SIST EN 50379-2:2012
(Main)Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances - Part 2: Performance requirements for apparatus used in statutory inspections and assessment
Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances - Part 2: Performance requirements for apparatus used in statutory inspections and assessment
This European Standard covers apparatus designed to measure flue gas parameters of heating appliances for domestic residential and commercial applications using commercially available fuels in compliance with metrological specification. The apparatus may consist of different functional modules that may be tested separately for complying with this standard and will be combined in different ways according to the different applications. Part 1 of EN 50379 specifies the general requirements and is supplemented by the requirements in EN 50379 2 and/or EN 50379 3. This European Standard specifies the performance requirements of portable spot reading apparatus designed to give a measurement of specific combustion flue gas parameters such as concentration of gaseous compounds, temperature and/or pressure to be used for testing the compliance with national regulations for the above mentioned appliances. This European Standard excludes apparatus for – continuous emission, safety monitoring and control, and – use in vessels with an international load line. NOTE 1 When this apparatus is used in industrial premises, national regulations should be observed. NOTE 2 Apparatus may contain functional modules that are not covered by this standard e.g. measurement of smoke spot number (see EN 267:2009+A1:2011, Annex A) and/or measurement of indoor ambient air (see EN 50543).
Anforderungen an tragbare elektrische Geräte zur Messung von Verbrennungsparametern von Heizungsanlagen - Teil 2: Anforderungen an das Betriebsverhalten von Geräten für den Einsatz bei gesetzlich geregelten Messungen und Beurteilungen
Spécification pour les appareils électriques portatifs conçus pour mesurer les paramètres des gaz de combustion dans les conduits d'évacuation des appareils de chauffage - Partie 2: Prescriptions des caractéristiques des appareils utilisés au cours des inspections et évaluations réglementaires
Specifikacija za prenosne električne naprave za merjenje parametrov dimnih plinov grelnih naprav - 2. del: Zahtevane lastnosti za naprave, ki se uporabljajo pri zakonsko predpisanem pregledovanju in ocenjevanju
Ta evropski standard zajema naprave za merjenje parametrov izpušnega plina grelnih naprav za gospodinjske in komercialne uporabe s komercialno dostopnimi gorivi v skladu z meroslovno specifikacijo. Napravo lahko sestavljajo različni funkcionalni moduli, ki se združujejo na različne načine v skladu z različnimi uporabami, pri čemer je mogoče ločeno preskusiti njihovo skladnost s tem standardom. 1. del standarda EN 50379 določa splošne zahteve in je dopolnjen z zahtevami v standardu EN 50379-2 in/ali EN 50379-3. Ta evropski standard določa zahteve za delovanje prenosnih odčitovalnih naprav za merjenje posebnih parametrov vnetljivosti izpušnega plina, kot so koncentracija plinastih spojin, temperatura in/ali tlak, za preverjanje skladnosti zgoraj navedenih naprav z nacionalnimi predpisi. Ta evropski standard ne zajema naprav za: – trajno spremljanje in nadzor emisij in varnosti ter – uporabo v posodah z mednarodno tovorno črto.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 50379-2:2012
01-junij-2012
Specifikacija za prenosne električne naprave za merjenje parametrov dimnih
plinov grelnih naprav - 2. del: Zahtevane lastnosti za naprave, ki se uporabljajo pri
zakonsko predpisanem pregledovanju in ocenjevanju
Specification for portable electrical apparatus designed to measure combustion flue gas
parameters of heating appliances - Part 2: Performance requirements for apparatus used
in statutory inspections and assessment
Anforderungen an tragbare elektrische Geräte zur Messung von
Verbrennungsparametern von Heizungsanlagen - Teil 2: Anforderungen an das
Betriebsverhalten von Geräten für den Einsatz bei gesetzlich geregelten Messungen und
Beurteilungen
Spécification pour les appareils électriques portatifs conçus pour mesurer les paramètres
des gaz de combustion dans les conduits d'évacuation des appareils de chauffage -
Partie 2: Prescriptions des caractéristiques des appareils utilisés au cours des
inspections et évaluations réglementaires
Ta slovenski standard je istoveten z: EN 50379-2:2012
ICS:
13.040.40 Emisije nepremičnih virov Stationary source emissions
91.140.10 Sistemi centralnega Central heating systems
ogrevanja
SIST EN 50379-2:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 50379-2:2012
---------------------- Page: 2 ----------------------
SIST EN 50379-2:2012
EUROPEAN STANDARD
EN 50379-2
