SIST EN ISO 21487:2013
(Main)Small craft - Permanently installed petrol and diesel fuel tanks (ISO 21487:2012)
Small craft - Permanently installed petrol and diesel fuel tanks (ISO 21487:2012)
This International Standard establishes requirements for design and test of petrol and diesel fuel tanks for internal combustion engines that are intended to be permanently installed in small craft of up to 24 m length of hull. For installation requirements, ISO 10088 applies.
Kleine Wasserfahrzeuge - Fest eingebaute Ottokraftstoff- und Dieselkraftstofftanks (ISO 21487:2012)
Diese Internationale Norm legt Anforderungen an die Konstruktion und die Prüfung von fest eingebauten
Ottokraftstoff- und Dieselkraftstofftanks für Verbrennungsmotoren auf kleinen Wasserfahrzeugen mit einer
Rumpflänge bis 24 m fest.
Für Anforderungen an die Installation ist ISO 10088 anzuwenden.
Petits navires - Réservoirs à carburant à essence et diesel installés à demeure (ISO 21487:2012)
L'ISO 21487:2012 établit des exigences sur la conception et les essais des réservoirs à carburant essence et diesel pour les moteurs à combustion interne et destinés à être installés à demeure sur des bateaux d'une longueur de coque inférieure ou égale à 24 m.
L'ISO 10088 s'applique pour ce qui concerne les exigences d'installation.
Mala plovila - Trajno vgrajeni rezervoarji za bencinsko in dizelsko gorivo (ISO 21487:2012)
Mednarodni standard določa zahteve za načrtovanje in preskušanje rezervoarjev za bencinsko in dizelsko gorivo za motorje z notranjim zgorevanjem, ki so namenjeni trajni vgradnji v mala plovila z dolžino trupa do 24 m. Zahteve glede namestitve so določene v standardu ISO 10088.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 21487:2013
01-maj-2013
1DGRPHãþD
SIST EN ISO 21487:2007
SIST EN ISO 21487:2007/AC:2009
Mala plovila - Trajno vgrajeni rezervoarji za bencinsko in dizelsko gorivo (ISO
21487:2012)
Small craft - Permanently installed petrol and diesel fuel tanks (ISO 21487:2012)
Kleine Wasserfahrzeuge - Fest eingebaute Ottokraftstoff- und Dieselkraftstofftanks (ISO
21487:2012)
Petits navires - Réservoirs à carburant à essence et diesel installés à demeure (ISO
21487:2012)
Ta slovenski standard je istoveten z: EN ISO 21487:2012
ICS:
47.020.20 Ladijski motorji Marine engines and
propulsion systems
47.080 ýROQL Small craft
SIST EN ISO 21487:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 21487:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 21487:2013
EUROPEAN STANDARD
EN ISO 21487
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2012
ICS 47.080 Supersedes EN ISO 21487:2006
English Version
Small craft - Permanently installed petrol and diesel fuel tanks
(ISO 21487:2012)
Petits navires - Réservoirs à carburant à essence et diesel Kleine Wasserfahrzeuge - Fest eingebaute Ottokraftstoff-
installés à demeure (ISO 21487:2012) und Dieselkraftstofftanks (ISO 21487:2012)
This European Standard was approved by CEN on 14 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21487:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 21487:2013
EN ISO 21487:2012 (E)
Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive 2003/44/EC .4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 21487:2013
EN ISO 21487:2012 (E)
Foreword
This document (EN ISO 21487:2012) has been prepared by Technical Committee ISO/TC 188 "Small craft".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the
latest by May 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 21487:2006.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 21487:2012 has been approved by CEN as a EN ISO 21487:2012 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 21487:2013
EN ISO 21487:2012 (E)
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive
2003/44/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission to
provide one means of conforming to Essential Requirements of the New Approach Directive 94/25/EC as
amended by Directive 2003/44/EC.
Once this European Standard is cited in the Official Journal of the European Union under that Directive and
has been implemented as a national standard in at least one member state, compliance with the normative
clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a
presumption of conformity with the relevant Essential Requirements of that Directive and associated EFTA
regulations.
Table ZA.1: Correspondence between this European Standard and Directive 94/25/EC as amended by
Directive 2003/44/EC
Clauses/sub-clauses of this Corresponding annexes/paragraphs of Comments
standard Directive 94/25/EC as amended by
Directive 2003/44/EC
All clauses Annex I, Clause 5.2.2, Fuel tanks
Annex II, Components, 4, Fuel tanks
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 21487:2013
INTERNATIONAL ISO
STANDARD 21487
Second edition
2012-11-15
Small craft — Permanently installed
petrol and diesel fuel tanks
Petits navires — Réservoirs à carburant à essence et diesel installés à
demeure
Reference number
ISO 21487:2012(E)
©
ISO 2012
---------------------- Page: 7 ----------------------
SIST EN ISO 21487:2013
ISO 21487:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 21487:2013
ISO 21487:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General properties . 2
4.1 Resistance to liquids in contact . 2
4.2 Copper-based alloys . 2
4.3 Provisions to tanks . 2
4.4 Installation of non-integral tanks . 3
5 Petrol fuel tanks: design and tests . 3
5.1 Design . 3
5.2 Tests to be performed . 3
6 Diesel fuel tanks: design and tests . 4
6.1 Design . 4
6.2 Tests to be performed . 4
7 Tests . 4
7.1 General . 4
7.2 Hydraulic pressure test . 4
7.3 Pressure-impulse type test for petrol fuel tanks . 6
7.4 General fire-resistance test of non-metallic fuel tanks . 6
7.5 As-installed fire-resistance test of non-metallic fuel tanks . 7
8 Marking . 8
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 21487:2013
ISO 21487:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 21487 was prepared by Technical Committee ISO/TC 188, Small craft.
