Welding for aerospace applications — Qualification test for welders and welding operators — Fusion welding of metallic components — Amendment 1

Soudage pour applications aérospatiales — Épreuve de qualification pour soudeurs et opérateurs — Soudage par fusion des composants métalliques — Amendement 1

Varjenje v aeronavtiki - Preskušanje usposobljenosti varilcev in operaterjev varjenja - Talilno varjenje kovinskih sestavnih delov - Dopolnilo A1

General Information

Status
Withdrawn
Publication Date
07-Nov-2012
Withdrawal Date
07-Nov-2012
Current Stage
9599 - Withdrawal of International Standard
Start Date
13-Dec-2018
Completion Date
13-Dec-2018

RELATIONS

Buy Standard

Standard
ISO 24394:2008/Amd 1:2012
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview
Amendment
ISO 24394:2017/Amd 1:2017
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 24394
First edition
2008-10-15
AMENDMENT 1
2012-11-15
Corrected version
2013-05-01
Welding for aerospace applications —
Qualification test for welders and
welding operators — Fusion welding
of metallic components
AMENDMENT 1
Soudage pour applications aérospatiales — Épreuve de
qualification pour soudeurs et opérateurs — Soudage par fusion des
composants métalliques
AMENDEMENT 1
Reference number
ISO 24394:2008/Amd.1:2012(E)
ISO 2012
---------------------- Page: 1 ----------------------
ISO 24394:2008/Amd.1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 24394:2008/Amd.1:2012(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International

Standards adopted by the technical committees are circulated to the member bodies for voting.

Publication as an International Standard requires approval by at least 75 % of the member bodies

casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

Amendment 1 to ISO 24394:2008 was prepared by Technical Committee ISO/TC 44, Welding and

allied processes.

This corrected version of ISO 24394/Amd.1:2012 incorporates an updated Table 1, in which “x” replaces

“—” for D > 26 mm in:
a) TP1, PF row, butt weld columns PA and PF;
b) TP2, PF row, fillet weld column PF;
c) TP3, PF row, butt weld columns PA, PE, and PF.

Requests for official interpretations of any aspect of this amendment should be directed to the Secretariat of

ISO/TC 44 via your national standards body. A complete listing of these bodies can be found at www.iso.org.

© ISO 2012 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 24394:2008/Amd.1:2012(E)
Welding for aerospace applications — Qualification test
for welders and welding operators — Fusion welding of
metallic components
AMENDMENT 1
Page 1, Clause 2
Delete footnotes 1) and 2) and their citations from ISO 4063 and ISO 6947.
Page 3, 4.1.1
Add the following paragraph at the end of the subclause.

The welding coordinator of the plant or the fabricator shall select from Table 2 the test piece as

required for the production work on which the welder is to be employed. Two complementary

specific test pieces (TP5 and TP6) may also be chosen as defined in 4.4 and 4.8.1.

Page 3, 4.1.3
Delete this subclause.
Page 5, Table 1
Replace the existing table with that on p. 3.
Page 6, 4.8.2
Delete “.”, add “;” at the end of “g)” and add h).
h) qualification for welding positions that are not covered by Table 1.
Page 8, 5.1
© ISO 2012 – All rights reserved 1
---------------------- Page: 4 ----------------------
ISO 24394:2008/Amd.1:2012(E)
Replace the first paragraph with the following:

The candidate shall provide documented evidence of satisfactory vision in accordance with the

following requirements.

  d) Near-vision acuity shall permit reading of Times New Roman N5 maximum size or equivalent

font types (Times New Roman of 5 points vertical height where 1 point = 1/72 in ≡ 0,35 mm) at

not less than 30 cm with at least one eye, corrected or uncorrected. This test shall be conducted

with a minimum of six single spaced random capital characters.
e) Colour perception shall be examined, e.g. according to the Ishihara test.
Page 8, 5.2
Replace the second and third sentences and the note with the following:

  The welding coordinator shall have knowledge and experience relevant to the welding process,

and be acceptable to the responsible design authority or recognized examining body. The welding

coordinator may authorize another person to administer the welder or welding operator qualification

test.

NOTE 1 Example of relevant knowledge is International Welding Engineer (IWE) according to IIW IAB-

[5]
252-11.

NOTE 2 The person responsible for welder and welding operator qualification tests can differ from the

person responsible for implementing 4.1.1
Page 10, Table 2
In column 2, row “TP1”, add the following at the end of footnote .
— for materials susceptible to cracking, the welding sequence may be altered.
Page 15, Clause 9
Replace the fourth paragraph with the following.

