Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-201: Particular requirements for control equipment (IEC 61010-2-201:2013)

This clause of Part 1 is applicable, except as follows.
1.1.1 Equipment included in scope
Replacement:
This part of IEC 61010 specifies safety requirements and related verification tests for control
equipment of the following types:
– Programmable controllers (PLC and PAC);
– the components of Distributed Control Systems (DCS);
– the components of remote I/O – systems;
– industrial PC (computers) and Programming and Debugging Tools (PADTs);
– Human-Machine Interfaces (HMI);
– any product performing the function of control equipment and/or their associated peripherals, which have as their intended use the control and command of machines, automated manufacturing and industrial processes, e.g. discrete and continuous control. Components of the above named equipment and in the scope of this standard are:
– (auxiliary) stand-alone power supplies;
– peripherals such as digital and analogue I/O, remote-I/O;
– industrial network equipment.
Control equipment and their associated peripherals are intended to be used in an industrial environment and may be provided as open or enclosed equipment. NOTE 1 Control equipment intended also for use in other environments or for other purposes (example; for use in building installations to control light or other electrical installations, or for use on cars, trains or ships) can have additional conformity requirements defined by the safety standard(s) for these applications. These requirements can involve as example: insulation, spacings and power restrictions. NOTE 2 Computing devices and similar equipment within the scope of IEC 60950 (planned to be replaced by IEC 62368) and conforming to its requirements are considered to be suitable for use with control equipment within the scope of this standard. However, some of the requirements of IEC 60950 for resistance to moisture and liquids are less stringent than those in IEC 61010-1:2010, 5.4.4 second paragraph. Control equipment covered in this standard is intended for use in overvoltage category II (IEC 60664-1) in low-voltage installations, where the rated equipment supply voltage does not exceed a.c. 1 000 V r.m.s. (50/60 Hz), or d.c. 1 500 V. NOTE 3 If equipment in the scope of this part is applied to overvoltage category III and IV installations, then the requirements of Annex K of Part 1 apply. The requirements of ISO/IEC Guide 51 and IEC Guide 104, as they relate to this Part, are incorporated herein.
1.1.2 Equipment excluded from scope
Replacement:
This standard does not deal with aspects of the overall automated system, e.g. a complete assembly line. Control equipment (e.g. DCS and PLC), their application program and their associated peripherals are considered as components (components in this context are items which perform no useful function by themselves) of an overall automated system. Since control equipment (e.g. DCS and PLC) are component devices, safety considerations for the overall automated system including installation and application are beyond the scope of this standard. Refer to IEC 60364 series of standards or applicable national/local regulations for electrical installation and guidelines.
1.2.1 Aspects included in scope
Replacement:
The purpose of the requirements of this standard is to ensure that all hazards to the operator, service personnel and the surrounding area are reduced to a tolerable level.

Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2-201: Besondere Anforderungen für Steuer- und Regelgeräte (IEC 61010-2-201:2013)

Règles de sécurité pour appareils électriques de mesurage, de régulation et de laboratoire - Partie 2-201: Exigences particulières relatives aux équipements de commande (CEI 61010-2-201:2013)

La CEI 60101-2-201:2013 spécifie l'ensemble des exigences de sécurité relatives aux équipements de commande (par exemple les automates programmables (AP)), aux composants des systèmes à commande distribuée, aux appareils d'E/S et à l'interface homme/machine. Les termes de sécurité d'usage général sont définis dans la CEI 61010-1. Des termes plus spécifiques sont définis dans chaque partie. Cette partie contient les exigences relatives à la sécurité des automates programmables. L'Annexe DD établit une référence croisée entre les articles de la présente norme et ceux de la CEI 61010-1 ou de la CEI 61131-2:2007. Elle a le statut d'une publication fondamentale de sécurité conformément au Guide CEI 104.