NORME EUROPÉENNE
April 2012
EUROPÄISCHE NORM
ICS 13.320 Supersedes EN 50379-2:2004
English version
Specification for portable electrical apparatus designed to measure
combustion flue gas parameters of heating appliances -
Part 2: Performance requirements for apparatus used in statutory
inspections and assessment
Spécification pour les appareils Anforderungen an tragbare elektrische
électriques portatifs conçus pour mesurer Geräte zur Messung von
les paramètres des gaz de combustion Verbrennungsparametern von
dans les conduits d'évacuation des Heizungsanlagen -
appareils de chauffage - Teil 2: Anforderungen an das
Partie 2: Prescriptions des Betriebsverhalten von Geräten für den
caractéristiques des appareils utilisés au Einsatz bei gesetzlich geregelten
cours des inspections et évaluations Messungen und Beurteilungen
réglementaires
This European Standard was approved by CENELEC on 2012-03-19. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50379-2:2012 E
---------------------- Page: 3 ----------------------
SIST EN 50379-2:2012
EN 50379-2:2012 – 2 –
Contents
For e wor d . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 5
5 Test methods and performance requirements . 6
5.1 General requirements for tests . 6
5.2 Normal conditions for tests. 6
5.3 Mechanical tests . 6
5.4 Electrical and software tests . 7
5.5 Tests with test gases . 7
5.6 Tests with real flue gases . 8
5.7 Calculated values . 9
5.8 Temperature . 9
5.9 Pressure . 10
Bibliography . 11
---------------------- Page: 4 ----------------------
SIST EN 50379-2:2012
– 3 – EN 50379-2:2012
Foreword
This document (EN 50379-2:2012) has been prepared by CENELEC TC 216 "Gas detectors".
The following dates are fixed:
(dop) 2013-03-19
• latest date by which this document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-03-19
• latest date by which the national
standards conflicting with this
document have to be withdrawn
This document supersedes EN 50379-2:2004.
EN 50379-2:2012 includes the following significant technical changes with respect to
EN 50379-2:2004:
— 5.5.7 considers calibration curves for sensors with nonlinear signal;
— 5.5.8 considers influence of pressure variations;
— 5.5.9 considers the influence of water vapour on the gas signal;
— 5.7.2 for calculated values was amended;
— 5.7.4 considers 15 min. average concentration for solid fuels;
— 5.9.1 was amended to cover measurement at the circular orifice.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
____________
---------------------- Page: 5 ----------------------
SIST EN 50379-2:2012
EN 50379-2:2012 – 4 –
Introduction
This European Standard covers apparatus for measuring gas concentrations and other combustion
parameters, as used in the installation and maintenance of heating appliances. It forms a specification for
portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances,
and includes the following parts under the generic title Specification for portable electrical apparatus
designed to measure combustion flue gas parameters of heating appliances:
Part 1: General requirements and test methods;
Part 2: Performance requirements for apparatus used in statutory inspections and assessments;
Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating
appliances.
EN 50379-1 specifies general requirements for the construction, testing and performance of portable spot
reading apparatus designed to give an assessment of specific combustion flue gas parameters such as
concentration of gaseous compounds, temperature and/or pressure to check the combustion performance of
heating appliances for domestic residential and commercial applications using commercially available fuels.
EN 50379-2 is for apparatus intended to be used for statutory measurement. In several European countries,
legal requirements exist for the performance of heating appliances. Authorised inspectors use these
apparatus to measure the flue gas parameters, in order to test compliance with national regulations. Due to
the legal consequences resulting from the measurement there are strict requirements regarding the
measuring uncertainty of these apparatus. Therefore EN 50379-2 includes maximum values for measuring
uncertainty of the apparatus. Tests with real flue gases form a key part of the verification of the performance
of the apparatus for statutory measurement. The measuring uncertainty has to be justified by internationally
accepted methods over the whole measuring range.
EN 50379-3 is for apparatus intended to be used for non-statutory applications. There are reduced
performance requirements, because the apparatus are designed to decide if maintenance for a gas fired
appliance is required, and for adjusting the appliance during maintenance. There will be no determination of
the measuring uncertainty for the apparatus.
