SIST EN ISO 11296-1:2011
(Main)Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General (ISO 11296-1:2009)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General (ISO 11296-1:2009)
This part of ISO 11296 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground non-pressure drainage and sewerage networks, which are operated as gravity systems and subjected to a maximum surcharge pressure of 0,5 bar1). It is applicable to pipes and fittings as manufactured, as well as to the installed plastics lining system; it is not applicable to the existing pipeline or any annular filler.
This part of ISO 11296 establishes the general requirements common to all relevant renovation techniques (see 3.1.2).
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 1: Allgemeines (ISO 11296-1:2009)
Dieser Teil von ISO 11296 legt die Anforderungen und Prüfverfahren für Kunststoff-Rohrleitungssysteme fest, die für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen verwendet werden, die als Frei-spiegel¬leitungen betrieben und bis zu einem maximalen Betriebsüberdruck von 0,5 bar ) belastet werden. Sie gilt sowohl für vorgefertigte Rohre und Formstücke als auch für das eingebaute Kunststoff-Lining-System. Diese Norm gilt nicht für bestehende Rohrleitungen und nicht für Ringraumverfüllungen.
Dieser Teil von ISO 11296 legt die allgemeinen Anforderungen für alle Renovierungstechniken fest (siehe 3.1.2).
Systèmes de canalisations en matières plastiques pour la rénovation des réseaux d'assainissement gravitaires enterrés - Partie 1: Généralités (ISO 11296-1:2009)
L'ISO 11296-1:2009 spécifie les exigences et les méthodes d'essai pour les systèmes de canalisations en plastique destinés à être utilisés pour la rénovation des réseaux d'assainissement enterrés sans pression, qui fonctionnent comme des systèmes sans pression et pouvant faire l'objet d'une mise en charge maximale de 0,5 bar. Elle s'applique aux tubes et raccords tels que fabriqués, de même qu'au système de rénovation en plastique installé. Elle ne s'applique pas à la canalisation existante ni à tout matériau de remplissage annulaire.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 1. del: Splošno (ISO 11296-1:2009)
Ta del ISO 11296 določa zahteve in preskusne metode za polimerne cevne sisteme, ki se uporabljajo za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino), ki delujejo kot težnostni sistemi in zanje velja najvišji dodatni tlak 0,5 bar. Velja za pipe in fitinge, kot so izdelani, in za vgrajeni plastomerni sistem oblaganja; ne velja za obstoječe cevovode ali obročasta polnila.
Ta del ISO 11296 vzpostavlja splošne zahteve, skupne za vse pomembne obnovitvene tehnike (glej 3.1.2).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11296-1:2011
01-december-2011
1DGRPHãþD
SIST EN 13566-1:2003
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za
odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 1.
del: Splošno (ISO 11296-1:2009)
Plastics piping systems for renovation of underground non-pressure drainage and
sewerage networks - Part 1: General (ISO 11296-1:2009)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen
Entwässerungsnetzen (Freispiegelleitungen) - Teil 1: Allgemeines (ISO 11296-1:2009)
Systèmes de canalisations en matières plastiques pour la rénovation des réseaux
d'assainissement gravitaires enterrés - Partie 1: Généralités (ISO 11296-1:2009)
Ta slovenski standard je istoveten z: EN ISO 11296-1:2011
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN ISO 11296-1:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11296-1:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 11296-1:2011
EUROPEAN STANDARD
EN ISO 11296-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.20; 23.040.45; 93.030; 91.140.80 Supersedes EN 13566-1:2002
English Version
Plastics piping systems for renovation of underground non-
pressure drainage and sewerage networks - Part 1: General
(ISO 11296-1:2009)
Systèmes de canalisations en plastique pour la rénovation Kunststoff-Rohrleitungssysteme für die Renovierung von
des réseaux d'assainissement enterrés sans pression - erdverlegten drucklosen Entwässerungsnetzen
Partie 1: Généralités (ISO 11296-1:2009) (Freispiegelleitungen) - Teil 1: Allgemeines (ISO 11296-
1:2009)
This European Standard was approved by CEN on 8 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11296-1:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11296-1:2011
EN ISO 11296-1:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11296-1:2011
EN ISO 11296-1:2011 (E)
Foreword
The text of ISO 11296-1:2009 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings
and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 11296-1:2011 by Technical Committee CEN/TC 155 “Plastics piping systems and
ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13566-1:2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11296-1:2009 has been approved by CEN as a EN ISO 11296-1:2011 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11296-1:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 11296-1:2011
INTERNATIONAL ISO
STANDARD 11296-1
First edition
2009-11-01
Plastics piping systems for renovation
of underground non-pressure drainage
and sewerage networks —
Part 1:
General
Systèmes de canalisations en matières plastiques pour la rénovation
des réseaux d'assainissement gravitaires enterrés —
Partie 1: Généralités
Reference number
ISO 11296-1:2009(E)
©
ISO 2009
---------------------- Page: 7 ----------------------
SIST EN ISO 11296-1:2011
ISO 11296-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11296-1:2011
ISO 11296-1:2009(E)
Contents Page
Foreword .v
Introduction.vi
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
3.1 General terms .1
3.2 Techniques.3
3.3 Characteristics.4
3.4 Origin of materials.5
3.5 Product stages.6
4 Symbols and abbreviated terms .6
4.1 Symbols.6
4.2 Abbreviated terms .6
5 Pipes at the “M” stage .7
5.1 Materials .7
5.2 General characteristics.7
5.3 Material characteristics.7
5.4 Geometric characteristics .7
5.5 Mechanical characteristics.7
5.6 Physical characteristics.7
5.7 Jointing.7
5.8 Marking.7
6 Fittings at the “M” stage.8
6.1 Materials .8
6.2 General characteristics.8
6.3 Material characteristics.8
6.4 Geometric characteristics .8
6.5 Mechanical characteristics.8
6.6 Physical characteristics.8
6.7 Jointing.8
6.8 Marking.8
7 Ancillary components.9
8 Fitness for purpose of the installed lining system at the “I” stage .9
8.1 Materials .9
8.2 General characteristics.9
8.3 Material characteristics.9
8.4 Geometric characteristics .9
8.5 Mechanical characteristics.10
8.6 Physical characteristics.10
8.7 Additional characteristics.10
8.8 Sampling.10
9 Installation practice.10
9.1 Preparatory work .10
9.2 Storage, handling and transport of pipe and fittings .10
9.3 Equipment .10
9.4 Installation.11
9.5 Process-related inspection and testing .12
© ISO 2009 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11296-1:2011
ISO 11296-1:2009(E)
9.6 Lining termination.12
9.7 Reconnection to existing manholes and laterals .12
9.8 Final inspection and testing .12
9.9 Documentation.12
Bibliography .13
iv © ISO 2009 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11296-1:2011
ISO 11296-1:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11296-1 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids.
ISO 11296 consists of the following parts, under the general title Plastics piping systems for renovation of
underground non-pressure drainage and sewerage networks:
⎯ Part 1: General
⎯ Part 3: Lining with close-fit pipes
⎯ Part 4: Lining with cured-in-place pipes
Lining with continuous pipes is to form the subject of a part 2, lining with discrete pipes is to form the subject
of a part 5 and lining with spirally-wound pipes is to form the subject of a part 7.
© ISO 2009 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 11296-1:2011
ISO 11296-1:2009(E)
Introduction
The System Standard, of which this is part 1, specifies the requirements for plastics piping systems of various
materials used for the renovation of existing pipelines in a specified application area. System Standards for
renovation specify procedures for the following applications:
⎯ plastics piping systems for renovation of underground non-pressure drainage and sewerage networks;
⎯ plastics piping systems for renovation of underground drainage and sewerage networks under pressure;
⎯ plastics piping systems for renovation of underground water supply networks;
⎯ plastics piping systems for renovation of underground gas supply networks.
These System Standards are distinguished from those for conventionally installed plastics piping systems
because they set requirements for certain characteristics in the as-installed condition, after site processing.
This is in addition to specifying requirements for system components, as manufactured.
Each of the System Standards comprises a part 1 (general) and all applicable renovation technique family-
related parts from the following:
⎯ part 2: lining with continuous pipes;
⎯ part 3: lining with close-fit pipes;
⎯ part 4: lining with cured-in-place pipes;
⎯ part 5: lining with discrete pipes;
⎯ part 7: lining with spirally-wound pipes.
The requirements for any given renovation technique family are given in part 1, applied in conjunction with the
other relevant part. For example, parts 1 and 2 specify the requirements relating to lining with continuous
pipes. For complementary information, see ISO 11295. Not all technique families are applicable to every area
of application and this is reflected in the part numbers included in each System Standard.