Varnostne zahteve za električno opremo za meritve, nadzor in laboratorijsko uporabo - 2-201. del: Posebne zahteve za opremo za nadzor in upravljanje (IEC 61010-2-201:2013)

Ta točka 1. dela se uporablja, razen kot sledi:
1.1.1 Oprema, zajeta v področje uporabe
Nadomestitev:
Ta del standarda IEC 61010 določa zahteve glede varnosti in s tem povezane preskuse opreme
za upravljanje naslednjih vrst:
– programirljivi krmilniki (PLC in PAC);
– komponente porazdeljenih nadzornih sistemov (DCS)
– komponente daljinskih sistemov I/O;
– industrijska računalniška orodja in orodja za programiranje in iskanje napak (PADTs);
– vmesniki človek-stroj (HMI);
– vsak izdelek, ki deluje kot oprema za upravljanje in/ali njegove povezane periferne naprave, namenjene upravljanju in krmiljenju strojev, avtomatiziranih proizvodnih in industrijskih postopkov, npr. diskretno in neprekinjeno krmiljenje. Komponente zgoraj omenjene opreme in v področju uporabe tega standarda so:
– (pomožni) samostojno stoječi električni napajalniki
– periferne naprave, kot so digitalni in analogni I/O, daljinski I/O;
– industrijska omrežna oprema.
Oprema za upravljanje in njene povezane periferne naprave so namenjene uporabi v industrijskem okolju in so lahko na voljo kot odprta ali zaprta oprema. OPOMBA 1: Oprema za upravljanje, ki se uporablja tudi v drugih okoljih ali v druge namene (na primer v inštalacijah zgradb za upravljanje luči ali drugih električnih inštalacijah, ali za uporabo v avtomobilih, vlakih ali na ladjah), ima dodatne zahteve o skladnosti, določene z varnostnimi standardi za omenjene uporabe. Te zahteve lahko na primer zajemajo:izolacijo, razmike in omejitve moči. OPOMBA 2: Računalniške naprave in podobna oprema, ki so vključene v področje uporabe standarda IEC 60950 (zamenjal naj bi ga standard IEC 62368) in so v skladu z njegovimi zahtevami, se smatrajo kot primerne za uporabo z opremo za upravljanje iz področja uporabe tega standarda. Vendar pa so nekatere zahteve standarda IEC 60950 za odpornost na vlago in tekočine manj stroge od zahtev v drugem odstavku točke 5.4.4. standarda IEC 61010-1:2010. Oprema za upravljanje, zajeta v tem standardu, je namenjena uporabi v prenapetostni kategoriji II (IEC 60664-1) v nizkonapetostnih inštalacijah, kjer nazivna napajalna napetost opreme ne presega 1000 V efektivne izmenične napetosti (50/60 Hz), ali 1500 V enosmerne napetosti. OPOMBA 3 Če je za inštalacije prenapetostne kategorije III in IV uporabljena oprema iz področja uporabe tega dela, veljajo zahteve dodatka K 1. dela. Zahteve iz ISO/IEC Guide 51 in IEC Guide 104 so vključene v to besedilo, ker se nanašajo na ta del.
1.1.2 Oprema, izključena iz področja uporabe
Nadomestitev:
Ta standard ne obravnava vidikov v celoti avtomatiziranega sistema, npr. tekočega traka. Oprema za upravljanje (npr. DSC in PLC), njen aplikacijski program in povezane periferne naprave veljajo za komponente (komponente so v tem pomenu deli, ki sami nimajo posebne uporabne funkcije) v celoti avtomatiziranega sistema. Ker je oprema za upravljanje (npr. DCS in PLC) komponentna naprava, so varnostni napotki za v celoti avtomatiziran sistem, vključno z namestitvijo in uporabo, izven področja uporabe tega standarda. Glejte skupino standardov IEC 60364 ali veljavne nacionalne/lokalne predpise za električne inštalacije in smernice.