---------------------- Page: 6 ----------------------
SIST EN 50379-2:2012
– 5 – EN 50379-2:2012
1 Scope
This European Standard covers apparatus designed to measure flue gas parameters of heating appliances
for domestic residential and commercial applications using commercially available fuels in compliance with
metrological specification.
The apparatus may consist of different functional modules that may be tested separately for complying with
this standard and will be combined in different ways according to the different applications. Part 1 of
EN 50379 specifies the general requirements and is supplemented by the requirements in EN 50379-2
and/or EN 50379-3.
This European Standard specifies the performance requirements of portable spot reading apparatus
designed to give a measurement of specific combustion flue gas parameters such as concentration of
gaseous compounds, temperature and/or pressure to be used for testing the compliance with national
regulations for the above mentioned appliances.
This European Standard excludes apparatus for
– continuous emission, safety monitoring and control, and
– use in vessels with an international load line.
NOTE 1 When this apparatus is used in industrial premises, national regulations should be observed.
NOTE 2 Apparatus may contain functional modules that are not covered by this standard e.g. measurement of smoke
spot number (see EN 267:2009+A1:2011, Annex A) and/or measurement of indoor ambient air (see EN 50543).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 50270:2006, Electromagnetic compatibility – Electrical apparatus for the detection and measurement
of combustible gases, toxic gases or oxygen
EN 50271:2010, Electrical apparatus for the detection and measurement of combustible gases, toxic
gases or
...
SLOVENSKI STANDARD
SIST EN 50379-2:2012
01-junij-2012
6SHFLILNDFLMD]DSUHQRVQHHOHNWULþQHQDSUDYH]DPHUMHQMHSDUDPHWURYYQHWOMLYRVWL
L]SXãQHJDSOLQDJUHOQLKQDSUDYGHO =DKWHYDQHODVWQRVWL]DQDSUDYHNLVH
XSRUDEOMDMRSUL]DNRQVNRSUHGSLVDQHPSUHJOHGRYDQMXLQRFHQMHYDQMX
Specification for portable electrical apparatus designed to measure combustion flue gas
parameters of heating appliances - Part 2: Performance requirements for apparatus used
in statutory inspections and assessment
Anforderungen an tragbare elektrische Geräte zur Messung von
Verbrennungsparametern von Heizungsanlagen - Teil 2: Anforderungen an das
Betriebsverhalten von Geräten für den Einsatz bei gesetzlich geregelten Messungen und
Beurteilungen
Spécification pour les appareils électriques portatifs conçus pour mesurer les paramètres
des gaz de combustion dans les conduits d'évacuation des appareils de chauffage -
Partie 2: Prescriptions des caractéristiques des appareils utilisés au cours des
inspections et évaluations réglementaires
Ta slovenski standard je istoveten z: EN 50379-2:2012
ICS:
13.040.40 (PLVLMHQHSUHPLþQLKYLURY Stationary source emissions
91.140.10 Sistemi centralnega Central heating systems
ogrevanja
SIST EN 50379-2:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 50379-2:2012
---------------------- Page: 2 ----------------------
SIST EN 50379-2:2012
EUROPEAN STANDARD
EN 50379-2
NORME EUROPÉENNE
April 2012
EUROPÄISCHE NORM
ICS 13.320 Supersedes EN 50379-2:2004
English version
Specification for portable electrical apparatus designed to measure
combustion flue gas parameters of heating appliances -
Part 2: Performance requirements for apparatus used in statutory
inspections and assessment
Spécification pour les appareils Anforderungen an tragbare elektrische
électriques portatifs conçus pour mesurer Geräte zur Messung von
les paramètres des gaz de combustion Verbrennungsparametern von
dans les conduits d'évacuation des Heizungsanlagen -
appareils de chauffage - Teil 2: Anforderungen an das
Partie 2: Prescriptions des Betriebsverhalten von Geräten für den
caractéristiques des appareils utilisés au Einsatz bei gesetzlich geregelten
cours des inspections et évaluations Messungen und Beurteilungen
réglementaires
This European Standard was approved by CENELEC on 2012-03-19. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50379-2:2012 E
---------------------- Page: 3 ----------------------
SIST EN 50379-2:2012
EN 50379-2:2012 – 2 –
Contents
For e wor d . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 5
5 Test methods and performance requirements . 6
5.1 General requirements for tests . 6
5.2 Normal conditions for tests. 6
5.3 Mechanical tests . 6
5.4 Electrical and software tests . 7
5.5 Tests with test gases . 7
5.6 Tests with real flue gases . 8
5.7 Calculated values . 9
5.8 Temperature . 9
5.9 Pressure . 10
Bibliography . 11
---------------------- Page: 4 ----------------------
SIST EN 50379-2:2012
– 3 – EN 50379-2:2012
Foreword
This document (EN 50379-2:2012) has been prepared by CENELEC TC 216 "Gas detectors".