A consistent structure of clause headings has been adopted for all parts to facilitate direct comparisons across
renovation technique families.
Figure 1 gives the common structure and the relationship between ISO 11296 and the System Standards for
other application areas.
vi © ISO 2009 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 11296-1:2011
ISO 11296-1:2009(E)
Figure 1 — Format of the renovation System Standards
© ISO 2009 – All rights reserved vii
---------------------- Page: 13 ----------------------
SIST EN ISO 11296-1:2011
---------------------- Page: 14 ----------------------
SIST EN ISO 11296-1:2011
INTERNATIONAL STANDARD ISO 11296-1:2009(E)
Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks —
Part 1:
General
1 Scope
This part of ISO 11296 specifies the requirements and test methods for plastics piping systems intended to be
used for the renovation of underground non-pressure drainage and sewerage networks, which are operated
1)
as gravity systems and subjected to a maximum surcharge pressure of 0,5 bar . It is applicable to pipes and
fittings as manufactured, as well as to the installed plastics lining system; it is not applicable to the existing
pipeline or any annular filler.
This part of ISO 11296 establishes the general requirements common to all relevant renovation techniques
(see 3.1.2).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 1610:1997, Construction and testing of drains and sewers
EN 13508-2, Conditions of drain and sewer systems outside buildings — Part 2: Visual inspection coding
system
3 Terms and definitions
For the purposes of this do
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 1. del: Splošno (ISO 11296-1:2009)Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 1: Allgemeines (ISO 11296-1:2009)Systèmes de canalisations en matières plastiques pour la rénovation des réseaux d'assainissement gravitaires enterrés - Partie 1: Généralités (ISO 11296-1:2009)Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General (ISO 11296-1:2009)93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:FprEN ISO 11296-1kSIST FprEN ISO 11296-1:2011en01-februar-2011kSIST FprEN ISO 11296-1:2011SLOVENSKI
STANDARD
kSIST FprEN ISO 11296-1:2011
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 11296-1
October 2010 ICS 23.040.20; 23.040.45; 93.030 English Version
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General (ISO 11296-1:2009)
Systèmes de canalisations en matières plastiques pour la rénovation des réseaux d'assainissement gravitaires enterrés - Partie 1: Généralités (ISO 11296-1:2009)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 1: Allgemeines (ISO 11296-1:2009) This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 11296-1:2010: EkSIST FprEN ISO 11296-1:2011
FprEN ISO 11296-1:2010 (E) 2 Contents Page Foreword .3 kSIST FprEN ISO 11296-1:2011
FprEN ISO 11296-1:2010 (E) 3 Foreword The text of ISO 11296-1:2009 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been taken over as FprEN ISO 11296-1:2010 by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This document is currently submitted to the Unique Acceptance Procedure. Endorsement notice The text of ISO 11296-1:2009 has been approved by CEN as a FprEN ISO 11296-1:2010 without any modification.
kSIST FprEN ISO 11296-1:2011
kSIST FprEN ISO 11296-1:2011
Reference numberISO 11296-1:2009(E)© ISO 2009
INTERNATIONAL STANDARD ISO11296-1First edition2009-11-01Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 1: General Systèmes de canalisations en matières plastiques pour la rénovation des réseaux d'assainissement gravitaires enterrés — Partie 1: Généralités
kSIST FprEN ISO 11296-1:2011
ISO 11296-1:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2009 – All rights reserved
kSIST FprEN ISO 11296-1:2011
ISO 11296-1:2009(E) © ISO 2009 – All rights reserved iii Contents Page Foreword.v Introduction.vi 1 Scope.1 2 Normative references.1 3 Terms and definitions.1 3.1 General terms.1 3.2 Techniques.3 3.3 Characteristics.4 3.4 Origin of materials.5 3.5 Product stages.6 4 Symbols and abbreviated terms.6 4.1 Symbols.6 4.2 Abbreviated terms.6 5 Pipes at the “M” stage.7 5.1 Materials.7 5.2 General characteristics.7 5.3 Material characteristics.7 5.4 Geometric characteristics.7 5.5 Mechanical characteristics.7 5.6 Physical characteristics.7 5.7 Jointing.7 5.8 Marking.7 6 Fittings at the “M” stage.8 6.1 Materials.8 6.2 General characteristics.8 6.3 Material characteristics.8 6.4 Geometric characteristics.8 6.5 Mechanical characteristics.8 6.6 Physical characteristics.8 6.7 Jointing.8 6.8 Marking.8 7 Ancillary components.9 8 Fitness for purpose of the installed lining system at the “I” stage.9 8.1 Materials.9 8.2 General characteristics.9 8.3 Material characteristics.9 8.4 Geometric characteristics.9 8.5 Mechanical characteristics.10 8.6 Physical characteristics.10 8.7 Additional characteristics.10 8.8 Sampling.10 9 Installation practice.10 9.1 Preparatory work.10 9.2 Storage, handling and transport of pipe and fittings.10 9.3 Equipment.10 9.4 Installation.11 9.5 Process-related inspection and testing.12 kSIST FprEN ISO 11296-1:2011