General Information

Status
Withdrawn
Publication Date
28-May-2013
Withdrawal Date
29-Nov-2022
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
28-Nov-2022
Due Date
21-Dec-2022
Completion Date
30-Nov-2022

Relations

Buy Standard

Standard
EN 61010-2-201:2013 - BARVE
English language
59 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61010-2-201:2013
01-julij-2013
1DGRPHãþD
SIST EN 61131-2:2007
9DUQRVWQH]DKWHYH]DHOHNWULþQRRSUHPR]DPHULWYHQDG]RULQODERUDWRULMVNR
XSRUDERGHO3RVHEQH]DKWHYH]DRSUHPR]DQDG]RULQXSUDYOMDQMH ,(&

Safety requirements for electrical equipment for measurement, control, and laboratory
use - Part 2-201: Particular requirements for control equipment (IEC 61010-2-201:2013)
Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2
-201: Besondere Anforderungen für Steuer- und Regelgeräte (IEC 61010-2-201:2013)
Règles de sécurité pour appareils électriques de mesurage, de régulation et de
laboratoire - Partie 2-201: Exigences particulières relatives aux équipements de
commande (CEI 61010-2-201:2013)
Ta slovenski standard je istoveten z: EN 61010-2-201:2013
ICS:
19.080 (OHNWULþQRLQHOHNWURQVNR Electrical and electronic
SUHVNXãDQMH testing
71.040.10 Kemijski laboratoriji. Chemical laboratories.
Laboratorijska oprema Laboratory equipment
SIST EN 61010-2-201:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61010-2-201:2013

---------------------- Page: 2 ----------------------

SIST EN 61010-2-201:2013

EUROPEAN STANDARD
EN 61010-2-201

NORME EUROPÉENNE
May 2013
EUROPÄISCHE NORM

ICS 13.110; 17.020; 19.020; 25.040.40 Supersedes EN 61131-2:2007 (partially)


English version


Safety requirements for electrical equipment for measurement, control
and laboratory use -
Part 2-201: Particular requirements for control equipment
(IEC 61010-2-201:2013)


Règles de sécurité pour appareils Sicherheitsbestimmungen für elektrische
électriques de mesurage, de régulation et Mess-, Steuer-, Regel- und Laborgeräte -
de laboratoire - Teil 2-201: Besondere Anforderungen für
Partie 2-201: Exigences particulières pour Steuer- und Regelgeräte
les équipements de commande (IEC 61010-2-201:2013)
(CEI 61010-2-201:2013)





This European Standard was approved by CENELEC on 2013-04-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61010-2-201:2013 E

---------------------- Page: 3 ----------------------

SIST EN 61010-2-201:2013
EN 61010-2-201:2013 - 2 -

Foreword
The text of document 65/515/FDIS, future edition 1 of IEC 61010-2-201, prepared by IEC TC 65
"Industrial-process measurement, control and automation" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN 61010-2-201:2013.
The following dates are fixed:
• latest date by which the document has (dop) 2014-01-01
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2016-04-01
• latest date by which the national
standards conflicting with the

document have to be withdrawn

This document partially supersedes EN 61131-2:2007.
This Part 2-201 is intended to be used in conjunction with EN 61010-1:2010. Consideration may be given
to future editions of, or amendments to, EN 61010-1.
This Part 2-201 supplements or modifies the corresponding clauses in EN 61010-1 so as to convert that
publication into the European standard: Particular requirements for control equipment.
Where a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies as far as is
reasonable. Where this part states “addition”, “modification”, “replacement”, or “deletion”, the relevant
requirement, test specification or note in Part 1 should be adapted accordingly.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed
for Use within Certain Voltage Limits (LVD - 2006/95/EC).

