SIST EN ISO 17663:2023
(Main)Welding - Quality requirements for heat treatment in connection with welding and allied processes (ISO 17663:2023)
Welding - Quality requirements for heat treatment in connection with welding and allied processes (ISO 17663:2023)
ISO 17663:2009 provides quality requirements for heat treatment in air or controlled atmospheres carried out in workshops and on site in connection with welding and forming. It applies mainly to ferritic steels, but can be used for other materials, as appropriate.
ISO 17663:2009 provides guidance for manufacturers that perform heat treatment or produce heat-treated products or components. ISO 17663:2009 can also be used as a basis for assessing the manufacturer in respect to its heat treatment capability.
ISO 17663:2009 is intended to be a flexible framework for the control of heat treatment processes. The fulfilment of a requirement can be waived where justification can be provided that a specific requirement is not applicable to a specific process.
Schweißen - Qualitätsanforderungen zur Wärmebehandlung beim Schweißen und bei verwandten Prozessen (ISO 17663:2023)
Dieses Dokument stellt Qualitätsanforderungen für die Wärmebehandlung in Luft oder überwachten Atmosphären bereit, die in Werkstätten und auf Baustellen in Verbindung mit Schweiß und Umformarbeiten durchgeführt wird. Es gilt hauptsächlich für ferritische Stähle, kann jedoch auch für andere Werkstoffe angewendet werden, sofern zutreffend.
Dieses Dokument stellt Herstellern, die Wärmebehandlungen durchführen oder wärmebehandelte Produkte oder Bauteile fertigen, einen Leitfaden zur Verfügung. Dieses Dokument kann auch als Grundlage für die Beurteilung des Herstellers hinsichtlich seiner Eignung zur Wärmebehandlung verwendet werden.
Auf die Erfüllung einer Anforderung kann verzichtet werden, wenn belegt werden kann, dass eine bestimmte Anforderung nicht auf einen speziellen Prozess anwendbar ist. Dieses Dokument ist als flexibler Rahmen vorgesehen, um Folgendes bereitzustellen:
besondere Anforderungen an die Wärmebehandlung durch Hersteller, damit deren Qualitätssystem ISO 9001 entspricht;
besondere Anforderungen an die Wärmebehandlung in Spezifikationen, welche verlangen, dass der Hersteller über ein anderes Qualitätssystem als das nach ISO 9001 verfügen muss;
einen besonderen Leitfaden für einen Hersteller, der ein Qualitätskontrollsystem für die Wärme-behandlung entwickelt;
einen besonderen Leitfaden für die Wärmebehandlung nach dem Schweißen für Hersteller, die nach ISO 3834 2 oder ISO 3834 3 arbeiten;
detaillierte Anforderungen an Spezifikationen, Bestimmungen oder Produktnormen, die eine Kontrolle von Wärmebehandlungstätigkeiten fordern.
Soudage - Exigences de qualité relatives au traitement thermique associé au soudage et aux techniques connexes (ISO 17663:2023)
L'ISO 17663:2009 spécifie des exigences de qualité relatives au traitement thermique à l'air libre ou en atmosphères contrôlées, appliqué en atelier ou sur chantier en soudage et en formage. Ce traitement s'applique principalement aux aciers ferritiques, mais peut être utilisé pour d'autres matériaux, le cas échéant.
L'ISO 17663:2009 fournit des directives aux constructeurs et aux fabricants qui réalisent un traitement thermique ou qui fabriquent des produits ou des pièces traités thermiquement. La présente Norme internationale peut également servir de base pour évaluer la compétence d'un constructeur ou d'un fabricant dans le domaine du traitement thermique.
L'ISO 17663:2009 est censée être un cadre souple pour la maîtrise des traitements thermiques. La réalisation d'une exigence peut être écartée si la justification peut être fournie qu'une exigence spécifique ne s'applique pas à un traitement spécifique.
Varjenje - Zahteve za kakovost pri toplotni obdelavi v povezavi z varjenjem in sorodnimi postopki (ISO 17663:2023)
Standard ISO 17663:2009 vsebuje zahteve za kakovost pri toplotni obdelavi v atmosferah z zrakom ali nadzorovanih atmosferah, ki se izvaja v delavnicah ali na mestu uporabe v povezavi z varjenjem in oblikovanjem. Uporablja se predvsem za feritna jekla, kjer je to ustrezno, pa ga je mogoče uporabiti za druge materiale.
