IEC 61196-5:2018

Coaxial communication cables - Part 5: Sectional specification for CATV trunk and distribution cables

IEC 61196-5:2018(E), which is a sectional specification, applies to coaxial cables for analogue and digital one- and two-way signal transmission, e.g. for cable networks for television signals, sound signals and interactive services in accordance with IEC 60728-1, IEC 60728-1-1, IEC 60728-101, IEC 60728-10, ISO/IEC 11801-1 and ISO/IEC 11801-4. This includes also the transmission of BCT signals provided by a CATV, MATV or SMATV cable networks.
This document specifies the test procedures and requirements for trunk and distribution cables for temperatures between −40 °C and +65 °C and in the frequency range of 5 MHz to 2 000 MHz.
This third edition cancels and replaces the second edition published in 2012. This edition constitutes a technical revision.
This edition includes the following significant technical change with respect to the previous edition:
a) 1 Scope: revised, frequency range extended to 2 000 MHz;
b) 4.3 Dielectric: life expectancy of the dielectric is proved by oxidative induction time (OIT) test before and after ageing according to IEC 60811-410;
c) Annex A: Table A.1, Cable types added.

General Information

• Status: Published
• Publication Date: 11-Jan-2018
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 29.240.20 - Power transmission and distribution lines
• ICS: 33.120.10 - Coaxial cables. Waveguides
• Technical Committee: SC 46A - Coaxial cables
• Drafting Committee: WG 3 - TC 46/SC 46A/WG 3
• Current Stage: DELPUB - Deleted Publication
• Start Date: 10-Sep-2021
• Completion Date: 16-Dec-2022

Relations

• Revised: IEC 61196-5:2022 - Coaxial communication cables - Part 5: Sectional specification for CATV trunk and distribution cables
• Effective Date: 05-Sep-2023
• Revises: IEC 61196-5:2012 - Coaxial communication cables - Part 5: Sectional specification for CATV trunk and distribution cables
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 61196-5 ®
Edition 3.0 2018-01
INTERNATIONAL
STANDARD
Coaxial communication cables –
Part 5: Sectional specification for CATV trunk and distribution cables
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: [phone]
3, rue de Varembé [e-mail]
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: [e-mail].
IEC 61196-5 ®
Edition 3.0 2018-01
INTERNATIONAL
STANDARD
Coaxial communication cables –

Part 5: Sectional specification for CATV trunk and distribution cables

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.120.10 ISBN 978-2-8322-5258-1

– 2 – IEC 61196-5:2018 © IEC 2018
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Materials and cable construction . 7
4.1 Cable construction . 7
4.2 Inner conductor . 7
4.2.1 Conductor material . 7
4.2.2 Conductor construction . 7
4.3 Dielectric . 8
4.4 Outer conductor or screen . 8
4.5 Sheath . 8
4.6 Completed cable . 9
5 Standard ratings and characteristics . 9
6 Identification and marking . 9
6.1 Cable identification . 9
6.2 Cable marking . 9
6.3 Labelling . 9
7 Tests for completed cables . 9
7.1 General . 9
7.2 Electrical testing of the finished cable . 9
7.3 High-frequency electrical and transmission test procedures and
requirements . 10
7.4 Environmental test procedures and requirements of the finished cable . 11
7.5 Test procedures and requirements of mechanical characteristics of the
finished cable. 12
7.6 Fire performance . 13
8 Quality assessment . 13
9 Delivery and storage . 13
Annex A (informative) Cable types . 14

Table 1 – Low-frequency and DC test procedures and requirements . 10
Table 2 – High-frequency electrical and transmission test procedures and requirements . 10
Table 3 – Environmental test procedures and requirements of the finished cable . 11
Table 4 – Test procedures and requirements of mechanical characteristics of the
finished cable . 12
Table 5 – Fire performance requirements . 13
Table A.1 – Distribution and trunk cables – Preferred nominal dimensions and ratings . 14

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
COAXIAL COMMUNICATION CABLES –

Part 5: Sectional specification for CATV trunk
and distribution cables
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61196-5 has been prepared by subcommittee 46A: Coaxial cables,
of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF and microwave
passive components and accessories.
This third edition cancels and replaces the second edition published in 2012. This edition
constitutes a technical revision.
This edition includes the following significant technical change with respect to the previous
edition:
a) 1 Scope: revised, frequency range extended to 2 000 MHz;
b) 4.3 Dielectric: life expectancy of the dielectric is proved by oxidative induction time (OIT)
test before and after ageing according to IEC 60811-410;
c) Annex A: Table A.1, Cable types added.

– 4 – IEC 61196-5:2018 © IEC 2018
The text of this International Standard is based on the following documents:
FDIS Report on voting
46A/1351/FDIS 46A/1357/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
This International Standard is to be used in conjunction with IEC 61196-1:2005.
A list of all parts of the IEC 61196 series, published under the general title Coaxial
communication cables, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

COAXIAL COMMUNICATION CABLES –

Part 5: Sectional specification for CATV trunk
and distribution cables
1 Scope
This part of IEC 61196, which is a sectional specification, applies to coaxial cables for
analogue and digital one- and two-way signal transmission, e.g. for cable networks for
television signals, sound signals and interactive services in accordance with IEC 60728-1,
IEC 60728-1-1, IEC 60728-101, IEC 60728-10, ISO/IEC 11801-1 and ISO/IEC 11801-4. This
includes also the transmission of BCT signals provided by a CATV, MATV or SMATV cable
networks.
This document specifies the test procedures and requirements for trunk and distribution
cables for temperatures between −40 °C and +65 °C and in the frequency range of 5 MHz to
2 000 MHz.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60068-1:2013, Environmental testing – Part 1: General and guidance
IEC 60068-2-78, Environmental testing – Part 2-78: Tests – Test Cab: Damp heat, steady
state
IEC 60096-0-1, Radio Frequency cables – Part 0-1: Guide to the design of detail
specifications – Coaxial cables
IEC 60728-1, Cable networks for television signals, sound signals and interactive services –
Part 1: System performance of forward paths
IEC 60811-410, Electric
...