Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 1: Main characteristics to be included in literature from suppliers and product-marking requirements

This part of ISO 6953 specifies which characteristics of compressed air pressure regulators are to be
included in literature from their suppliers. It also applies to filter-regulators.
This part of ISO 6953 applies to
— manually controlled direct operated types (with or without relieving mechanism),
— manually controlled internal pilot operating types (e.g. nozzle flapper), and
— external pilot operated types.
In addition, it specifies the product marking requirements for pressure regulators and filter-regulators.
This part of ISO 6953 is applicable to compressed air pressure regulators with a rated inlet pressure
of up to 2 500 kPa (25 bar) and an outlet adjustment pressure of up to 1 600 kPa (16 bar); and to
filter-regulators with rated inlet and outlet pressures of up to 1 600 kPa (16 bar), in which the major
contaminants are removed by mechanical means.
NOTE 1 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
The rated pressure should be selected from the preferred pressures listed in ISO 2944.
NOTE 2 The main characteristics to be included in the supplier’s literature related to electrically modulated
pneumatic continuous pressure control valves are specified in ISO 10094-1.

Transmissions pneumatiques - Régulateurs de pression et filtres-régulateurs pour air comprimé - Partie 1: Principales caractéristiques à inclure dans la documentation des fournisseurs et exigences de marquage du produit

L'ISO 6953-1:2015 sp�cifie les caract�ristiques des r�gulateurs de pression pour air comprim� � inclure dans la documentation des fournisseurs. Elle s'applique aussi aux filtres-r�gulateurs.
L'ISO 6953-1:2015 s'applique: aux types � commande directe manuelle (avec ou sans dispositif de mise � l'�chappement); aux types � pilotage interne � commande manuelle (par exemple premier �tage avec m�canisme buse-palette); et aux types � pilotage externe.
En outre, elle sp�cifie les exigences de marquage de produit pour les r�gulateurs de pression et les filtres-r�gulateurs.
L'ISO 6953-1:2015 est applicable aux r�gulateurs de pression pour air comprim� pour une pression de fonctionnement (pression d'alimentation) jusqu'� 2 500 kPa (25 bar) et pour une pression de sortie r�gul�e ajustable jusqu'� 1 600 kPa (16 bar); et aux filtres-r�gulateurs pour une pression de fonctionnement (pression d'alimentation) et pression de sortie r�gul�e jusqu'� 1 600 kPa (16 bar), dans lesquels les impuret�s les plus grandes sont �limin�es par voie m�canique.

Fluidna tehnika - Pnevmatika - Regulatorji tlaka in regulatorji tlaka s filtri - 1. del: Glavne značilnosti, ki morajo biti navedene v dokumentaciji dobaviteljev, in načini označevanja

Ta del standarda ISO 6953 določa lastnosti regulatorjev tlaka, ki morajo biti navedene v dokumentaciji dobaviteljev. Uporablja se tudi za regulatorje s filtri.
Ta del standarda ISO 6953 se uporablja za:
– ročno krmiljene tipe za neposredno upravljanje (s sprostitvenim mehanizmom ali brez njega);
– ročno krmiljene tipe za notranje pilotsko upravljanje (npr. zaklopnica šobe);
– zunanje pilotsko upravljane tipe.
Poleg tega določa zahteve za označevanje proizvodov za regulatorje tlaka in regulatorje s filtri. Ta del standarda ISO 6953 se uporablja za regulatorje tlaka z nazivnim vhodnim tlakom največ 2500 kPa (25 barov) in izhodnim prilagoditvenim tlakom največ 1600 kPa (16 barov) ter za regulatorje s filtri z nazivnim vhodnim in izhodnim tlakom največ 1600 kPa (16 barov), ki omogočajo mehansko odstranjevanje večjih delcev umazanije.
OPOMBA 1: 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
Nazivna vrednost tlaka mora biti izbrana s seznama prednostnih tlačnih vrednosti v standardu ISO 2944.
OPOMBA 2: Glavne lastnosti za vključitev v dokumentacijo dobaviteljev v zvezi z električno moduliranimi pnevmatskimi ventili za neprekinjeno reguliranje tlaka so podane v standardu ISO 10094-1.

