ISO 8373:1994/Cor 1:1996
(Corrigendum)Manipulating industrial robots — Vocabulary — Technical Corrigendum 1
- BACK
- 03-Jul-1996
- 03-Jul-1996
- 01.040.25
- 25.040.30
- ISO/TC 184
Manipulating industrial robots — Vocabulary — Technical Corrigendum 1
Robots manipulateurs industriels — Vocabulaire — Rectificatif technique 1
General Information
Relations
This May Also Interest You
This document defines terms relevant to automatic end-effector exchange systems used as a part of robot systems in accordance with ISO 10218‑2.
- Standard19 pagesEnglish languagesale 15% off
- Draft19 pagesEnglish languagesale 15% off
- 14-Feb-2022
- 01.040.25
- 25.040.30
- ISO/TC 299
This document defines terms used in relation to robotics.
- Standard22 pagesEnglish languagesale 15% off
- Standard23 pagesFrench languagesale 15% off
- Draft22 pagesEnglish languagesale 15% off
- Draft22 pagesFrench languagesale 15% off
- 07-Nov-2021
- 01.040.25
- 25.040.30
- ISO/TC 299
ISO 19649:2017 defines terms relating to mobile robots that travel on a solid surface and that operate in both industrial robot and service robot applications. It defines terms used for describing mobility, locomotion and other topics relating to the navigation of mobile robots.
- Standard10 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
- 16-Mar-2017
- 01.040.25
- 25.040.30
- ISO/TC 299
- Standard35 pagesEnglish languagesale 15% off
- 01-Nov-2000
- 01.040.25
- 25.040.30
- ISO/TC 299
This document specifies a method of determining the degree of disintegration of plastic materials when exposed to a laboratory-scale composting environment. The method is not applicable to the determination of the biodegradability of plastic materials under composting conditions. Further testing is necessary to be able to claim compostability.
- Standard9 pagesEnglish languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
- 24-Aug-2023
- 83.080.01
- ISO/TC 61/SC 14
This document specifies the process references model (PRM) for human-centred design (HCD) according to ISO 9241-220, as well as the process assessment model (PAM) for assessing these processes, based on ISO/IEC 33020 and in accordance with the requirements of ISO/IEC 33004. This HCD PAM contains a set of indicators to be considered while interpreting the intent of the HCD PRM defined in ISO 9241-220. These indicators can also be applied when implementing a process improvement programme post an assessment. NOTE 1 The PRM in this document focuses on assessing HCD processes rather than system life cycle, for example as in ISO/IEC/IEEE 15288, or software life cycle, as in ISO/IEC/IEEE 12207. NOTE 2 If processes beyond the scope of ISO 9241-220 are required, appropriate processes from other PRMs, such as ISO/IEC/IEEE 12207, ISO/IEC/IEEE 15288 or ISO/TS 18152, can be added based on the business needs of the organization. The intended application of this document is computer-based interactive systems. While the processes apply to interactive systems that deliver services, they do not cover the design of those services. The relevant aspects of the processes can also be applied to simple or non-computer-based interactive systems. NOTE 3 HCD concentrates on the human-centred aspects of design and not on other aspects of design, such as mechanical construction, programming or the basic design of services. The process descriptions in this document provide the basis for a rigorous assessment of an enterprise’s capability to carry out human-centred processes in conformity with the ISO/IEC 33004 and ISO/IEC 33020. This document is intended for use by organizations that want to address and improve their treatment of human-centred design of either their internal systems or the products and services they provide, and the procurement of systems and parts of systems. The processes can be applied by small- and medium-sized enterprises as well as by large organizations. NOTE 4 The scope of application of the PAM is the same as that of the PRM, which is described in ISO 9241-220:2019, Clause 1.
- Standard102 pagesEnglish languagesale 15% off
- 24-Aug-2023
- 13.180
- 35.180
- ISO/TC 159/SC 4
This document gives guidance and requirements for the education, examination and evaluation of the inspectors’ and maintenance technicians’ competence concerning public playground and recreational areas. This document describes the knowledge and competence required for each specific task an inspector or technician performs. This document is intended primarily for public playgrounds, but the principles are applicable to other recreational areas. This document does not include benefit/risk assessment methods. This document does not cover the competence of staff conducting product certification. NOTE 1 The different types of inspections covered are: routine visual inspection; operational inspection; annual main inspection; post-installation inspection; post-accident inspection; pre-installation consultation; mid-installation surveillance. NOTE 2 This document can be applicable to: roller-sport infrastructure; multi-sport arenas; outdoor exercise equipment; bouldering walls; portable and permanent socketed goals; parkour facilities; adventure playgrounds; ropes courses; inflatable play equipment.
- Technical specification23 pagesEnglish languagesale 15% off
- Draft22 pagesEnglish languagesale 15% off
- Draft22 pagesEnglish languagesale 15% off
This document defines terms in the field of cables applied in road vehicle general purpose applications, for use in the other parts of the ISO 19642 series.
- Standard27 pagesEnglish languagesale 15% off
- 24-Aug-2023
- 01.040.43
- 43.040.10
- ISO/TC 22/SC 32
This document instructs the manufacturers of tractors and implements how to integrate mechanically and use the HPI. NOTE The terms "tractor" and "implement” are used instead of “supply system” and “consumer system” for better understanding in this part.
- Standard5 pagesEnglish languagesale 15% off
- 24-Aug-2023
- 65.060.10
- ISO/TC 23/SC 19
- Standard1 pageEnglish languagesale 15% off
- 24-Aug-2023
- 35.030
- ISO/IEC JTC 1/SC 27
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.