SIST EN ISO 11592:2002

Small craft less than 8 m length of hull - Determination of maximum propulsion power rating (ISO 11592:2001)

This part of ISO 11592 establishes the basis for the determination of the maximum power for propulsion and the manoeuvring speed for occupant safety in engine-powered small craft less than 8 m length of hull. The following types of small craft are exempted from the application of this standard: - Personal water   craft: for purposes of this standard, craft less than 4 m length of hull, with internal combustion engine/water jet or propeller drive, designed for sitting, standing or kneeling on, rather than sitting inside - Sailing craft - Canoes and kayaks.

Kleine Wasserfahrzeuge bis 8m Rumpflänge - Bestimmung der maximalen Vortriebsleistung (ISO 11592:2001)

Diese Internationale Norm legt Anforderungen für die Bestimmung der maximalen Vortriebsleistungen von
Wasserfahrzeugen fest; sie gilt für Wasserfahrzeuge mit einer Rumpflänge von weniger als 8 m.
Diese Internationale Norm gilt nicht für:
_ Wasserskooter nach ISO 13590;
_ Kanus und Kajaks;
_ aufblasbare Boote nach den Teilen 1 bis 3 der ISO 6185 mit Ausnahme starrer aufblasbarer Boote (RIBS), die
eine Geschwindigkeit von 30 kn oder mehr erreichen und nach dieser Internationalen Norm geprüft werden;
_ Rennfahrzeuge: ausschließlich für Wettkampfzwecke konstruierte und gebaute Wasserfahrzeuge.
Diese Internationale Norm legt keine Anforderungen an die Festigkeit des Rumpfes bezüglich der maximalen
Nennleistung fest und garantiert keine Sicherheit der Stabilität unter Seebedingungen, Wind, Kielwasser und
Wellen.

Petits navires d'une longueur de coque de moins de 8 m - Détermination de la puissance maximale de propulsion (ISO 11592:2001)

La présente Norme internationale spécifie les exigences pour la détermination de la puissance nominale maximale de propulsion des bateaux à moteur d'une longueur de coque de moins de 8 m. La présente Norme internationale ne s'applique pas aux : - motos aquatiques, telles que définies dans l'ISO 13590 ; - canoës et kayaks ; - bateaux pneumatiques, tels que définis dans les parties 1 à 3 de l'ISO 6185, avec l'exception que la partie 3 requiert que les bateaux pneumatiques rigides ayant une vitesse maximale de 30 kn ou plus soient soumis à l'essai conformément à l'ISO 11592 ; - bateaux de course: bateaux conçus et construits uniquement pour la compétition. La présente Norme internationale ne spécifie pas d'exigences quant à la résistance structurelle du bateau en relation avec la puissance nominale maximale et ne garantit pas la sécurité face aux conditions de la mer, du vent, du sillage et des vagues.

Mala plovila do 8 m dolžine trupa - Določitev največje moči pogona (ISO 11592:2001)

General Information

• Status: Withdrawn
• Publication Date: 31-Dec-2001
• Withdrawal Date: 10-Apr-2016
• ICS: 47.080 - Small craft
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 08-Apr-2016
• Due Date: 01-May-2016
• Completion Date: 11-Apr-2016
• Directive: 2003/44/EC - Approximation of the laws, regulations and administrative provisions of the Member States relating to recreational craft
• Directive: 2013/53/EU - Directive 2013/53/EU of the European Parliament and of the Council of 20 November 2013 on recreational craft and personal watercraft and repealing Directive 94/25/EC
• Directive: 94/25/EC - Directive 94/25/EC of the European Parliament and of the Council of 16 June 1994 on the approximation of the laws, regulations and administrative provisions of the Member States relating to recreational craft
• Mandate: M/075 - Revised mandate to CEN for standardization in the field of recreational craft
• Ref Project: EN ISO 11592:2001 - Small craft less than 8 m length of hull - Determination of maximum propulsion power rating (ISO 11592:2001)

Relations

• Replaced By: SIST EN ISO 11592-1:2016 - Small craft - Determination of maximum propulsion power rating using manoeuvring speed - Part 1: Craft with a length of hull less than 8 m (ISO 11592-1:2016)
• Effective Date: 01-May-2016
• Replaced By: SIST EN ISO 11592-1:2016 - Small craft - Determination of maximum propulsion power rating using manoeuvring speed - Part 1: Craft with a length of hull less than 8 m (ISO 11592-1:2016)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11592:2002
01-januar-2002
0DODSORYLODGRPGROåLQHWUXSD'RORþLWHYQDMYHþMHPRþLSRJRQD,62

Small craft less than 8 m length of hull - Determination of maximum propulsion power
rating (ISO 11592:2001)
Kleine Wasserfahrzeuge bis 8m Rumpflänge - Bestimmung der maximalen
Vortriebsleistung (ISO 11592:2001)
Petits navires d'une longueur de coque de moins de 8 m - Détermination de la puissance
maximale de propulsion (ISO 11592:2001)
Ta slovenski standard je istoveten z: EN ISO 11592:2001
ICS:
47.080 ýROQL Small craft
SIST EN ISO 11592:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11592:2002

---------------------- Page: 2 ----------------------

SIST EN ISO 11592:2002
EUROPEAN STANDARD
EN ISO 11592
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2001
ICS 47.080
English version
Small craft less than 8 m length of hull - Determination of
maximum propulsion power rating (ISO 11592:2001)
Petits navires d'une longueur de coque de moins de 8 m - Kleine Wasserfahrzeuge bis 8m Rumpflänge - Bestimmung
Détermination de la puissance maximale de propulsion der maximalen Vortriebsleistung (ISO 11592:2001)
(ISO 11592:2001)
This European Standard was approved by CEN on 11 May 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11592:2001 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11592:2002
Page 2
EN ISO 11592:2001
CORRECTED 2002-01-02
Foreword
The text of the International Standard from Technical Committee ISO/TC 188 " Small craft", in
collaboration with CMC.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by December 2001, and conflicting
national standards shall be withdrawn at the latest by December 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of
this standard.
Endorsement notice
The text of the International Standard ISO 11592:2001 has been approved by CEN as a
European Standard without any modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).