General Information

Status
Published
Publication Date
28-Mar-2016
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Mar-2016
Due Date
26-May-2016
Completion Date
29-Mar-2016

Relations

Buy Standard

Standard
ISO 6953-1:2015 - Pneumatic fluid power -- Compressed air pressure regulators and filter-regulators
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 6953-1:2016
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 6953-1:2015 - Transmissions pneumatiques -- Régulateurs de pression et filtres-régulateurs pour air comprimé
French language
12 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6953-1
Third edition
2015-03-01
Pneumatic fluid power — Compressed
air pressure regulators and filter-
regulators —
Part 1:
Main characteristics to be included in
literature from suppliers and product-
marking requirements
Transmissions pneumatiques — Régulateurs de pression et filtres-
régulateurs pour air comprimé —
Partie 1: Principales caractéristiques à inclure dans la documentation
des fournisseurs et exigences de marquage du produit
Reference number
ISO 6953-1:2015(E)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 6953-1:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6953-1:2015(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Technical requirements . 2
4.1 General . 2
4.2 General characteristics . 3
4.2.1 General dimensions . 3
4.2.2 Port forms . 5
4.2.3 Rated pressure . 5
4.2.4 Range of operating temperatures . 5
4.3 Particular requirements . 5
4.3.1 General. 5
4.3.2 Adjustable pressure ranges (outlet regulated pressure) . 5
4.3.3 Flow-pressure characteristics . 6
4.3.4 Pressure regulation characteristic . 7
4.3.5 Pilot pressure/regulated pressure characteristics. 7
4.3.6 Repeatability (optional characteristic) . 9
4.3.7 Resolution in the case of pilot operated regulator with air bleed . 9
4.3.8 Maximum air consumption at null forward flow rate or relief flow rate for pilot
operated regulator with air bleed . 9
4.3.9 Useful retention capacity of the reservoir . 9
4.3.10 Filter-regulator draining devices . 9
4.3.11 Materials of construction. 9
5 Operation and maintenance .10
6 Marking .10
7 Identification statement (Reference to ISO 6953) .10
Annex A (informative) Port forms from ISO 1179-1:1981 .11
Bibliography .12
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6953-1:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT), see the following URL: Foreword — Supplementary information.
The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 5,
Control products and components.
This third edition cancels and replaces the second edition (ISO 6953-1:2000), which has been technically
revised. It also incorporates ISO 6953-1:2000/Cor 1:2006.
ISO 6953 consists of the following parts, under the general title Pneumatic fluid power — Compressed air
pressure regulators and filter-regulators:
— Part 1: Main characteristics to be included in the supplier’s literature and product-marking requirements
— Part 2: Test methods to determine the main characteristics to be included in supplier’s literature
— Part 3: Alternative test methods for measuring the flow-rate characteristics of pressure regulators
iv © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 6953-1:2015(E)

Introduction
In pneumatic fluid power systems, power is transmitted and controlled through a gas under pressure
within a circuit.
When pressure reduction or pressure regulation is required, regulators and filter-regulators are
components designed to maintain the pressure of the gas at an approximately constant level.
It is therefore necessary to know some performance characteristics of these components in order to
determine their suitability for an application.
© ISO 2015 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 6953-1:2015(E)
Pneumatic fluid power — Compressed air pressure
regulators and filter-regulators —
Part 1:
Main characteristics to be included in literature from
suppliers and product-marking requirements
1 Scope
This part of ISO 6953 specifies which characteristics of compressed air pressure regulators are to be
included in literature from their suppliers. It also applies to filter-regulators.
This part of ISO 6953 applies to
— manually controlled direct operated types (with or without relieving mechanism),
— manually controlled internal pilot operating types (e.g. nozzle flapper), and
— external pilot operated types.
In addition, it specifies the product marking requirements for pressure regulators and filter-regulators.
This part of ISO 6953 is applicable to compressed air pressure regulators with a rated inlet pressure
of up to 2 500 kPa (25 bar) and an outlet adjustment pressure of up to 1 600 kPa (16 bar); and to
filter-regulators with rated inlet and outlet pressures of up to 1 600 kPa (16 bar), in which the major
contaminants are removed by mechanical means.
5 2
NOTE 1 1 bar = 0,1 MPa = 10 Pa; 1 MPa = 1 N/mm .
The rated pressure should be selected from the preferred pressures listed in ISO 2944.
NOTE 2 The main characteristics to be included in the supplier’s literature related to electrically modulated
pneumatic continuous pressure control valves are specified in ISO 10094-1.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions,
tolerances and designation
ISO 2944, Fluid power systems and components — Nominal pressures
ISO 5598, Fluid power systems and components — Vocabulary
ISO 5782-2:1997, Pneumatic fluid power — Compressed-air filters — Part 2: Test methods to determine the
main characteristics to be included in supplier’s literature
ISO 6358-1, Pneumatic fluid power — Determination of flow-rate characteristics of components using
compressible fluids — Part 1: General rules and test methods for steady-state flow
ISO 6953-2:2015, Pneumatic fluid power — Compressed air pressure regulators and filter-regulators —
Part 2: Test methods to determine the main characteristics to be included in literature from suppliers
© ISO 2015 – All rights reserved 1