ISO 11296-1:2009(E) iv © ISO 2009 – All rights reserved 9.6 Lining termination.12 9.7 Reconnection to existing manholes and laterals.12 9.8 Final inspection and testing.12 9.9 Documentation.12 Bibliography.13
kSIST FprEN ISO 11296-1:2011
ISO 11296-1:2009(E) © ISO 2009 – All rights reserved v Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11296-1 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids. ISO 11296 consists of the following parts, under the general title Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks: ⎯ Part 1: General ⎯ Part 3: Lining with close-fit pipes ⎯ Part 4: Lining with cured-in-place pipes Lining with continuous pipes is to form the subject of a part 2, lining with discrete pipes is to form the subject of a part 5 and lining with spirally-wound pipes is to form the subject of a part 7. kSIST FprEN ISO 11296-1:2011
ISO 11296-1:2009(E) vi © ISO 2009 – All rights reserved Introduction The System Standard, of which this is part 1, specifies the requirements for plastics piping systems of various materials used for the renovation of existing pipelines in a specified application area. System Standards for renovation specify procedures for the following applications: ⎯ plastics piping systems for renovation of underground non-pressure drainage and sewerage networks; ⎯ plastics piping systems for renovation of underground drainage and sewerage networks under pressure; ⎯ plastics piping systems for renovation of underground water supply networks; ⎯ plastics piping systems for renovation of underground gas supply networks. These System Standards are distinguished from those for conventionally installed plastics piping systems because they set requirements for certain characteristics in the as-installed condition, after site processing. This is in addition to specifying requirements for system components, as manufactured. Each of the System Standards comprises a part 1 (general) and all applicable renovation technique family-related parts from the following: ⎯ part 2: lining with continuous pipes; ⎯ part 3: lining with close-fit pipes; ⎯ part 4: lining with cured-in-place pipes; ⎯ part 5: lining with discrete pipes; ⎯ part 7: lining with spirally-wound pipes.
The requirements for any given renovation technique family are given in part 1, applied in conjunction with the other relevant part. For example, parts 1 and 2 specify the requirements relating to lining with continuous pipes. For complementary information, see ISO 11295. Not all technique families are applicable to every area of application and this is reflected in the part numbers included in each System Standard. A consistent structure of clause headings has been adopted for all parts to facilitate direct comparisons across renovation technique families. Figure 1 gives the common structure and the relationship between ISO 11296 and the System Standards for other application areas. kSIST FprEN ISO 11296-1:2011
ISO 11296-1:2009(E) © ISO 2009 – All rights reserved vii
Figure 1 — Format of the renovation System Standards
kSIST FprEN ISO 11296-1:2011
kSIST FprEN ISO 11296-1:2011
INTERNATIONAL STANDARD ISO 11296-1:2009(E) © ISO 2009 – All rights reserved 1 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 1: General 1 Scope This part of ISO 11296 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground non-pressure drainage and sewerage networks, which are operated as gravity systems and subjected to a maximum surcharge pressure of 0,5 bar1). It is applicable to pipes and fittings as manufactured, as well as to the installed plastics lining system; it is not applicable to the existing pipeline or any annular filler. This part of ISO 11296 establishes the general requirements common to all relevant renovation techniques (see 3.1.2). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1610:1997, Construction and testing of drains and sewers EN 13508-2, Conditions of drain and sewer systems outside buildings — Part 2: Visual inspection coding system 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 General terms 3.1.1 pipeline system interconnecting pipe network for the conveyance of fluids 3.1.2 rehabilitation all measures for restoring or upgrading t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.