Endorsement notice
The text of the International Standard IEC 61010-2-201:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60079 series NOTE  Harmonised in EN 60079 series.
IEC 60364 series NOTE  Harmonised in HD 60364 series.
IEC 60364-4-41 NOTE  Harmonised as HD 60364-4-41.
IEC 60664-5:2007 NOTE  Harmonised as EN 60664-5:2007 (not modified).
IEC 60715:1981 + NOTE  Harmonised as EN 60715:2001 (not modified).
A1:1995
IEC 60721-2-3:1987 NOTE  Harmonised as HD 478.2.3 S1:1990 (not modified).
IEC 61131-2:2007 NOTE  Harmonised as EN 61131-2:2007 (not modified).
IEC 61131-6:2012 NOTE  Harmonised as EN 61131-6:2012 (not modified).
IEC 61140:2001 NOTE  Harmonised as EN 61140:2002 (not modified).
IEC 61326 series NOTE  Harmonised in EN 61326 series.

---------------------- Page: 4 ----------------------

SIST EN 61010-2-201:2013
- 3 - EN 61010-2-201:2013
IEC 61508 series NOTE  Harmonised in EN 61508 series.
IEC 61643 series NOTE  Harmonised in EN 61643 series.
IEC 61643-21 NOTE  Harmonised as EN 61643-21.
IEC 61643-311 NOTE  Harmonised as EN 61643-311.
IEC 61643-321 NOTE  Harmonised as EN 61643-321.
IEC 61643-331 NOTE  Harmonised as EN 61643-331.
IEC 61800 series NOTE  Harmonised in EN 61800 series.
IEC 62133:2002 NOTE  Harmonised as EN 62133:2003 (not modified).
IEC 62368 series NOTE  Harmonised in EN 62368 series.

---------------------- Page: 5 ----------------------

SIST EN 61010-2-201:2013
EN 61010-2-201:2013 - 4 -
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Addition to Annex ZA of EN 61010-1:2010:

Publication Year Title EN/HD Year

IEC 60068-2-31 2008 Environmental testing - EN 60068-2-31 2008
Part 2-31: Tests - Test Ec: Rough handling
shocks, primarily for equipment-type
specimens


IEC 60384-14 2005 Fixed capacitors for use in electronic EN 60384-14 2005
equipment -
Part 14: Sectional specification - Fixed
capacitors for electromagnetic interference
suppression and connection to the supply
mains


IEC 60664-1 2007 Insulation coordination for equipment within EN 60664-1 2007
low-voltage systems -
Part 1: Principles, requirements and tests


IEC 60695-2-11 2000 Fire hazard testing - EN 60695-2-11 2001
+ corr. January 2001 Part 2-11: Glowing/hot-wire based test
methods - Glow-wire flammability test method
for end-products


IEC 60947-5-1 2003 Low-voltage switchgear and controlgear - EN 60947-5-1 2004
Part 5-1: Control circuit devices and switching + corr. July 2005
elements - Electromechanical control circuit
devices


IEC 60947-7-1 2009 Low-voltage switchgear and controlgear - EN 60947-7-1 2009
Part 7-1: Ancillary equipment - Terminal
blocks for copper conductors


IEC 61010-1 2010 Safety requirements for electrical equipment EN 61010-1 2010
+ corr. May 2011 for measurement, control and laboratory use -
Part 1: General requirements


IEC 61010-2-030 - Safety requirements for electrical equipment EN 61010-2-030 -
for measurement, control and laboratory use -
Part 2-030: Particular requirements for testing
and measuring circuits


IEC 61051-2 1991 Varistors for use in electronic equipment - - -
Part 2: Sectional specification for surge
suppression varistors