This second edition cancels and replaces the first edition (ISO 21487:2006), which has been technically revised.
It also incorporates the Technical Corrigendum ISO 21487:2006/Cor.1:2008. The main changes from the first
edition are the following:
— diesel tanks shall be equipped with inspection hatch(es) for cleaning and inspection (4.3.10);
— metallic tanks may be static pressure tested as an alternative to the pressure-impulse test (5.2.2);
— non-metallic, non-integral tanks, if installed in an engine compartment, shall be fire tested (6.2.3);
— non-metallic tanks shall be marked with the maximum temperature to which the tank may be exposed (Clause 8).
iv © ISO 2012 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 21487:2013
INTERNATIONAL STANDARD ISO 21487:2012(E)
Small craft — Permanently installed petrol and diesel fuel tanks
1 Scope
This International Standard establishes requirements for design and test of petrol and diesel fuel tanks for internal
combustion engines that are intended to be permanently installed in small craft of up to 24 m length of hull.
For installation requirements, ISO 10088 applies.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
ISO 10088, Small craft — Permanently installed fuel systems
ISO 11192, Small craft — Graphical symbols
ISO 12215-5, Small craft — Hull construction and scantlings — Part 5: Design pressures for monohulls, design
stresses, scantlings determination
ISO 12215-6, Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details
ISO 5817, Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) —
Quality levels for imperfections
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
petrol
hydrocarbon fuel or blend of hydrocarbon fuel and denatured ethanol which is liquid at atmospheric pressure
and is used in spark ignition engines
3.2
diesel
hydrocarbon fuel, biofuel or blend of these which is liquid at atmospheric pressure and is used in compression
ignition engines
3.3
spark ignition engine
engine in which an electrical spark is produced to ignite the fuel/air mixture
3.4
compression ignition engine
engine in which ignition is obtained by means of compressing the fuel/air mixture
3.5
permanently installed
securely fastened so that tools need to be used for removal
© ISO 2012 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 21487:2013
ISO 21487:2012(E)
3.6
integral tank
tank which forms part of the structure of the craft
4 General properties
4.1 Resistance to liquids in contact
4.1.1 All seals such as gaskets, o-rings and joint-rings shall be of non-wicking, i.e. non-fuel absorbent, material.
4.1.2 All materials used shall be resistant to deterioration by the fuel for which the system is designed and
to other liquids or compounds with which the material can come in contact as installed under normal operating
conditions, e.g. grease, lubricating oil, bilge solvents and sea water.
4.2 Copper-base
...
SLOVENSKI STANDARD
oSIST prEN ISO 21487:2011
01-junij-2011
Mala plovila - Trajno vgrajeni rezervoarji za bencinsko in dizelsko gorivo (ISO/DIS
21487:2011)
Small craft - Permanently installed petrol and diesel fuel tanks (ISO/DIS 21487:2011)
Kleine Wasserfahrzeuge - Fest eingebaute Ottokraftstoff- und Dieselkraftstofftanks
(ISO/DIS 21487:2011)
Petits navires - Réservoirs à carburant à essence et diesel installés à demeure (ISO/DIS
21487:2011)
Ta slovenski standard je istoveten z: prEN ISO 21487
ICS:
47.020.20 Ladijski motorji Marine engines and
propulsion systems
47.080 ýROQL Small craft
oSIST prEN ISO 21487:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 21487:2011
---------------------- Page: 2 ----------------------
oSIST prEN ISO 21487:2011
EUROPEAN STANDARD
DRAFT
prEN ISO 21487
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2011
ICS 47.080 Will supersede EN ISO 21487:2006
English Version
Small craft - Permanently installed petrol and diesel fuel tanks
(ISO/DIS 21487:2011)
Petits navires - Réservoirs à carburant à essence et diesel Kleine Wasserfahrzeuge - Fest eingebaute Ottokraftstoff-
installés à demeure (ISO/DIS 21487:2011) und Dieselkraftstofftanks (ISO/DIS 21487:2011)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/SS T01.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 21487:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 21487:2011
prEN ISO 21487:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 21487:2011
prEN ISO 21487:2011 (E)
Foreword
This document (prEN ISO 21487:2011) has been prepared by Technical Committee ISO/TC 188 "Small craft".