---------------------- Page: 6 ----------------------
ISO 6953-1:2015(E)

ISO 10094-1, Pneumatic fluid power — Electro-pneumatic pressure control valves — Part 1: Main
characteristics to include in the supplier’s literature
ISO 11727, Pneumatic fluid power — Identification of ports and control mechanisms of control valves and
other components
3 Terms and definitions
For the purposes of this part of ISO 6953, the terms and definitions given in ISO 5598, ISO 6358-1,
ISO 10094-1, and the following apply.
3.1
compressed air pressure regulator
component designed to maintain compressed air pressure, approximately constant within an enclosed
circuit despite variation in operating flow rate and inlet pressure
3.2
relieving pressure regulator
pressure regulator equipped with an unloading device that opens if the regulated pressure exceeds the
original setting by a sufficient degree, and exhausts a limited flow rate of air from the outlet circuit to
the atmosphere
3.3
filter-regulator
device that combines the filter and regulator onto one body as a single unit
Note 1 to entry: In such a device, the filter is always on the upstream side of the regulator.
3.4
pilot-operated regulator with air bleed
regulator designed to minimize the variation of regulated pressure from its set point during flow, using
a pilot supply that continuously flows through the pilot chamber and is exhausted
3.5
flow-pressure characteristic curve
graphical representation of the relationship between the regulated pressure and the forward flow rate
or the relief flow rate while the outlet set pressure and the inlet pressure are maintained constant
3.5.1
forward flow/pressure characteristic curve
flow/pressure characteristic curve in accordance with 3.5 only for the forward flow rate
3.5.2
relief flow/pressure characteristic curve
flow/pressure characteristic curve in accordance with 3.5 only for the relief flow rate
3.6
pressure regulation characteristic curve
graphical representation of regulated pressure variation caused by changes in inlet (supply) pressure,
at a constant small air flow rate and low regulated p
...

SLOVENSKI STANDARD
SIST ISO 6953-1:2016
01-maj-2016
1DGRPHãþD
SIST ISO 6953-1:2001
)OXLGQDWHKQLND3QHYPDWLND5HJXODWRUMLWODNDLQUHJXODWRUMLWODNDVILOWULGHO
*ODYQH]QDþLOQRVWLNLPRUDMRELWLQDYHGHQHYGRNXPHQWDFLMLGREDYLWHOMHYLQQDþLQL
R]QDþHYDQMD
Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 1:
Main characteristics to be included in literature from suppliers and product-marking
requirements
Transmissions pneumatiques - Régulateurs de pression et filtres-régulateurs pour air
comprimé - Partie 1: Principales caractéristiques à inclure dans la documentation des
fournisseurs et exigences de marquage du produit
Ta slovenski standard je istoveten z: ISO 6953-1:2015
ICS:
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
23.100.50 Krmilni sestavni deli Control components
SIST ISO 6953-1:2016 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 6953-1:2016

---------------------- Page: 2 ----------------------

SIST ISO 6953-1:2016
INTERNATIONAL ISO
STANDARD 6953-1
Third edition
2015-03-01
Pneumatic fluid power — Compressed
air pressure regulators and filter-
regulators —
Part 1:
Main characteristics to be included in
literature from suppliers and product-
marking requirements
Transmissions pneumatiques — Régulateurs de pression et filtres-
régulateurs pour air comprimé —
Partie 1: Principales caractéristiques à inclure dans la documentation
des fournisseurs et exigences de marquage du produit
Reference number
ISO 6953-1:2015(E)
©
ISO 2015