---------------------- Page: 6 ----------------------

SIST EN 61010-2-201:2013




IEC 61010-2-201

®


Edition 1.0 2013-02




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside



BASIC SAFETY PUBLICATION

PUBLICATION FONDAMENTALE DE SÉCURITÉ




Safety requirements for electrical equipment for measurement, control, and

laboratory use –

Part 2-201: Particular requirements for control equipment




Règles de sécurité pour appareils électriques de mesurage, de régulation et de

laboratoire –


Partie 2-201: Exigences particulières pour les équipements de commande













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX XA


ICS 13.110; 17.020; 19.020; 25.040.40 ISBN 978-2-83220-588-4



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61010-2-201:2013
– 2 – 61010-2-201 © IEC:2013
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope and object . 8
1.1.1 Equipment included in scope . 8
1.1.2 Equipment excluded from scope . 9
1.2.1 Aspects included in scope . 9
1.2.2 Aspects excluded from scope . 9
2 Normative references . 10
3 Terms and definitions . 10
4 Tests . 12
4.1 General . 12
4.3.2 State of equipment . 12
4.4 Testing in single fault condition . 12
5 Marking and documentation . 14
5.4.3 Equipment installation . 14
6 Protection against electric shock . 14
6.1.2 Exceptions . 14
6.2.1 General . 14
6.2.2 Examination . 14
6.2.3 Openings above parts that are hazardous live . 14
6.2.4 Openings for pre-set controls . 15
6.2.101 Accessibility of interfaces/ports/terminals . 15
6.2.102 Control equipment . 17
6.6.1 General . 20
6.6.2 Terminals for external circuits . 20
6.6.3 Circuits with terminals which are hazardous live . 20
6.6.4 Terminals for stranded conductors . 20
6.7.2 Insulation for mains circuits of overvoltage category II with a nominal
supply voltage up to 300 V . 22
6.7.3 Insulation for secondary circuits derived from mains circuits of
overvoltage category II up to 300 V . 24
6.7.101 Insulation for field wiring terminals of overvoltage category II with a
nominal voltage up to 1 000 V . 26
6.8.3 Test procedures . 26
6.10 Connection to the mains supply source and connections between parts of
equipment . 26
6.11 Disconnection from supply source . 27
7 Protection against mechanical hazards . 27
7.1.101 Open and panel mounted equipment . 27
7.2 Sharp edges . 27
7.3.3 Risk assessment for mechanical hazards to body parts . 27
7.3.4 Limitation of force and pressure. 28
7.3.5 Gap limitations between moving parts . 28
7.7 Expelled parts . 28
8 Resistance to mechanical stresses . 28
8.1.101 Open equipment . 28

---------------------- Page: 8 ----------------------

SIST EN 61010-2-201:2013
61010-2-201 © IEC:2013 – 3 –
8.1.102 Panel mounted equipment . 28
8.2.2 Impact test . 28
8.3 Drop test . 28
8.3.1 Equipment other than hand-held equipment and direct plug-in
equipment . 29
8.3.2 Hand-held equipment and direct plug-in equipment . 29
9 Protection against the spread of fire . 29
9.2 Eliminating or reducing the sources of ignition within the equipment . 29
9.3.2 Constructional requirements . 29
10 Equipment temperature limits and resistance to heat . 30
10.1 Surface temperature limits for protection against burns . 30
10.3 Other temperature measurements . 31
10.4.1 General . 31
10.4.2 Temperature measurement of heating equipment . 32
10.4.3 Equipment intended for installation in a cabinet or a wall . 32
10.5.2 Non-metallic enclosures . 33
11 Protection against hazards from fluids . 33
11.6 Specially protected equipment . 33
12 Protection against radiation, including laser sources, and against sonic and
ultrasonic pressure . 33
13 Protection against liberated gases and substances, explosion and implosion . 34
13.1 Poisonous and injurious gases and substances . 34
13.2.1 Components . 34
13.2.2 Batteries and battery charging . 34
14 Components and subassemblies . 34
14.101 Components bridging insulation . 34
14.101.1 Capacitors . 34
14.101.2 Surge surpressors . 34
14.102 Switching devices . 35
15 Protection by interlocks . 35
16 Hazards resulting from application . 35
17 Risk assessment . 35
Annexes . 35
Annex F (normative) Routine tests . 36
Annex L (informative) Index of defined terms . 38
Annex AA (informative) General approach to safety for control equipment . 39
Annex BB (informative) System drawing of isolation boundaries . 41
Annex CC (informative) Historical techniques for secondary circuits . 49
Annex DD (informative) Cross references between IEC 61010-2-201 and IEC 61010-
1:2010 or IEC 61131-2:2007 . 53
Bibliography . 54

