IEC PAS 63015:2016

Definition of "Low-Halogen" for electronic products

IEC PAS 63015:2016(E) provides terms and definitions for "low-halogen" electronic products that have the potential to contain the halogens bromine (Br) and chlorine (Cl) from the use of BFRs, CFRs, and PVC, and recommends methods for marking and labeling. This standard may be applied to all nonmetallic and nonceramic materials within electronic products. It establishes the maximum concentration level for the halogens bromine (Br) and chlorine (Cl) from the use of BFRs, CFRs, and PVC. While the halogen group contains fluorine, chlorine, bromine, iodine, and astatine, this document will use the term "low-halogen" to refer only to bromine and chlorine. Refer to Annex C for further explanation for exclusion of astatine, iodine and fluorine.

General Information

• Status: Withdrawn
• Publication Date: 14-Jun-2016
• Withdrawal Date: 08-Nov-2018
• ICS: 01.040.71 - Chemical technology (Vocabularies)
• ICS: 13.030.10 - Solid wastes
• Technical Committee: TC 111 - Environmental standardization for electrical and electronic products and systems
• Current Stage: WPUB - Publication withdrawn
• Start Date: 09-Nov-2018
• Completion Date: 09-Nov-2018

Standards Content (Sample)

IEC PAS 63015 ®
Edition 1.0 2016-06
PUBLICLY AVAILABLE
SPECIFICATION
PRE-STANDARD
Definition of “Low-Halogen” for electronic products

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from

either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or

your local IEC member National Committee for further information.

IEC Central Office Tel.: [phone]
3, rue de Varembé Fax: [phone]

CH-1211 Geneva 20 [e-mail]
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: [e-mail].
IEC PAS 63015 ®
Edition 1.0 2016-06
PUBLICLY AVAILABLE
SPECIFICATION
PRE-STANDARD
Definition of “Low-Halogen” for electronic products

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 01.040.71; 13.030.10 ISBN 978-2-8322-3471-6

– 2 – IEC PAS 63015:2016 © IEC 2016

CONTENTS
FOREWORD . 3

INTRODUCTION . 5

1 Scope . 6

2 Normative references. 6

3 Terms, definitions and abbreviated terms . 7

4 Requirements for low-halogen electronic products . 8

5 Compliance process for low-halogen electronic materials and components . 9
6 Marking and labeling for “low-halogen” electronic products . 9
6.1 Marking of printed boards . 9
6.2 Marking of mechanical plastics . 9
6.3 Marking of passive and solid-state devices, cables, and other components of
an electronic product . 9
6.4 Marking of electronic products . 10
Annex A (informative)  Where BFRs, CFRs, and PVC are used in electronic or
electrical products . 11
Annex B (informative)  Suggested test protocols – Low-halogen process flow . 12
B.1 Low halogen process flow . 12
B.2 Low halogen process flow verbiage . 13
Annex C (informative) Clarification for including only bromine and chlorine in the
definition of low-halogen materials . 14
Annex D (informative) Differences between JS709B and JS709A . 15
Bibliography . 16

Table A.1 – General presence of bromine and chlorine in BFRs, CFRs, and PVC in
electronics and electrical products . 11

INTERNATIONAL ELECTROTECHNICAL COMMISSION

____________
DEFINITION OF “LOW-HALOGEN” FOR ELECTRONIC PRODUCTS

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
A PAS is a technical specification not fulfilling the requirements for a standard, but made
available to the public.
IEC PAS 63015, submitted by JEDEC/ECA has been processed by IEC technical
committee 111: Environmental standardization for electrical and electronic products and
systems. It is based on Joint JEDEC/ECA Standard No. 709B. The structure and editorial
rules used in this PAS reflect the practice of the organization which submitted it.
The text of this PAS is based on the This PAS was approved for
following document: publication by the P-members of the
committee concerned as indicated in
the following document
Draft PAS Report on voting
111/382/PAS 111/417/RVD
Following publication of this PAS, the technical committee or subcommittee concerned may
transform it into an International Standard.
This PAS shall remain valid for an initial maximum period of 3 years starting from the
publication date. The validity may be extended for a single period up to a maximum of

– 4 – IEC PAS 63015:2016 © IEC 2016

3 years, at the end of which it shall be published as another type of normative document, or

shall be withdrawn.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates

that it contains colours which are considered to be useful for the correct

understanding of its contents. Users should therefore print this document using a

colour printer.
INTRODUCTION
Halogenated polymeric materials and compounds are used in various engineering

applications, including flame retardation. Several decades of use have proven these materials

and compounds to be reliable and cost-effective. The electronic industry seeks to reduce the

overall environmental impact of our products by working to develop reliable and cost-effective

alternatives to these materials and compounds. However, the timetable for broad-scale

adoption of low-halogen materials is difficult to predict, because applications such as complex

multilayer PCBs and large molded integrated circuits will require further investigation and

qualification of new materials.

The halogen group contains fluorine, chlorine, bromine, iodine, and astatine; however, this
document will use the term “low-halogen” to refer only to bromine and chlorine to be
consistent with the International Electrotechnical Commission (IEC) and IPC definitions of
“halogen-free” (see Clause 2). Refer to Annex C for further explanation for exclusion of
astatine, iodine and fluorine. In this document, the term “low-halogen” is used to identify a
material that contains low concentrations of bromine and chlorine from brominated and
chlorinated flame retardants (BFRs, CFRs) and polyvinyl chloride (PVC).

– 6 – IEC PAS 63015:2016 © IEC 2016

DEFINITION OF “LOW-HALOGEN” FOR ELECTRONIC PRODUCTS

1 Scope
This document provides terms and definitions for “low-halogen” electronic products that have

the potential to contain the halogens bromine (Br) and chlorine (Cl) from the use of BFRs,

CFRs, and PVC, and recommends methods for marking and labeling. This standard may be

applied to all nonmetallic and nonceramic materials within electronic products including, but

not limited to, materials in the following components commonly found in electronic products:
1) transistors, integrated circuits, modules consisting mainly of integrated circuits (e.g.
multichip, hybrid), and memory modules;
2) resistors, capacitors, relays, inductors, and connectors;
3) printed circuit board assemblies (PCBAs) including components;
4) plastic in cables, sockets, switches and external wiring;
5) mechanical plastics (enclosures, fans, etc.);
6) films, tapes, inks, and adhesives;
7) soldering flux residues (when present);
8) sound, shock, and vibration dampeners (foams, resins, etc.).
This document establishes the maximum concentration level for the halogens bromine (Br)
and chlorine (Cl) from the use of BFRs, CFRs, and PVC. While the halogen group contains
fluorine, chlorine, bromine, iodine, and astatine, this document will use the term “low-halogen”
to refer only to bromine and chlorine. Refer to Annex C for further explanation for exclusion of
astatine, iodine and fluorine.
NOTE The definition of “low-halogen” is different from the term “halogen-free” as described in IEC 61249-2
sectional standard related to non-halogenated base material and as defined in the J-STD-609A marking and
labeling standard; standards that pertain only to printed boards and are currently in use in the electronics and
solid-state industries.
BFRs, CFRs, and PVC in materials that may be used during processing, in product delivery
systems, or in packaging, but do not remain within the final product are not included in the
scope of this document.
...