---------------------- Page: 3 ----------------------

SIST ISO 6953-1:2016
ISO 6953-1:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 6953-1:2016
ISO 6953-1:2015(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Technical requirements . 2
4.1 General . 2
4.2 General characteristics . 3
4.2.1 General dimensions . 3
4.2.2 Port forms . 5
4.2.3 Rated pressure . 5
4.2.4 Range of operating temperatures . 5
4.3 Particular requirements . 5
4.3.1 General. 5
4.3.2 Adjustable pressure ranges (outlet regulated pressure) . 5
4.3.3 Flow-pressure characteristics . 6
4.3.4 Pressure regulation characteristic . 7
4.3.5 Pilot pressure/regulated pressure characteristics. 7
4.3.6 Repeatability (optional characteristic) . 9
4.3.7 Resolution in the case of pilot operated regulator with air bleed . 9
4.3.8 Maximum air consumption at null forward flow rate or relief flow rate for pilot
operated regulator with air bleed . 9
4.3.9 Useful retention capacity of the reservoir . 9
4.3.10 Filter-regulator draining devices . 9
4.3.11 Materials of construction. 9
5 Operation and maintenance .10
6 Marking .10
7 Identification statement (Reference to ISO 6953) .10
Annex A (informative) Port forms from ISO 1179-1:1981 .11
Bibliography .12
© ISO 2015 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 6953-1:2016
ISO 6953-1:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT), see the following URL: Foreword — Supplementary information.
The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 5,
Control products and components.
This third edition cancels and replaces the second edition (ISO 6953-1:2000), which has been technically
revised. It also incorporates ISO 6953-1:2000/Cor 1:2006.
ISO 6953 consists of the following parts, under the general title Pneumatic fluid power — Compressed air
pressure regulators and filter-regulators:
— Part 1: Main characteristics to be included in the supplier’s literature and product-marking requirements
— Part 2: Test methods to determine the main characteristics to be included in supplier’s literature
— Part 3: Alternative test methods for measuring the flow-rate characteristics of pressure regulators
iv © ISO 2015 – All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 6953-1:2016
ISO 6953-1:2015(E)

Introduction
In pneumatic fluid power systems, power is transmitted and controlled through a gas under pressure
within a circuit.
When pressure reduction or pressure regulation is required, regulators and filter-regulators are
components designed to maintain the pressure of the gas at an approximately constant level.
It is therefore necessary to know some performance characteristics of these components in order to
determine their suitability for an application.
© ISO 2015 – All rights reserved v

---------------------- Page: 7 ----------------------

SIST ISO 6953-1:2016

---------------------- Page: 8 ----------------------

SIST ISO 6953-1:2016
INTERNATIONAL STANDARD ISO 6953-1:2015(E)
Pneumatic fluid power — Compressed air pressure
regulators and filter-regulators —
Part 1:
Main characteristics to be included in literature from
suppliers and product-marking requirements
1 Scope
This part of ISO 6953 specifies which characteristics of compressed air pressure regulators are to be
included in literature from their suppliers. It also applies to filter-regulators.
This part of ISO 6953 applies to
— manually controlled direct operated types (with or without relieving mechanism),
— manually controlled internal pilot operating types (e.g. nozzle flapper), and
— external pilot operated types.
In addition, it specifies the product marking requirements for pressure regulators and filter-regulators.
This part of ISO 6953 is applicable to compressed air pressure regulators with a rated inlet pressure
of up to 2 500 kPa (25 bar) and an outlet adjustment pressure of up to 1 600 kPa (16 bar); and to
filter-regulators with rated inlet and outlet pressures of up to 1 600 kPa (16 bar), in which the major
contaminants are removed by mechanical means.
5 2
NOTE 1 1 bar = 0,1 MPa = 10 Pa; 1 MPa = 1 N/mm .
The rated pressure should be selected from the preferred pressures listed in ISO 2944.
NOTE 2 The main characteristics to be included in the supplier’s literature related to electrically modulated
pneumatic continuous pressure control valves are specified in ISO 10094-1.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions,
tolerances and designation
ISO 2944, Fluid power systems and components — Nominal pressures
ISO 5598, Fluid power systems and components — Vocabulary
ISO 5782-2:1997, Pneumatic fluid power — Compressed-air filters — Part 2: Test methods to determine the
main characteristics to be included in supplier’s literature
ISO 6358-1, Pneumatic fluid power — Determination of flow-rate characteristics of components using
compressible fluids — Part 1: General rules and test methods for steady-state flow
ISO 6953-2:2015, Pneumatic fluid power — Compressed air pressure regulators and filter-regulators —
Part 2: Test methods to determine the main characteristics to be included in literature from suppliers
© ISO 2015 – All rights reserved 1