Standard ISO 17663:2009 določa smernice za proizvajalce, ki izvajajo toplotno obdelavo ali izdelujejo toplotno obdelane proizvode ali sestavne dele. Uporabiti ga je mogoče tudi kot osnovo za ocenjevanje proizvajalca v povezavi z njegovo sposobnostjo toplotnega obdelovanja.
Standard je zasnovan kot prilagodljiv okvir za nadzor procesov toplotne obdelave. Izpolnitev zahteve je mogoče opustiti, če je mogoče utemeljiti, da se posamezna zahteva ne uporablja za določen proces.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 17663:2023
01-julij-2023
Nadomešča:
SIST EN ISO 17663:2010
Varjenje - Zahteve za kakovost pri toplotni obdelavi v povezavi z varjenjem in
sorodnimi postopki (ISO 17663:2023)
Welding - Quality requirements for heat treatment in connection with welding and allied
processes (ISO 17663:2023)
Schweißen - Qualitätsanforderungen zur Wärmebehandlung beim Schweißen und bei
verwandten Prozessen (ISO 17663:2023)
Soudage - Exigences de qualité relatives au traitement thermique associé au soudage et
aux techniques connexes (ISO 17663:2023)
Ta slovenski standard je istoveten z: EN ISO 17663:2023
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
SIST EN ISO 17663:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 17663:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 17663:2023
EN ISO 17663
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2023
EUROPÄISCHE NORM
ICS 25.160.01 Supersedes EN ISO 17663:2009
English Version
Welding - Quality requirements for heat treatment in
connection with welding and allied processes (ISO
17663:2023)
Soudage - Exigences de qualité relatives au traitement Schweißen - Qualitätsanforderungen zur
thermique associé au soudage et aux techniques Wärmebehandlung beim Schweißen und bei
connexes (ISO 17663:2023) verwandten Prozessen (ISO 17663:2023)
This European Standard was approved by CEN on 4 May 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17663:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 17663:2023
EN ISO 17663:2023 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 17663:2023
EN ISO 17663:2023 (E)
European foreword
This document (EN ISO 17663:2023) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2023, and conflicting national standards
shall be withdrawn at the latest by November 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 17663:2009.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 17663:2023 has been approved by CEN as EN ISO 17663:2023 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 17663:2023
---------------------- Page: 6 ----------------------
SIST EN ISO 17663:2023
INTERNATIONAL ISO
STANDARD 17663
Second edition
2023-04
Welding — Quality requirements for
heat treatment in connection with
welding and allied processes
Soudage — Exigences de qualité relatives au traitement thermique
associé au soudage et aux techniques connexes
Reference number
ISO 17663:2023(E)
© ISO 2023
---------------------- Page: 7 ----------------------
SIST EN ISO 17663:2023
ISO 17663:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2023 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 17663:2023
ISO 17663:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Review of requirements and technical review . 2
4.1 General . 2
4.2 Review of requirements . 2
4.3 Technical review . 3
5 Subcontracting . 3
6 Personnel . 3
7 Inspection and testing .4
7.1 General . 4
7.2 Non-destructive testing . 4
7.3 Destructive testing . 4
8 Equipment for heat treatment . 4
8.1 Production and testing equipment . 4
8.2 Description of facilities . 4
8.3 Suitability of equipment . 5
8.4 Verification of heat treatment equipment . 5
8.4.1 General . 5
8.4.2 Measurement of the uniformity of furnace temperature . 5
8.4.3 Validation of setting and recording devices . 6
8.5 New equipment . 6
8.6 Maintenance . 6
9 Heat treatment activities . 6
9.1 General . 6
9.2 Heat treatment parameters . 6
9.3 Heat treatment procedure specification . 7
9.4 Work instructions . 7
9.5 Number of measuring points . 7
9.6 Guidance for local post-weld heat treatment of welds in pipe work . 8
10 Heat treatment record . 9
11 Non-conformity and corrective actions . 9
12 Quality records .10
Annex A (informative) Example of local heat treatment .11
Bibliography .12
iii
© ISO 2023 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 17663:2023
ISO 17663:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 10, Quality management in the field of welding, in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 121, Welding and allied processes,
in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 17663:2009), which has been technically
revised.
The main changes are as follows:
— normative references updated;
— arc stud welding added in 9.5;
— Figure A.1 revised.
Any feedback or questions on this document should be directed to the user’s national standards
body. A complete listing of these bodies can be found at www.iso.org/members.html. Official
interpretations of ISO/TC 44 documents, where they exist, are available from this page:
https://committee.iso.org/sites/tc44/home/interpretation.html.
iv
© ISO 2023 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 17663:2023
INTERNATIONAL STANDARD ISO 17663:2023(E)
Welding — Quality requirements for heat treatment in
connection with welding and allied processes
1 Scope
This document provides quality requirements for heat treatment in air or controlled atmospheres
carried out in workshops and on site in connection with welding and forming. It applies mainly to
ferritic steels but can be used for other materials as appropriate.
