Petroleum products — Fuels (class F) — Liquefied petroleum gases — Specifications

ISO 9162:2013 specifies required characteristics and additional information to be supplied to the purchaser by the vendor of those products commonly referred to as liquefied petroleum gases (see ISO 8216‑3) and is intended to apply to international transfers of commercial propane and commercial butane. ISO 9162:2013 is neither intended nor expected to replace or encroach upon national standards of any country since each country is subject to different regulations, codes, industry practices and market utilization.

Produits pétroliers — Combustibles (classe F) — Gaz de pétrole liquéfiés — Spécifications

L'ISO 9162:2013 spécifie les caractéristiques exigées ainsi que les informations complémentaires qui doivent être fournies à l'acheteur par le fournisseur de produits couramment dénommés gaz de pétrole liquéfiés (voir l'ISO 8216‑3). Elle est conçue pour s'appliquer aux transferts internationaux de propane commercial et de butane commercial. Le but de l'ISO 9162:2013 n'est pas de remplacer les normes nationales de chaque pays, ni même d'empiéter sur elles, puisque chaque pays a des réglementations, codes, pratiques industrielles et utilisation des marchés différents. Pour des utilisations particulières, il convient de formuler des spécifications qui répondent à leurs besoins spécifiques et qui soient conformes aux normes nationales et codes de sécurité applicables.

Naftni proizvodi - Goriva (razred F) - Utekočinjeni naftni plini - Specifikacije

Ta mednarodni standard določa zahtevane lastnosti in dodatne informacije, ki jih kupcu predloži dobavitelj, za proizvode, ki se običajno imenujejo utekočinjeni naftni plini (glej standard ISO 8216-3), ter je namenjen uporabi za mednarodne prenose komercialnega propana in komercialnega butana. Ta mednarodni standard ni namenjen nadomestitvi ali poseganju v nacionalne standarde katere koli države niti se to od njega ne pričakuje, saj v vsaki državi veljajo drugačni predpisi, kodeksi, industrijske prakse in uporaba trga.

General Information

Status
Published
Publication Date
21-Jul-2013
Current Stage
9020 - International Standard under periodical review
Start Date
15-Jan-2024
Completion Date
15-Jan-2024

Relations

Buy Standard

Standard
ISO 9162:2014
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 9162:2013 - Petroleum products -- Fuels (class F) -- Liquefied petroleum gases -- Specifications
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 9162:2013 - Produits pétroliers -- Combustibles (classe F) -- Gaz de pétrole liquéfiés -- Spécifications
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 9162:2014
01-januar-2014
1DGRPHãþD
SIST ISO 9162:1998
1DIWQLSURL]YRGL*RULYD UD]UHG) 8WHNRþLQMHQLQDIWQLSOLQL6SHFLILNDFLMH
Petroleum products - Fuels (class F) - Liquefied petroleum gases - Specifications
Produits pétroliers - Combustibles (classe F) - Gaz de pétrole liquéfiés - Spécifications
Ta slovenski standard je istoveten z: ISO 9162:2013
ICS:
75.160.30 Plinska goriva Gaseous fuels
SIST ISO 9162:2014 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 9162:2014

---------------------- Page: 2 ----------------------

SIST ISO 9162:2014
INTERNATIONAL ISO
STANDARD 9162
Second edition
2013-07-15
Petroleum products — Fuels (class
F) — Liquefied petroleum gases —
Specifications
Produits pétroliers — Combustibles (classe F) — Gaz de pétrole
liquéfiés — Spécifications
Reference number
ISO 9162:2013(E)
©
ISO 2013

---------------------- Page: 3 ----------------------

SIST ISO 9162:2014
ISO 9162:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 9162:2014
ISO 9162:2013(E)

Contents  Page
Foreword .iv
1 Scope . 1
2  Normative references . 1
3  Requirements . 2
3.1 General . 2
3.2 Water content . 2
4  Precision and interpretation of test results . 3
5  Documentation . 3
6  Sampling . 3
Annex A (informative) Evaporation residue of liquefied petroleum gases .4
© ISO 2013 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 9162:2014
ISO 9162:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This docum
...

INTERNATIONAL ISO
STANDARD 9162
Second edition
2013-07-15
Petroleum products — Fuels (class
F) — Liquefied petroleum gases —
Specifications
Produits pétroliers — Combustibles (classe F) — Gaz de pétrole
liquéfiés — Spécifications
Reference number
ISO 9162:2013(E)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 9162:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 9162:2013(E)

Contents  Page
Foreword .iv
1 Scope . 1
2  Normative references . 1
3  Requirements . 2
3.1 General . 2
3.2 Water content . 2
4  Precision and interpretation of test results . 3
5  Documentation . 3
6  Sampling . 3
Annex A (informative) Evaporation residue of liquefied petroleum gases .4
© ISO 2013 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 9162:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 28, Petroleum products and lubricants,
Subcommittee SC 4, Classifications and specifications, WG 5, Ga
...

NORME ISO
INTERNATIONALE 9162
Deuxième édition
2013-07-15
Produits pétroliers — Combustibles
(classe F) — Gaz de pétrole liquéfiés
— Spécifications
Petroleum products — Fuels (class F) — Liquefied petroleum gases —
Specifications
Numéro de référence
ISO 9162:2013(F)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 9162:2013(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2013
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2013 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 9162:2013(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Exigences . 2
3.1 Généralités . 2
3.2 Teneur en eau . 3
4 Fidélité et interprétation des résultats d’essai . 3
5 Documentation . 3
6 Échantillonnage . 3
Annexe A (informative) Résidu d’évaporation des gaz de pétrole liquéfiés .4
© ISO 2013 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 9162:2013(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (CEI) en ce qui concerne
la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/CEI, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/CEI, Partie 2, www.iso.
org/directives.
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les
références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l’élaboration
du document sont indiqués dans l’Introduction et/ou sur la liste ISO des déclarations de brevets reçues,
www.iso.org/patents.
Les éventuelles appellations commerciales utilisées
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.