This document is currently submitted to the parallel Enquiry.
This document will supersede EN ISO 21487:2006, EN ISO 21487:2006/AC:2009.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this
document.
Endorsement notice
The text of ISO/DIS 21487:2011 has been approved by CEN as a prEN ISO 21487:2011 without any
modification.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 21487:2011
---------------------- Page: 6 ----------------------
oSIST prEN ISO 21487:2011
DRAFT INTERNATIONAL STANDARD ISO/DIS 21487
ISO/TC 188 Secretariat: SIS
Voting begins on Voting terminates on
2011-03-24 2011-08-24
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Small craft — Permanently installed petrol and diesel fuel tanks
Petits navires — Réservoirs à carburant à essence et diesel installés à demeure
[Revision of first edition (ISO 21487:2006) and ISO 21487:2006/Cor.1:2008]
ICS 47.080
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME
STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
© International Organization for Standardization, 2011
---------------------- Page: 7 ----------------------
oSIST prEN ISO 21487:2011
ISO/DIS 21487
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 21487:2011
ISO/DIS 21487
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 General properties.2
4.1 Resistance to liquids in contact .2
4.2 Copper-based alloys .2
4.3 Provisions to tanks .2
4.4 Petrol fuel tanks.3
4.5 Diesel fuel tanks .3
4.6 Installation of non-integral tanks.3
5 Petrol fuel tanks: design and tests.4
5.1 Design.4
5.2 Tests to be performed.4
6 Diesel fuel tanks: design and tests .4
6.1 Design.4
6.2 Tests to be performed.5
7 Tests .5
7.1 Hydraulic pressure test.5
7.2 Pressure-impulse type test for petrol fuel tanks.6
7.3 General fire-resistance test of non-metallic petrol fuel tanks .6
7.4 As-installed fire-resistance test of non-metallic petrol fuel tanks .8
8 Marking.8
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
oSIST prEN ISO 21487:2011
ISO/DIS 21487
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 21487 was prepared by Technical Committee ISO/TC 188, Small craft.
This second edition cancels and replaces the first edition (EN ISO 21487:2006), which has been technically
revised.
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
oSIST prEN ISO 21487:2011
DRAFT INTERNATIONAL STANDARD ISO/DIS 21487
Small craft — Permanently installed petrol and diesel fuel tanks
1 Scope
This International Standard establishes requirements for design and test of petrol and diesel fuel tanks for
internal combustion engines that are intended to be permanently installed in small craft of up to 24 m length of
hull.
For installation requirements, ISO 10088 applies.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1817:2005, Rubber, vulcanized — Determination of the effect of liquids
ISO 10088:2001, Small craft — Permanently installed fuel systems and fixed fuel tanks
ISO 11192:2005, Small craft — Graphical symbols
ISO 12215-5, Small craft — Hull construction and scantlings — Part 5: Design pressures for monohulls,
1)
design stresses, scantlings determination
ISO 5817:2003, Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding
excluded) — Quality levels for imperfections
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
petrol
hydrocarbon fuel or blend of hydrocarbon fuel and denatured ethanol which is liquid at atmospheric pressure
and is used in spark ignition engines
3.2
diesel
hydrocarbon fuel or bio fuel or blend of those which is liquid at atmospheric pressure and is used in
compression ignition engines
© ISO 2011 – All rights reserved 1
---------------------- Page: 11 ----------------------
oSIST prEN ISO 21487:2011
ISO/DIS 21487
3.3
spark ignition engine
engine in which an electrical spark is produced to ignite the fuel/air mixture
3.4
compression ignition engine
engine in which ignition is obtained by means of compressing the fuel/air mixture
3.5
permanently installed
securely fastened so that tools need to be used for removal
3.6
integral tank
tank which form part of the structure of craft
4 General properties
4.1 Resistance to liquids in contact
4.1.1 All seals such as gaskets, o-rings and joint-rings shall be of non-wicking, i.e. non-fuel absorbent,
material.
4.1.2 All materials used shall be resistant to deterioration by the fuel for which the system is designed and
to other liquids or compounds with which the material can come in contact as installed under normal operating
conditions, e.g. grease, lubricating oil, bilge solvents and sea water.
4.2 Copper-based alloys
Copper-based alloys for fittings are acceptable for direct coupling with all tank materials specified in Table 1,
except aluminium. Copper-based alloy fittings are allowed for aluminium tanks only if a galvanic barrier is
arranged between fitting and tank.
4.3 Provisions to tanks
4.3.1 Provisions shall be made to enable the fuel level or quantity in the tank to be determined.
4.3.2 Metal tanks shall be designed or installed so that no exterior surface will trap water.
4.3.3 Rigid fuel suction tubes and fill pipes which extend near the tank bottom shall have sufficient
clearance to prevent contact with the bottom during normal operation of the craft.
4.3.4 All non-integral tank supports, chocks or hangers shall either be separated from the su
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.