---------------------- Page: 9 ----------------------

SIST ISO 6953-1:2016
ISO 6953-1:2015(E)

ISO 10094-1, Pneumatic fluid power — Electro-pneumatic pressure control valves — Part 1: Main
characteristics to include in the supplier’s literature
ISO 11727, Pneumatic fluid power — Identification of ports and control mechanisms of control valves and
other components
3 Terms and definitions
For the purposes of this part of ISO 6953, the terms and definitions given in ISO 5598, ISO 6358-1,
ISO 10094-1, and the following apply.
3.1
compressed air pressure regulator
component designed to maintain compressed air pressure, approximately constant within an enclosed
circuit despite variation in operating flow rate and inlet pressure
3.2
relieving pressure regulator
pressure regulator equipped with an unloading device that opens if the regulated pressure exceeds the
original setting by a sufficient degree, and exhausts a limited flow rate of air from the outlet circuit to
the atmosphere
3.3
filter-regulator
device that combines the filter and regulator onto one body as a single unit
Note 1 to entry: In such a device, the filter is always on the upstream side of the regulator.
3.4
pilot-operated regulator with air bleed
regulator designed to minimize the variation of regulated pressure from its set point during flow, using
a pilot supply that continuously flows through the pilot chamber and is exhausted
3.5
flow-pressure characteristic curve
graphical representation of the relationshi
...

NORME ISO
INTERNATIONALE 6953-1
Troisième édition
2015-03-01
Transmissions pneumatiques —
Régulateurs de pression et filtres-
régulateurs pour air comprimé —
Partie 1:
Principales caractéristiques à
inclure dans la documentation
des fournisseurs et exigences de
marquage du produit
Pneumatic fluid power — Compressed air pressure regulators and
filter-regulators —
Part 1: Main characteristics to be included in literature from suppliers
and product-marking requirements
Numéro de référence
ISO 6953-1:2015(F)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 6953-1:2015(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2015
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2015 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 6953-1:2015(F)

Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Exigences techniques . 3
4.1 Généralités . 3
4.2 Caractéristiques générales. 3
4.2.1 Dimensions générales . 3
4.2.2 Formes des orifices . 5
4.2.3 Pression de fonctionnement . 5
4.2.4 Plage de températures d’utilisation . 5
4.3 Exigences particulières . 5
4.3.1 Généralités . 5
4.3.2 Etendues des valeurs de consigne de pressions(pression de sortie régulée) . 5
4.3.3 Caractéristiques de débit/pression . 6
4.3.4 Caractéristiques de régulation de pression . 7
4.3.5 Caractéristiques de pression de pilotage/pression régulée . 7
4.3.6 Répétabilité (caractéristique facultative) . 9
4.3.7 Résolution pour les régulateurs pilotés . 9
4.3.8 Consommation maximale d’air à débit d’alimentation et d’échappement
nuls pour les régulateurs pilotés . 9
4.3.9 Capacité utile de rétention de la cuve . 9
4.3.10 Dispositifs de purge du filtre-régulateur . 9
4.3.11 Matériaux de construction .10
5 Mise en service et entretien .10
6 Marquage .10
7 Phrase d’identification (référence à l’ISO 6953) .10
Annexe A (informative) Formes des orifices cités dans l’ISO 1179-1:1981 .11
Bibliographie .12
© ISO 2015 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 6953-1:2015(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui concerne
la normalisation électrotechnique.
La procédure utilisée pour développer ce document et ceux destinés à son maintien futur sont décrits
dans les Directives ISO/IEC, Partie 1. Les différents critères d’approbations que les différents types
de documents ISO nécessitent devraient notamment être notés. Le présent document a été rédigé
conformément aux règles éditoriales des Directives ISO/IEC, Partie 2 (voir www.iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence.
Toute appellation commerciale utilisée dans le présent document est une information donnée pour des
raisons de commodités et ne reflète pas une approbation.
Pour une explication de la signification des termes et expressions spécifiques liés à l’évaluation de la
conformité utilisés par l’ISO, ainsi que pour des informations concernant l’adhésion de l’ISO aux principes
de l’Organisation mondiale du Commerce (OMC) dans l’accord Obstacles techniques au commerce (OTC),
voir l’URL suivant: Avant-propos – Informations supplémentaires.
Le comité chargé de l’élaboration du présent document est l’ISO/TC 131, Transmissions hydrauliques et
pneumatiques, sous-comité SC 5, Appareils de régulation et de distribution et leurs composants.
Cette troisième édition annule et remplace la deuxième édition (ISO 6953-1:2000), qui a fait l’objet d’une
révision technique. Elle incorpore également l’ISO 6953-1:2000/Cor 1:2006.
L’ISO 6953 comprend les parties suivantes, présentées sous le titre général Transmissions pneumatiques —
Régulateurs de pression et filtres-régulateurs pour air comprimé:
— Partie 1: Principales caractéristiques à inclure dans la documentation des fournisseurs et exigences de
marquage du produit
— Partie 2: Méthodes d’essai pour déterminer les principales caractéristiques à inclure dans la
documentation des fournisseurs
— Partie 3: Méthodes d’essai alternatives pour mesurer les caractéristiques de débit des régulateurs de pression
iv © ISO 2015 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO 6953-1:2015(F)

Introduction
Dans les systèmes de transmissions pneumatiques, l’énergie est transmise et contrôlée par l’intermédiaire
d’un gaz sous pression circulant dans un circuit.
Lorsqu’une réduction ou une régulation de la pression est nécessaire, les régulateurs de pression et les
filtres-régulateurs sont conçus pour maintenir approximativement constante la pression du gaz.
Il est donc nécessaire de connaître certaines caractéristiques de performance de ces composants pour
déterminer leur aptitude à l’emploi pour une application donnée.
© ISO 2015 – Tous droits réservés v

---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 6953-1:2015(F)
Transmissions pneumatiques — Régulateurs de pression
et filtres-régulateurs pour air comprimé —
Partie 1:
Principales caractéristiques à inclure dans la documentation
des fournisseurs et exigences de marquage du produit
1 Domaine d’application
La présente partie de l’ISO 6953 spécifie les caractéristiques des régulateurs de pression pour air
comprimé à inclure dans la documentation des fournisseurs. Elle s’applique aussi aux filtres-régulateurs.
La présente partie de l’ISO 6953 s’applique
— aux types à commande directe manuelle (avec ou sans dispositif de mise à l’échappement),
— aux types à pilotage interne à commande manuelle (par exemple premier étage avec mécanisme
buse-palette), et
— aux types à pilotage externe.
En outre, elle spécifie les exigences de marquage de produit pour les régulateurs de pression et les
filtres-régulateurs.
La présente partie de l’ISO 6953 est applicable aux régulateurs de pression pour air comprimé pour une
pression de fonctionnement (pression d’alimentation) jusqu’à 2 500 kPa (25 bar) et pour une pression
de sortie régulée ajustable jusqu’à 1 600 kPa (16 bar); et aux filtres-régulateurs pour une pression de
fonctionnement (pression d’alimentation) et pression de sortie régulée jusqu’à 1 600 kPa (16 bar), dans
lesquels les impuretés les plus grandes sont éliminées par voie mécanique.
5 2
NOTE 1 1 bar = 0,1 MPa = 10 Pa; 1 MPa = 1 N/mm .
Il convient de choisir la pression de fonctionnement parmi les pressions préférentielles listées dans l’ISO 2944.
NOTE 2 Les principales caractéristiques à inclure dans la documentation des fournisseurs pour les appareils
électropneumatiques de distribution à commande continue de pression sont spécifiées dans l’ISO 10094-1.
2 Références normatives
Les documents suivants, en tout ou partie, sont référencés de manière normative dans le présent
document et sont indispensables pour son application. Pour les références datées, seule l’édition citée
s’applique. Pour les références non datées, la dernière édition du document de référence s’applique (y
compris les éventuels amendements).
ISO 7-1:1994, Filetages de tuyauterie pour raccordement avec étanchéité dans le filet — Partie 1: Dimensions,
tolérances et désignation
ISO 2944, Transmissions hydrauliques et pneumatiques — Pressions nominales
ISO 5598, Transmissions hydrauliques et pneumatiques — Vocabulaire
ISO 5782-2:1997, Transmissions pneumatiques — Filtres pour air comprimé — Partie 2: Méthodes d’essai
pour déterminer les principales caractéristiques à inclure dans la documentation des fournisseurs
© ISO 2015 – Tous droits réservés 1