The following dates are fixed:
(dop) 2013-03-19
• latest date by which this document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-03-19
• latest date by which the national
standards conflicting with this
document have to be withdrawn
This document supersedes EN 50379-2:2004.
EN 50379-2:2012 includes the following significant technical changes with respect to
EN 50379-2:2004:
— 5.5.7 considers calibration curves for sensors with nonlinear signal;
— 5.5.8 considers influence of pressure variations;
— 5.5.9 considers the influence of water vapour on the gas signal;
— 5.7.2 for calculated values was amended;
— 5.7.4 considers 15 min. average concentration for solid fuels;
— 5.9.1 was amended to cover measurement at the circular orifice.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
____________
---------------------- Page: 5 ----------------------
SIST EN 50379-2:2012
EN 50379-2:2012 – 4 –
Introduction
This European Standard covers apparatus for measuring gas concentrations and other combustion
parameters, as used in the installation and maintenance of heating appliances. It forms a specification for
portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances,
and includes the following parts under the generic title Specification for portable electrical apparatus
designed to measure combustion flue gas parameters of heating appliances:
Part 1: General requirements and test methods;
Part 2: Performance requirements for apparatus used in statutory inspections and assessments;
Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating
appliances.
EN 50379-1 specifies general requirements for the construction, testing and performance of portable spot
reading apparatus designed to give an assessment of specific combustion flue gas parameters such as
concentration of gaseous compounds, temperature and/or pressure to check the combustion performance of
heating appliances for domestic residential and commercial applications using commercially available fuels.
EN 50379-2 is for apparatus intended to be used for statutory measurement. In several European countries,
legal requirements exist for the performance of heating appliances. Authorised inspectors use these
apparatus to measure the flue gas parameters, in order to test compliance with national regulations. Due to
the legal consequences resulting from the measurement there are strict requirements regarding the
measuring uncertainty of these apparatus. Therefore EN 50379-2 includes maximum values for measuring
uncertainty of the apparatus. Tests with real flue gases form a key part of the verification of the performance
of the apparatus for statutory measurement. The measuring uncertainty has to be justified by internationally
accepted methods over the whole measuring range.
EN 50379-3 is for apparatus intended to be used for non-statutory applications. There are reduced
performance requirements, because the apparatus are designed to decide if maintenance for a gas fired
appliance is required, and for adjusting the appliance during maintenance. There will be no determination of
the measuring uncertainty for the apparatus.
---------------------- Page: 6 ----------------------
SIST EN 50379-2:2012
– 5 – EN 50379-2:2012
1 Scope
This European Standard covers apparatus designed to measure flue gas parameters of heating appliances
for domestic residential and commercial applications using commercially available fuels in compliance with
metrological specification.
The apparatus may consist of different functional modules that may be tested separately for complying with
this standard and will be combined in different ways according to the different applications. Part 1 of
EN 50379 specifies the general requirements and is supplemented by the requirements in EN 50379-2
and/or EN 50379-3.
This European Standard specifies the performance requirements of portable spot reading apparatus
designed to give a measurement of specific combustion flue gas parameters such as concentration of
gaseous compounds, temperature and/or pressure to be used for testing the compliance with national
regulations for the above mentioned appliances.
This European Standard excludes apparatus for
– continuous emission, safety monitoring and control, and
– use in vessels with an international load line.
NOTE 1 When this apparatus is used in industrial premises, national regulations should be observed.
NOTE 2 Apparatus may contain functional modules that are not covered by this standard e.g. measurement of smoke
spot number (see EN 267:2009+A1:2011, Annex A) and/or measurement of indoor ambient air (see EN 50543).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 50270:2006, Electromagnetic compatibility – Electrical apparatus for the detection and measurement
of combustible gases, toxic gases or oxygen
EN 50271:2010, Electrical apparatus for the detection and measurement of combustible gases, toxic
gase
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.