---------------------- Page: 4 ----------------------

SIST EN ISO 11592:2002
Page 3
EN ISO 11592:2001
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions
of any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications,
indicated by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 8665 1994 Small craft - Marine propulsion engines and EN ISO 8665 1995
systems – Power measurements and
declarations
ISO 10240 1995 Small craft - Owner's manual EN ISO 10240 1996

---------------------- Page: 5 ----------------------

SIST EN ISO 11592:2002
Page 4
EN ISO 11592:2001
Annex ZB (informative)
Clauses of this European Standard addressing essential requirements or
other provisions of EU Directives
This European Standard has been prepared under a mandate given to CEN by the
European Commission and the European Free Trade Association and supports essential
requirements of EU Directive 94/25/EC.
WARNING: Other requirements and other EU Directive may be applicable to the
product(s) falling within the scope of this standard.
The following clauses of this standard, as detailed in table ZB.1, are likely to support
requirements of Directive 94/25/EC.
Compliance with the clauses of this standard provides one means of conforming with the
specific essential requirements of the Directive concerned and associated EFTA
regulations.
Table ZB.1: Correspondence between this European Standard and EU Directives
Clauses/sub-clauses of this Corresponding annexes/ Comments
European Standard paragraphs of Directive
94/25/EC
1, 2, 3, 4.2, 4.4, 4.5, 5, 6, 7 and Annex I, Clause 4, The Standard provides a
Annex A Handling characteristics method of determining
maximum engine power for
boats of less than 8 m hull
length.
Annex B Annex I, Clause 2.5, A power capacity label is
Owner’s manual not required for Directive
94/25/EC, but the
maximum rated engine
power shall be declared in
the Owner’s Manual.

---------------------- Page: 6 ----------------------

SIST EN ISO 11592:2002
INTERNATIONAL ISO
STANDARD 11592
First edition
2001-06-15
Small craft less than 8 m length of hull —
Determination of maximum propulsion
power rating
Petits navires d'une longeur de coque de moins de 8 m — Détermination
de la puissance maximale de propulsion
Reference number
ISO 11592:2001(E)
©
ISO 2001

---------------------- Page: 7 ----------------------

SIST EN ISO 11592:2002
ISO 11592:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 11592:2002
ISO 11592:2001(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Determination and marking of the maximum propulsion power rating.2
4.1 Outboard powered craft .2
4.2 Other types of craft.2
4.3 Power capacity label and owner's manual.3
5 Test craft preparation.3
6 Test conditions and determination of maximum speed .4
7 Manoeuvring test procedure and criteria.4
Annex A (normative) Manoeuvring test — Craft with v > 7 L kn .6
max
H
Annex B (normative) Owner's manual .7
Annex C (informative) Guidelines for determining the maximum power for initial testing of outboard
powered small craft .8
Bibliography.12
© ISO 2001 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 11592:2002
ISO 11592:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 11592 was prepared by Technical Committee ISO/TC 188, Small craft.
Annexes A and B form a normative part of this International Standard. Annex C is for information only.
iv © ISO 2001 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 11592:2002
INTERNATIONAL STANDARD ISO 11592:2001(E)
Small craft less than 8 m length of hull — Determination
of maximum propulsion power rating
1 Scope
This International Standard establishes the requirements for determination of the maximum propulsion power rating
for engine-driven small craft with a length of hull of less than 8 m.
This International Standard is not applicable to:
� personal water craft as defined by ISO 13590;
� canoes and kayaks;
� inflatable boats, as defined by parts 1 to 3 of ISO 6185, except that ISO 6185–3 requires rigid inflatable boats
(RIBS) capable of a maximum speed of 30 kn or more to be tested in accordance with ISO 11592;
� racing boats: craft designed and constructed solely for competitive racing.
This International Standard does not specify craft constructional strength requirements related to maximum rated
power and does not guarantee security from instability under all conditions of seaway, wind, wakes and waves.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
1)
ISO 6185-3:— , Inflatable boats — Part 3: Boats with a maximum motor power rating of 15 kW and greater
ISO 8665:1994, Small craft — Marine propulsion engines and systems — Power measurements and declarations
1)
ISO 8666:— , Small craft — Principal data
ISO 10240:1995, Small craft — Owner's manual
1)
ISO 11192:— , Small craft — Graphical symbols
1) To be published.
© ISO 2001 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 11592:2002
ISO 11592:2001(E)
3 Terms and definitions
For the purposes of this International Standard, the following terms and definitions apply.
3.1
engine power
engine manufacturer's declared power rated as specified in ISO 8665
3.2
craft speed
2)
speed of the craft on a straight course, measured in knots
4 Determination and marking of the maximum propulsion power rating
4.1 Outboard powered craft
4.1.1 The engine power for performance evaluation for outboard powered craft shall be determined by the craft
manufacturer in accordance with the method given in clauses 6 and 7, and
�
...