This document provides guidance for manufacturers that perform heat treatment or produce
heat-treated products or components. This document can also be used as a basis for assessing the
manufacturer in respect to its heat treatment capability.
The fulfilment of a requirement can be waived where justification can be provided that a specific
requirement is not applicable to a specific process. This document is intended to be a flexible framework
to provide:
— specific requirements for heat treatment by manufacturers in order to have a quality system in
accordance with ISO 9001;
— specific requirements for heat treatment in specifications which require the manufacturer to have
a quality system other than ISO 9001;
— specific guidance for a manufacturer developing a quality control system for heat treatment;
— specific guidance for post-weld heat treatment for manufacturers adopting ISO 3834-2 or ISO 3834-3;
— detailed requirements for specifications, regulations or product standards that require control of
heat treatment activities.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 4885, Ferrous materials — Heat treatments — Vocabulary
ISO 13916, Welding — Measurement of preheating temperature, interpass temperature and preheat
maintenance temperature
IEC 60584-1, Thermocouples — Part 1: EMF specifications and tolerances
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4885 and ISO 13916 and the
following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
1
© ISO 2023 – All rights reserved
---------------------- Page: 11 ----------------------
SIST EN ISO 17663:2023
ISO 17663:2023(E)
3.1
manufacturer
person or organization responsible for heat treatment of products or components
3.2
loading temperature
temperature of the furnace at the stage when the product or component is put into the furnace
3.3
holding temperature
temperature at which the product or component is kept in order to achieve the specified properties
Note 1 to entry: The holding temperature depends on the type of heat treatment, type of material and material
thickness.
Note 2 to entry: Normally, the holding temperature is expressed as a temperature range.
3.4
holding time
time the product or component is kept at the holding temperature
Note 1 to entry: The holding time starts when the temperature at all measuring points has reached the minimum
value of the range of the holding temperature and stops when one of the measuring points falls below that
temperature.
Note 2 to entry: The holding time depends on the type of heat treatment, material and material thickness.
3.5
unloading temperature
temperature of the product or component when it is taken out of a furnace or when the heat source is
removed or switched off in any other heat treatment, e.g. local heat treatment
3.6
section temperature range
temperature r
...
SLOVENSKI STANDARD
oSIST prEN ISO 17663:2022
01-september-2022
Varjenje - Zahteve za kakovost pri toplotni obdelavi v povezavi z varjenjem in
sorodnimi postopki (ISO/DIS 17663:2022)
Welding - Quality requirements for heat treatment in connection with welding and allied
processes (ISO/DIS 17663:2022)
Schweißen – Qualitätsanforderungen zur Wärmebehandlung beim Schweißen und bei
verwandten Prozessen (ISO/DIS 17663:2022)
Soudage - Exigences de qualité relatives au traitement thermique associé au soudage et
aux techniques connexes (ISO/DIS 17663:2022)
Ta slovenski standard je istoveten z: prEN ISO 17663
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
oSIST prEN ISO 17663:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 17663:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 17663:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 17663
ISO/TC 44/SC 10 Secretariat: DIN
Voting begins on: Voting terminates on:
2022-07-13 2022-10-05
Welding — Quality requirements for heat treatment in
connection with welding and allied processes
Soudage — Exigences de qualité relatives au traitement thermique associé au soudage et aux techniques
connexes
ICS: 25.160.01
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 17663:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 17663:2022
ISO/DIS 17663:2022(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 17663
ISO/TC 44/SC 10 Secretariat: DIN
Voting begins on: Voting terminates on:
Welding — Quality requirements for heat treatment in
connection with welding and allied processes
Soudage — Exigences de qualité relatives au traitement thermique associé au soudage et aux techniques
connexes
ICS: 25.160.01
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2022
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 17663:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
© ISO 2022 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 4 ----------------------
oSIST prEN ISO 17663:2022
ISO/DIS 17663:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Review of requirements and technical review . 2
4.1 General . 2
4.2 Review of requirements . 2
4.3 Technical review . 3
5 Subcontracting . 3
6 Personnel . 3
7 Inspection and testing .4
7.1 General . 4
7.2 Non-destructive testing . 4
7.3 Destructive testing . 4
8 Equipment for heat treatment . 4
8.1 Production and testing equipment . 4
8.2 Description of facilities . 4
8.3 Suitability of equipment . 5
8.4 Verification of heat treatment equipment . 5
8.4.1 General . 5
8.4.2 Measurement of the uniformity of furnace temperature . 5
8.4.3 Validation of setting and recording devices . 6
8.5 New equipment . 6
8.6 Maintenance . 6
9 Heat treatment activities . 6
9.1 General . 6
9.2 Heat treatment parameters . 6
9.3 Heat treatment procedure specification . 7
9.4 Work instructions . 7
9.5 Number of measuring points . 7
9.6 Guidance for local post weld heat treatment of welds in pipe work . 8
10 Heat treatment record . 9
11 Non-conformance and corrective actions . 9
12 Quality records .10
Annex A (informative) Example of local heat treatment .11
Bibliography .12
iii
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 17663:2022
ISO/DIS 17663:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 10, Quality management in the field of welding.