  The person authorized to conduct the welder’s qualification test shall decide if and when a new test

can be taken. If the welder or welding operator fails the test, the candidate shall have additional

training and/or practice.
Page 15, Clause 11
Add the following final paragraph.

Qualifications to previous revisions of this International Standard remain valid within the limits

given in the preceding.
Page 16, clause 12
2 © ISO 2012 – All rights reserved
---------------------- Page: 5 ----------------------
ISO 24394:2008/Amd.1:2012(E)
Replace the third paragraph with the following.

For requalification tests, actual production parts may be used to replace test pieces, if they are

consistent with the requirements of the welding process, the material group and testing as identified

in the respective initial qualification test, e.g. requirements given in Table 1 and Table 3.

Page 17–18, Table A.1
Replace the existing Table with that on pp. 4–5.
Pages 19–20, Table A.2

In the “Unacceptable imperfections” column, row 8, “Spatter”, add a superscript , Insert the following

footnote at the bottom of the footer row.

Spatter may be acceptable on welding processes or materials where it cannot be avoided. In such cases, the

acceptability is at the discretion of the welding coordinator.
Page 30,before the bibliography
Insert Annex F, which appears on p. 6.
Page 30, Bibliography
Add the following entry:

[1] IAB-252-11, IIW guideline for international welding engineers, technologists, specialists and

practitioners — Personnel with qualification for welding coordination — Minimum requirements

for the education, examination and qualification. Available (viewed 2012-10-11) at: http://

www.iiwelding.org/WorkingUnits/QCMB_IAB/Documents/IAB-252r1-11-SV00-Guideline-for-

Personnel-with-Qualification-for-Welding-Coordination-SV.pdf
© ISO 2012 – All rights reserved 3
---------------------- Page: 6 ----------------------
ISO 24394:2008/Amd.1:2012(E)
Table 1 — Range of qualification for welding positions
Qualified welding position
Welding
position of
Plate or tube D > 26 mm Tube D ≤ 26 mm
Test piece
test piece
(see Table 2)
Butt weld Fillet weld Butt weld Fillet weld
according to
ISO 6947:2011
PA PC PE PF PA PB PC PD PF PA PC PF PB PD PF
PA x — — — — — — — — x — — — — —
PC x x — — — — — — — — x — — — —
PE x x x — — — — — — — — — — — —
TP1
PF x — — x — — — — — — — — — — —
PA — — — — x — — — — — — — — — —
PB — — — — x x — — — — — — — — —
PC — — — — x x x — — — — — — — —
TP2
PD — — — — x x — x — — — — — — —
...

SLOVENSKI STANDARD
SIST ISO 24394:2017/Amd 1:2017
01-julij-2017
Varjenje v aeronavtiki - Preskušanje usposobljenosti varilcev in operaterjev
varjenja - Talilno varjenje kovinskih sestavnih delov - Dopolnilo A1

Welding for aerospace applications - Qualification test for welders and welding operators

- Fusion welding of metallic components

Soudage pour applications aérospatiales - Épreuve de qualification pour soudeurs et

opérateurs - Soudage par fusion des composants métalliques
Ta slovenski standard je istoveten z: ISO 24394:2008/Amd 1:2012
ICS:
03.100.30 Vodenje ljudi Management of human
resources
25.160.01 Varjenje, trdo in mehko Welding, brazing and
spajkanje na splošno soldering in general
49.020 Letala in vesoljska vozila na Aircraft and space vehicles in
splošno general
SIST ISO 24394:2017/Amd 1:2017 en,fr

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 24394:2017/Amd 1:2017
---------------------- Page: 2 ----------------------
SIST ISO 24394:2017/Amd 1:2017
INTERNATIONAL ISO
STANDARD 24394
First edition
2008-10-15
AMENDMENT 1
2012-11-15
Welding for aerospace applications —
Qualification test for welders and
welding operators — Fusion welding of
metallic components
AMENDMENT 1
Soudage pour applications aérospatiales — Épreuve de qualification pour
soudeurs et opérateurs — Soudage par fusion des composants métalliques
AMENDEMENT 1
Reference number
ISO 24394:2008/Amd.1:2012(E)
ISO 2012
---------------------- Page: 3 ----------------------
SIST ISO 24394:2017/Amd 1:2017
ISO 24394:2008/Amd.1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s

member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 24394:2017/Amd 1:2017
ISO 24394:2008/Amd.1:2012(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International

Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

Amendment 1 to ISO 24394:2008 was prepared by Technical Committee ISO/TC 44, Welding and allied processes.