---------------------- Page: 6 ----------------------
ISO 6953-1:2015(F)

ISO 6358-1, Transmissions pneumatiques — Détermination des caractéristiques de débit des composants
traversés par un fluide compressible — Partie 1: Règles générales et méthodes d’essai en régime stationnaire
ISO 6953-2:2015, Transmissions pneumatiques — Régulateurs de pression et filtre-régulateurs pour air
comprimé — Partie 2: Méthodes d’essai pour déterminer les principales caractéristiques à inclure dans la
documentation des fournisseurs
ISO 10094-1, Transmissions pneumatiques — Appareils électropneumatiques de distribution à commande
continue de pression — Partie 1: Principales caractéristiques à inclure dans la documentation des fournisseurs
ISO 11727, Transmissions pneumatiques — Identification des orifices et des mécanismes de commande des
distributeurs de commande et autres composants
3 Termes et définitions
Pour les besoins de la présente partie de l’ISO 6953, les termes et définitions donnés dans l’ISO 5598,
l’ISO 6358-1, l’ISO 10094-1 ainsi que les suivants s’appliquent.
3.1
régulateur de pression pour air comprimé
composant conçu pour maintenir sensiblement constante la pression d’air comprimé dans un circuit
donné quelles que soient les variations du débit d’utilisation et de la pression d’alimentation.
3.2
régulateur de pression avec dispositif de mise à l’échappement
régulateur de pression équipé d’un dispositif de mise à l’échappement qui s’ouvre si la pression régulée
devient supérieure au réglage original, et qui laisse s’échapper un débit limité d’air du circuit de pression
régulée vers l’atmosphère
3.3
filtre-régulateur
appareil qui combine un filtre et un régulateur dans un corps formant ainsi une unité unique
Note 1 à l’article: Dans un tel appareil, le filtre est toujours en amont du régulateur.
3.4
régulateur piloté
régulateur conçu pour réduire le plus possible les variations de la pression régulée par rapport à sa
valeur de consigne quel que soit le débit, grâce à un premier étage constitué d’un régulateur avec évent.
3.5
courbe caractéristique débit/pression
représentation graphique de la relation entre la pression régulée et le débit d’alimentation ou le débit
d’échappement, alors que la consigne de pression et la pression d’alimentation sont maintenues constantes
3.5.1
courbe caractéristique de débit d’alimentation /pression
courbe caractéristique de débit d’alimentation/pression conformément au 3.5 pour le débit
d’alimentation uniquement.
3.5.2
courbe caractéristique de débit d’échappement /pression
courbe caractéristique de débit d’échappement/pression conformément au 3.5 pour le débit
d’échappement uniquement.
3.6
courbe caractéristique de régulation de pression
représentation graphique de la variation de la pression régulée sous l’effet d’une variation de la pression
d’alimentation, mesurée pour un débit d’air faible et constant et pour une pression régulée peu élevée
2 © ISO 2015 – Tous droits réservés

---------------------- Page: 7 ----------------------
ISO 6953-1:2015(F)

4 Exigences techniques
4.1 Généralités
La documentation concernant les régulateurs de pression et les filtres-régulateurs pour air comprimé
doit inclure les caractéristiques données en 4.2 et 4.3.
4.2 Caractéristiques générales
4.2.1 Dimensions générales
Les dimensions représentées sur la Figure 1 doivent être indiquées en millimètres. Pour les orifices, voir
4.2.2.
© ISO 2015 – Tous droits réservés 3

-------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.