This second edition cancels and replaces the first edition (ISO 17663:2009), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— update of normative references;
— under sub-clause 9.5 arc stud welding added;
— figure A.1 in annex A revised.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2022 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 17663:2022
DRAFT INTERNATIONAL STANDARD ISO/DIS 17663:2022(E)
Welding — Quality requirements for heat treatment in
connection with welding and allied processes
1 Scope
This document provides quality requirements for heat treatment in air or controlled atmospheres
carried out in workshops and on site in connection with welding and forming. It applies mainly to
ferritic steels, but can be used for other materials, as appropriate.
This International Standard provides guidance for manufacturers that perform heat treatment or
produce heat treated products or components. This document can also be used as a basis for assessing
the manufacturer in respect to its heat treatment capability.
The fulfilment of a requirement can be waived where justification can be provided that a specific
requirement is not applicable to a specific process. This document is intended to be a flexible framework
to provide:
— specific requirements for heat treatment by manufacturer in order to have a quality system in
accordance with ISO 9001;
— specific requirements for heat treatment in specifications which require the manufacturer to have
a quality system other than ISO 9001;
— specific guidance for a manufacturer developing a quality control system for heat treatment;
— specific guidance for post weld heat treatment for manufacturers adopting ISO 3834-2 or ISO 3834-3;
— detailed requirements for specifications, regulations or product standards that require control of
heat treatment activities.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 4885, Ferrous materials — Heat treatments — Vocabulary
ISO 13916, Welding — Measurement of preheating temperature, interpass temperature and preheat
maintenance temperature
IEC 60584-1, Thermocouples — Part 1: EMF specifications and tolerances
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 13916 and ISO 4885 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
1
© ISO 2022 – All rights reserved
---------------------- Page: 7 ----------------------
oSIST prEN ISO 17663:2022
ISO/DIS 17663:2022(E)
3.1
manufacturer
person or organization responsible for heat treatment of products or components
3.2
loading temperature
temperature of the furnace at the stage when the product or component is put into the furnace
3.3
holding temperature
temperature at which the product or component is kept in order to achieve the specified properties
Note 1 to entry: The holding temperature depends on the type of heat treatment, type of material and material
thickness.
Note 2 to entry: Normally, the holding temperature is expressed as a temperature range.
3.4
holding time
time the product or component is kept at the holding temperature
Note 1 to entry: The holding time starts when the temperature at all measuring points has reached the minimum
value of the range of the holding temperature and stops when one of the measuring points falls below that
temperature.
Note 2 to entry: The holding time depends on the type of heat treatment, material and material thickness.
3.5
unloading temperature
temperature of the product or component when it is taken out of a furnace or when the heat source is
removed or switched off in any other heat treatment, e.g. local heat treatment
3.6
section temperature range
temperature range with a specified linear distance that can vary between two adjacent measuring
points
4 Review of requirements and technical review
4.1 General
The manufacturer shall review the contractual requirements and any other requirements together
with any technical data. This is to ensure that all information necessary to carry out the heat treatment
operations is available prior to the commencement of the work. The manufacturer shall affirm its
capability to meet all requirements and ensure adequate planning of all quality-related activities.
The review of requirements is carried out by the manufacturer to verify that the work content is within
its capability to perform, that sufficient resources are available to achieve delivery schedules and that
documentation is clear and unambiguous. The manufacturer shall ensure that variations between the
contract and previous quotation are identified.
4.2 Review of requirements
Aspects for consideration shall include the following:
a) product standard used, together with any supplementary requirements;
b) statutory and regulatory requirements;
c) any additional requirement determined by the manufacturer;
2
© ISO 2022 – All rights
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.