Requests for official interpretations of any aspect of this amendment should be directed to the Secretariat of

ISO/TC 44 via your national standards body. A complete listing of these bodies can be found at www.iso.org.

© ISO 2012 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 24394:2017/Amd 1:2017
---------------------- Page: 6 ----------------------
SIST ISO 24394:2017/Amd 1:2017
ISO 24394:2008/Amd.1:2012(E)
Welding for aerospace applications — Qualification test for
welders and welding operators — Fusion welding of metallic
components
AMENDMENT 1
Page 1, Clause 2
Delete footnotes 1) and 2) and their citations from ISO 4063 and ISO 6947.
Page 3, 4.1.1
Add the following paragraph at the end of the subclause.

The welding coordinator of the plant or the fabricator shall select from Table 2 the test piece as required for

the production work on which the welder is to be employed. Two complementary specific test pieces (TP5

and TP6) may also be chosen as defined in 4.4 and 4.8.1.
Page 3, 4.1.3
Delete this subclause.
Page 5, Table 1
Replace the existing table with that on p. 3.
Page 6, 4.8.2
Delete “.”, add “;” at the end of “g)” and add h).
h) qualification for welding positions that are not covered by Table 1.
Page 8, 5.1
Replace the first paragraph with the following:

The candidate shall provide documented evidence of satisfactory vision in accordance with the following

requirements.

a) Near-vision acuity shall permit reading of Times New Roman N5 maximum size or equivalent font

types (Times New Roman of 5 points vertical height where 1 point = 1/72 in ≡ 0,35 mm) at not less

than 30 cm with at least one eye, corrected or uncorrected. This test shall be conducted with a

minimum of six single spaced random capital characters.
b) Colour perception shall be examined, e.g. according to the Ishihara test.
© ISO 2012 – All rights reserved 1
---------------------- Page: 7 ----------------------
SIST ISO 24394:2017/Amd 1:2017
ISO 24394:2008/Amd.1:2012(E)
Page 8, 5.2
Replace the second and third sentences and the note with the following:

The welding coordinator shall have knowledge and experience relevant to the welding process, and be

acceptable to the responsible design authority or recognized examining body. The welding coordinator

may authorize another person to administer the welder or welding operator qualification test.

[5]

NOTE 1 Example of relevant knowledge is International Welding Engineer (IWE) according to IIW IAB-252-11.

NOTE 2 The person responsible for welder and welding operator qualification tests can differ from the person

responsible for implementing 4.1.1
Page 10, Table 2
In column 2, row “TP1”, add the following at the end of footnote .
— for materials susceptible to cracking, the welding sequence may be altered.
Page 15, Clause 9
Replace the fourth paragraph with the following.

The person authorized to conduct the welder’s qualification test shall decide if and when a new test can

be taken. If the welder or welding operator fails the test, the candidate shall have additional training and/or

practice.
Page 15, Clause 11
Add the following final paragraph.

Qualifications to previous revisions of this International Standard remain valid within the limits given in

the preceding.
Page 16, clause 12
Replace the third paragraph with the following.

For requalification tests, actual production parts may be used to replace test pieces, if they are consistent

with the requirements of the welding process, the material group and testing as identified in the respective

initial qualification test, e.g. requirements given in Table 1 and Table 3.
Page 17–18, Table A.1
Replace the existing Table with that on pp. 4–5.
Pages 19–20, Table A.2

In the “Unacceptable imperfections” column, row 8, “Spatter”, add a superscript , Insert the following

footnote at the bottom of the footer row.
2 © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST ISO 24394:2017/Amd 1:2017
ISO 24394:2008/Amd.1:2012(E)

Spatter may be acceptable on welding processes or materials where it cannot be avoided. In such cases, the acceptability is

at the discretion of the welding coordinator.
Page 30,before the bibliography
Insert Annex F, which appears on p. 6.
Page 30, Bibliography
Add the following entry:

[1] IAB-252-11, IIW guideline for international welding engineers, technologists, specialists and

practitioners — Personnel with qualification for welding coordination — Minimum requirements for

the education, examination and qualification. Available (viewed 2012-10-11) at: http://www.iiwelding.

org/WorkingUnits/QCMB_IAB/Documents/IAB-252r1-11-SV00-Guideline-for-Personnel-with-

Qualification-for-Welding-Coordination-SV.pdf
Table 1 — Range of qualification for welding positions
Qualified welding position
Welding
position of
Plate or tube D > 26 mm Tube D ≤ 26 mm
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.