Figure 101 – Typical interface/port diagram of control equipment. 16
Figure 102 – Requirements for insulation between separate circuits and between
circuits and accessible conductive parts . 21
Figure 103 – Mechanical hazards requirements for panel mounted equipment . 27
Figure 104 – Safety enclosure with HMI installed through a wall . 30

---------------------- Page: 9 ----------------------

SIST EN 61010-2-201:2013
– 4 – 61010-2-201 © IEC:2013
Figure 105 – Panel mounted HMI device extending through the wall of a cabinet . 33
Figure AA.1 – Control equipment access and safety concerns . 39
Figure BB.1 – Typical system enclosure layout . 42
Figure BB.2 – Simplified system schematic . 43
Figure BB.3 – Hazard situation of the control equipment . 44
Figure BB.4 – Application of the standard to the control equipment safety drawing . 45
Figure BB.5 – Reinforced insulation . 46
Figure BB.6 – Basic insulation . 47
Figure BB.7 – Reinforced insulation, basic insulation and limiting impedance . 48

Table 101 – Overload test circuit values . 13
Table 102 – Endurance test circuit values . 13
Table 103 – Operator accessibility for open and enclosed equipment . 16
Table 4 – Clearance and creepage distances for mains circuits of overvoltage category
II up to 300 V . 23
Table 5 – Test voltages for solid insulation between mains and between mains and
d
secondary circuits overvoltage category II up to 300 V . 24
Table 6 – Clearances and test voltages for secondary circuits derived from mains
circuits of overvoltage category II up to 300 V . 25
Table 104 – Minimum creepages and clearances in air of overvoltage category II up to
1 000 V at field-wiring terminals . 26
Table 105 – Drop tests . 29
Table 19 – Surface temperature limits, under normal conditions . 31
Table CC.1 – Limits of output current and output power for inherently limited power
sources . 51
Table CC.2 – Limits of output current, output power and ratings for over-current
protective devices for non-inherently limited power sources . 52
Table DD.1 – Cross-references between IEC 61010-2-201 and IEC 61010-1 or
IEC 61131-2 . 53

---------------------- Page: 10 ----------------------

SIST EN 61010-2-201:2013
61010-2-201 © IEC:2013 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT
FOR MEASUREMENT, CONTROL, AND LABORATORY USE –

Part 2-201: Particular requirements for control equipment


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61010-2-201 has been prepared by IEC technical committee 65:
Industrial-process measurement, control and automation.
The text of this standard is based on the following documents:
FDIS Report on voting
65/515/FDIS 65/521/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This Part 2-201 is intended to be used in conjunction with IEC 61010-1. It was established on
the basis of the third edition (2010). Consideration may be given to future editions of, or
amendments to, IEC 61010-1.

---------------------- Page: 11 ----------------------

SIST EN 61010-2-201:2013
– 6 – 61010-2-201 © IEC:2013
This Part 2-201 supplements or modifies the corresponding clauses in IEC 61010-1 so as to
convert that publication into the IEC standard: Particular requirements for control equipment.
Where a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies
as far as is reasonable. Where this part states “addition”, “modification”, “replacement”, or
“deletion”, the relevant requirement, test specification or note in Part 1 should be adapted
accordingly.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
It has the status of a basic safety publication in accordance with IEC Guide 104.
A list of all parts in the IEC 61010 series, published under the general title Safety
requirements for electrical equipment for measurement, control and laboratory use, can be
found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful f
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.