 – Résistance to abrasion.8

---------------------- Page: 4 ----------------------
60317-15 © IEC:2004+A1:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –

Part 15: Polyesterimide enamelled round aluminium wire,
class 180



FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

This consolidated version of IEC 60317-15 consists of the third edition (2004)
[documents 55/908/FDIS and 55/914/RVD] and its amendment 1 (2010) [documents
55/1121/CDV and 55/1149/RVC]. It bears the edition number 3.1.
The technical content is therefore identical to the base edition and its amendment and
has been prepared for user convenience. A vertical line in the margin shows where the
base publication has been modified by amendment 1. Additions and deletions are
displayed in red, with deletions being struck through.

---------------------- Page: 5 ----------------------
– 4 – 60317-15 © IEC:2004+A1:2010
International Standard IEC 60317-15 has been prepared by IEC technical committee 55:
Winding wires.
The main changes with respect to the previous edition are listed below:
– new requirements for appearance, Subclause 3.2, added;
– springiness test, Clause 7, determined to be inappropriate;
– cut-through test, Clause 10, determined to be inappropriate;
– high temperature failure test, Clause 22, deleted;
– new pin hole test, Clause 23, added.
This International Standard is to be read in conjunction with IEC 60317-0-3.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of the base publication and its amendments will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this publication using a colour printer.

---------------------- Page: 6 ----------------------
60317-15 © IEC:2004+A1:2010 – 5 –
INTRODUCTION
This part of IEC 60317 is one of a series which deals with insulated wires used for windings in
electrical equipment. The series has three groups describing
1) winding wires – Test methods (IEC 60851);
2) specifications for particular types of winding wires (IEC 60317);
3) packaging of winding wires (IEC 60264).

---------------------- Page: 7 ----------------------
– 6 – 60317-15 © IEC:2004+A1:2010
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –

Part 15: Polyesterimide enamelled round aluminium wire,
class 180



1 Scope
This part of IEC 60317 specifies the requirements of enamelled round aluminium winding wire
of class 180 with a sole coating based on polyesterimide resin, which may be modified
providing it retains the chemical identity of the original resin and meets all specified wire
requirements.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance or application characteristics.
Class 180 is a thermal class that requires a minimum temperature index of 180 and a heat
shock temperature of at least 200 °C.
The temperature in degrees Celsius corresponding to the temperature index is not necessarily
that at which it is recommended that the wire be operated and this will depend on many
factors, including the type of equipment involved.
The range of nominal conductor diameters covered by this standard is as follows:
– grade 1: 0,400 mm up to and including 1,600 mm;
– grade 2: 0,400 mm up to and including 5,000 mm.
The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60317-0-3, Specifications for particular types of winding wires – Part 0: General require-
ments – Section 3: Enamelled round aluminium wire
Amendment 1 (1999)
1
Amendment 2
IEC 60317-0-3:2008, Specifications for particular types of winding wires – Part 0-3: General
requirements – Enamelled round aluminium wire
IEC 60851-4:1996, Winding wires – Test methods – Part 4: Chemical properties
Amendment 1 (1997)
Amendment 2 (2005)
___________
1
To be published.

---------------------- Page: 8 ----------------------
60317-15 © IEC:2004+A1:2010 – 7 –
3 Definitions and general notes on methods of test and appearance
3.1 Definitions and general notes on methods of test
For definitions and general notes on methods of test, see Clause 3 of IEC 60317-0-3.
In case of inconsistencies between IEC 60317-0-3 and this standard, IEC 60317-15 shall
prevail.
3.2 Appearance
See Clause 3 of IEC 60317-0-3.
4 Dimensions
See Clause 4 of IEC 60317-0-3.
5 Electrical resistance
See Clause 5 of IEC 60317-0-3.
6 Elongation
See Clause 6 of IEC 60317-0-3.
7 Springiness
Test inappropriate.
8 Flexibility and adherence
See Clause 8 of IEC 60317-0-3.
9 Heat shock
See Clause 9 of IEC 60317-0-3, where the minimum heat shock temperature shall be 200 °C.
10 Cut-through
Test inappropriate.
11 Resistance to abrasion
(nominal conductor diameters up to and including 2,500 mm)
The wire shall meet the requirements given in Table 1.

---------------------- Page
...